Relay Drivers
Control the energized state of relays.
-
Product
Micro SIL Reed Relays
Series 108
-
SIL relays - 0.15 inch wide packages. Requires a board area of 0.15 x 0.8 inches (3.8mm x 20.3mm). 10 Watts Form A or 3 Watts Form C switches in Mu-metal package
-
Product
SWB-2817, 16x22, 0.3 A, Reed Matrix Module for SwitchBlock
781421-17
Relay Matrix Module
16x22, 0.3 A, Reed Matrix Module for SwitchBlock - The SWB‑2817 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
Dual Channel Clock Driver Card
PI-41400
-
The PI-41400 is a dual channel Clock Driver card capable of operating up to 190 MHz into a 50-ohm load and up to 80 MHz at an amplitude of 8 volts into a 1-megohm load. Into a high impedance load the output voltage range is from a –3 volts to 8 volts with the output pulse amplitude ranging from 0.5 V to 9 V. When driving a 50 load the voltage range is –1.5 volts to 4.5 volts with the output pulse amplitude ranging from 0.25 V to 4.5 V. The rise and fall times of the output pulse are variable from 1.2 ns to 9 ns into a 50-ohm load and <5 ns to 9 ns into a HiZ load. The output pulse amplitude and the load being driven determine the range of variability. The driver output can be set for tri-state operation and the output polarity can be set for ‘Normal’ or ‘Inverted’ operation through software.
-
Product
Diagnostic Relay Buddy 12/24 Test Kit
193
-
Relay Buddy 12/24 Pro Test Kit tests five different relays. Relay Buddy is a quick go / no-go tester for the most common automotive relays and this new version tests both 12 and 24 volt relays. . If the relay fails the test, 3 different trouble codes will advise you of the possible causes for the failed relay. The red LED will flash once, twice or three times to indicate the problem. Trouble code definitions are printed on the back of the tester for your convenience.
-
Product
Teledyne Photometrics Camera Driver
PVCAM
-
PVCAM (Programmable Virtual Camera Access Method) is a software package that contains a robust set of drivers that have been developed to get Teledyne Photometrics camera users up and running in minutes. Before any Teledyne Photometrics camera can be used, PVCAM must be installed on the host computer. The files to install PVCAM are shipped with every camera, whether it be a purchase or a demonstration unit.
-
Product
64 Channel Form A High Power Relay
DP-cPCI-4305
-
DP-cPCI-4305 is a 64-channel 1 Form A, high power relay module. This general purpose relay can be used for high power switching applications. Applications for this module include power routing, automatic test equipment, relay output for soft PLCs and bounce-free switching.
-
Product
4 Relay Channels, Latching
RY2
-
The RY2 module features 4 individual single-pole, user SPDT Form C (changeover/break-before-make type) relays (channels). Each channel has a common input terminal (C), a normally closed output terminal (N/C), and a normally open (N/O) output terminal. The channel either energizes or de-energizes the relays (close or open) so that the signal provided on (C) may be switched/directed to either the (N/C) or (N/O) terminals.
-
Product
Single Phase Relay Testing
-
Megger’s single phase relay test sets are essential items in the relay engineer’s toolbox. Lightweight, rugged with high compliance voltage and test current. Ideal for testing distribution networks, industrial relays, distance relays in rail power networks and many other applications.
-
Product
Rad Hard GaN Drivers
-
The space market has been driving towards more efficient power management solutions. Part of the drive includes the use of Gallium Nitride Field Effect Transistors (GaN FETs) for power conversion. GaN FETs have higher power conversion efficiency and have more natural immunity to radiation, due to them being wide-bandgap semiconductors. Equally important is the use of the correct driver that will allow reliable operation and maximize the benefits of the GaN FETs. Some of the key driver requirements are: a well-regulated gate drive voltage; high source/sink current capability and a split driver output stage.
-
Product
Subminiature Coaxical RF Reed Relays
Series 102
-
Coaxial R.F. Relay. 50 Ohms Independence - Mu-metal SIL package or plastic flatpack. Flatpack - Up to 3 GHz
-
Product
Microwave Relays (SP3T to SP12T)
CXM/3x1 to CXM/12x1
-
CXM/3x1 to 12x1-NO-SMA Microwave Relays are Normally Open (NO) in the OFF state. Only one port can be on at a time. Larger configurations can be built by connecting the common port of multiple relays to another relay in series.
-
Product
Portable Relay Tester
-
The protective devices such as relays, overload coils, circuit breakers must be checked regularly to ensure that, they are always ready to operate correctly. If a fault occurs in the equipment, which they are protecting, routine relay testing will quickly detect the faulty, incorrectly adjusted protection circuit and will possibly prevent serious damage to plant or injury to personnel. Apart from checking the protective circuits correctly, it is usually necessary to measure its operating time. The micro controller based time interval meter is used for this purpose in all AJIT brand relay tester.
-
Product
Brushless DC Drivers (BLDC)
-
Covering a wide range of power systems, our integrated MOSFET and gate driver ICs thrive in automotive, industrial, and consumer applications, ranging from 3.5 to 100 V operating voltage.
-
Product
MTM-Relay: 4-Channel Solid-State Relay (SSR) Module
-
SOLID STATE: The MTM-Relay is a key component to automated manufacturing test systems that require switching of industrial control voltages. Features four software-controlled solid-state relays (SSR) that can handle up to 60V and 6ADC/RMS.
-
Product
Advanced Three Phase Automatic Relay Test Sets
MP 3000 Series
-
Advanced three phase automatic relay test set. PC control through user friendly MPWIN Relay Test Software. High accuracy and high power over wide range. Suitable for IEC61850 GOOSE simulation, subscription and sampled value publishing. CE, FCC.
-
Product
Low Thermal EMF Relays
Series 100
-
The Pickering Series 100 is a complete range of Single-in- Line (SIL) reed relays primarily intended for direct drive from 4000B CMOS or similar low current sources. They feature a very low level of thermal EMF.
-
Product
32 Channel Driver
-
The MultiChannel RF Driver is a 32 channel signal generator / amplifier intended to drive multchannel acousto-optic cells such as the Harris H-601. The driver can be operated either as an RF amplifier, providing 32dB of gain or as a high power signal generator making use of a dedicated 1GSPS, 14bit digital synthesizer on each channel. Modulation can be performed through the use of the internal source, external global input, external individual input, or programmable 16K sample RAM lookup table.
-
Product
Six-Phase Protection Relay Test System
VAE-660
-
Shenzhen Feso Automation Technology Co., Ltd.
Six-Phase Protection Relay Test System. Six current + six voltage channels with 1000 VA single-phase power for differential, distance and high-burden relay testing.
-
Product
Relay Test Equipment
ME3000 Series
-
ME3000 is recently developed low-cost oriented relay test equipment, aimed to supply customer cheaper and cost-effective product.
-
Product
Miniature Instantaneous Relays
CU-D Series
-
Heavy duty miniature power relays for demanding applications, switching of AC&DC voltages, resistive and/or inductive loads. Equippedwith weld no transfer contacts.
-
-
Product
Protection Relay Tester
PW866i
-
PW866i (6×32A, 4×300V) Protection Relay Tester could be used for testing all kinds of relays, also supports testing IEC 61850 combined relays. Its local control system is with 10.4inch LCD screen based on Windows system.
-
Product
Three Phase Relay Testing
-
Our comprehensive and intuitive relay software speeds up testing times with a vast library of pre-defined test regimes or manual operation.
-
Product
Current Differential and Overcurrent Relay
SEL-387
-
Schweitzer Engineering Laboratories, Inc.
Protect and control any two-, three-, or four-winding power transformer with the SEL-387, which provides thermal and through-fault monitoring, and with SELogic Control Equations, can detect breaker failure.
-
Product
8-CH Relay Outputs & 8-CH Isolated DI PCI Cards
PCI-7250/7251
Relay
ADLINK's PCI-7250/7251 provide 4-CH SPDT (Form C) & 4-CH SPST (Form A) relay outputs and 8-CH isolated digital inputs. The status of each relay output is represented by an onboard LED. When the relay is in SET condition, its corresponding LED will turn ON, and on the contrary, it is OFF. All digital input channels are nonpolarity, optically isolated, and may be set to use RC filter or not. The devices are suitable for collecting digital inputs in noisy environments. The PCI-7251 is an 8-CH relay outputs and 8-CH isolated DI extension card of the PCI-7250. All the I/O functions of PCI-7251 are the same as those of the PCI-7250. The PCI-7251 has to be connected with PCI-7250 and the bus interface is controlled by the PCI-7250. Up to three PCI-7251 cards can be connected to one PCI-7250, therefore, expanding the PCI-7250's DIO from 8 DIO to maximum 32 DIO.
-
Product
16-CH Latching Relay Outputs & 16-CH Isolated DI Card
PCI-7256
Analog Output Module
- Supports a 32-bit 3.3 V or 5 V PCI bus- 16-CH latching SPDT relay outputs- Power saving on relay actuation- Output status unchanged when power-off- On-board LED indicators for relay status
-
Product
Latching / Bistable Heavy Duty Power Relays
-
The voltage pulse will activate the relay to pull-in or release the contacts. The latching relay / bistable relay will hold its contactposition till the next voltage pulse. Below latching relays / bistable relays are designed for demanding heavy duty applications.
-
Product
Relay / Magnetic Field Testers
-
PeakTech Prüf- und Messtechnik GmbH
Ideally suited for checking magnetic fields and the correct function of coils, e.g. Relays and solenoid valves. The magnetic field detector works without contact, so that opening the housing is not necessary in most cases. When a magnetic field is detected, the probe tip lights up permanently blue, with clocked relays in the same cycle as they are controlled. The function of the magnetic field detector can be checked before each measurement with the enclosed test permanent magnet.
-
Product
Powertest Relay Test Software
-
For all the three phase or six phase relay testers of PONOVO, one universal software can be used, the name is PowerTest software.
-
Product
Protective Relay Testing Equipment
PW466i
-
PW466i (6×20A, 6×150V) 6-phase relay tester is a powerful secondary injection protective relay testing kit with 6-currents and 6-voltages sources.
