Relay Drivers
Control the energized state of relays.
-
Product
PXI Power Relay Module, 6xSPDT, 16 A, With Interlock
40-161A-102-HI
-
The 40/42-161A-102-HI is a PXI/PXIe 6xSPDT power relay module with optional hardware interlock. It is part of a range of high density power switching solutions with a choice of SPST, and SPDT relay configurations with or without hardware interlock.
-
Product
PXI/PXIe High Density Electro-mechanical Relay Module, 100xSPST, Normally Open
42-145A-201
-
The 40-145A-201 (PXI) and 42-145A-201 (PXIe) 100xSPST relay module is part of a range of high density switching modules available in Normally Open (SPST & DPST), Changeover (SPDT) and Normally Closed (SPST) configurations. Connections are made via a front panel 200-pin female connector.
-
Product
Volt-Finger Detector / Driver
LVD-18
-
Standard Electric Works Co., Ltd
● Bright LED and audible alarm sound when voltage is present.● Designed for both contact and non-contact voltage detection.● Direct contact voltage detection: 50V~600Vac.● Non-contact voltage detection: 50V~600Vac.● Can be used to detect voltage in lighting fixtures, circuit breakers.● Compact and handy.● Can be used to find a break in a wire.● Continuity test and basic driver function..● Flashlight.
-
Product
Ultra High Density 4mm Reed Relays
124-1-A-5/2
-
Single Pole Reed Relays0.5 Amp switchingVery high packing densityStacking on 4mm x 4mm pitch1 Form A5 V Coil
-
Product
Driver Amplifiers (< 3 W)
-
Qorvo's driver amplifiers are designed to provide good linear or efficiency performance for gain stages prior to the final power amplifier in a transmitter chain. These products support frequencies up to 46 GHz, using process technologies such as InGaP HBT, power pHEMT, E/D pHEMT and GaN.
-
Product
Clock Drivers
-
Multiple timing signals ("clocks") are required by CCDs, IR FPAs, and some CMOS image sensors to transport electrical charge across the array to a sense amplifier for conversion into image data. Pulse Instruments offers a line of "clock drivers" for generating these timing signals. The parameters of these clocks (clock rate, pulse width, pulse amplitude, rise- and fall-times, etc.) greatly influence the behavior and performance of the imaging device. Our products take logic-level inputs from a pattern generator and allow the user to adjust the output parameters to suit their device and testing requirements. Clocks can be "tweaked" in real-time to determine optimal operating parameters for a particular device, or else programmed in accordance with a test plan for automated production test.
-
Product
PXI/PXIe Microwave Relay, Dual SPDT, 18GHz, 50Ω, SMA, Remote Mount
40-780B-522-E
-
The 40-780B-522-E (PXI) and 42-780B-522-E (PXIe) are dual SPDT 18GHz unterminated microwave relay modules with remotely mounted relays. The 40/42-780B range is available with one, two, three or four SPDT panel mounted relays capable of switching frequencies up to 67GHz in 50Ω or 2.5GHz in 75Ω. Connections are made via high quality RF coaxial connectors, SMA or N-Type for 50Ω and 1.6/5.6 in 75Ω versions. Remote versions can support up to three SPDT relays in a single slot.
-
Product
PXI/PXIe Microwave Relay, Dual SPDT, 18 GHz, 50 Ω, SMA, Failsafe
42-780B-522
-
The 40-780B-522 (PXI) and 42-780B-522 (PXIe) are dual failsafe SPDT 18 GHz unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions are also available which can support up to three SPDT relays in a single slot.
-
Product
PXI Mixed Configuration Relay Module - 2 Cells Populated
40-138-AA-BB-CC-DD (2 CELL)
-
The 40-138 2A Relay Module with 2 cells populated is a cell-based mixed configuration switching module suitable for applications requiring medium power switching with high density. It provides a broad selection of mixed relay types for greater flexibility and features 2A current capacity and voltages to 300VDC/250VAC.
-
Product
PXI Microwave Relay, Single SPDT, 26.5GHz, 50Ω, SMA, External Termination
40-781A-321
-
The 40-781A-321 (PXI) and 42-781A-321 (PXIe) are single SPDT 26.5GHz microwave relay modules with external terminations. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50GHz in 50Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
Product
SWB-2815, 4x86, 0.3 A, No Row Access, Reed Relay Matrix Module for SwitchBlock
781421-15
-
4x86, 0.3 A, No Row Access, Reed Matrix Module for SwitchBlock - The SWB‑2815 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
PXI/PXIe High Density Electro-mechanical Relay Module, 32xSPDT
40-148A-001
-
The 40-148A-001 (PXI) and 42-148A-001 (PXIe) 32xSPDT relay module is part of a range of high density switching modules available in Normally Open (SPST & DPST), Changeover (SPDT) and Normally Closed (SPST) configurations. Connections are made via a front panel 200-pin female connector.
-
Product
Relay Buddy
190
-
Relay Buddy is a quick go / no-go tester for the most common automotive relays. It provides you with an indication of the general health and functioning of the relay switch contacts and coil. Relay Buddy will check the control side of the relay by applying a signal to the relay coil while it checks for proper functioning of the relay contacts. Relay Buddy operates the relay several times during each test session as it watches for consistency in every cycle. Relay Buddy will fail the relay and light the RED LED if any one of the cycles proves unsuccessful during the test session.
-
Product
Relays & Timers
-
Relays are switches that open and close circuits electromechanically or electronically. Timers control timing in applications where functions need to be delayed or loads need to be maintained for a predetermined period.
-
Product
Dual Channel Driver Card
42460
-
Two channels of 32 MHz clock drivers with up to 20 volt amplitude. The output voltage range is ±20 V, with independent high and low voltage settings. The inputs to the Card can be optically isolated. The card also contains voltage and current sense capability, which allows muxing of the current or voltage output measurements from all the Driver Channels in the system to a single DVM. The card allows independent programming of the rise and fall time of each channel one nanosecond increments.
-
-
Product
PXI/PXIe Microwave Relay, Dual SPDT, 67 GHz, 50 Ω, SMA-1.85, Remote Mount, Failsafe
42-780B-572-E
-
The 40-780B-572-E (PXI) and 42-780B-572-E (PXIe) are dual failsafe SPDT 67 GHz unterminated microwave relay modules with remotely mounted relays. The 40/42-780B range is available with one, two, three or four SPDT panel mounted relays capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions can support up to three SPDT relays in a single slot.
-
Product
Relay Tester
LET-4000-R
-
Regulation and Measurement Module performs the regulation of the DC current and is made with a variable auto transformer (Variac) regulating a three phase DC current, with a power of 8KVA and a three phase transformer of 8KVA with 2V nominal power in the secondary windings. A built-in ammeter and a timer give the information of the current injected and the operation time of the relay under test.
-
Product
LXI Microwave Relay, 50Ω 12xSPDT 18GHz SMA
60-890-003
-
Model 60-890-003 Microwave Relay is suitable for switching 50Ω signals up to 18GHz. With 12 banks of SPDT relays it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA connectors.
-
Product
Programmable Relays
-
You get in one unit 12 Inputs and 8 Outputs relays or transistor. Herewith you can do a lot of bigger scale automation whereas the 10 I/O versions are just to short of I/O’s.
-
Product
Isolated Gate Drivers
-
Analog Devices’ isolated gate driver portfolio offers designers performance and reliability advantages over designs utilizing optocouplers or pulse transformers. Utilizing ADI’s proven iCoupler® technology, the isolated gate driver family offers the advantage of a maximum propagation delay of 50 ns, less than 5 ns channel-to-channel matching, a 50-year lifetime for 400 V rms working voltage and galvanic isolation in a single package.
-
Product
SparkFun LED Driver Breakout
TLC5940 (16 Channel)
-
The TLC5940 is a 16 channel PWM unit with 12-bit duty cycle control (0-4095), 6 bit current limit control (0-63), and a daisy chainable serial interface. This breakout board is a good way to take full advantage of this useful IC. All 16 PWM channels are broken out to standard 0.1" headers, which run alongside convenient voltage and ground rails. Also, because the TLC5940 can be daisy-chained, the breakout is designed to support that feature. On the left-hand side of the board all serial inputs are broken out to 0.1" headers and likewise with output on the right-hand side.
-
Product
Dual Channel Tri-Level Driver Card
40465
-
Two channels of 10MHz drivers, that can be operated as standard Two-Level Drivers or operated as two channels of Tri-Level Drivers. In the Two-Level mode, the input to each driver channel requires one channel of TTL level timing. Tri-and four level modes require a second clock input. In the Tri-Level Mode, the output from lowest rail to high rail can be 18.5V. Like the 40460 the rise and fall time as well as the high and low voltage levels of each channel is programmable.
-
Product
PXI 8 x DPDT Power Relay Module, 5A
40-157-001
-
40-150/151 modules have 8xDPST or 12xDPST power relays, suitable for switching inductive/capacitive loads up to 5A at 250VAC. 40-155/156 modules have 8xSPDT or 16xSPDT power relays and 40-157 is configured as 8xDPDT. Power relay modules are intended for switching heavy AC or DC loads or for slave switching large external relays, contactors and solenoids. The 40-150 series of power relay module are suitable for applications requiring switching of either mains voltage or DC current.
-
Product
PXI/PXIe High Density Reed Relay Module, 50xSPST
42-140B-021
-
The 40-140B-021 (PXI) and 42-140B-021 (PXIe) are 50xSPST general purpose switching modules. They are part of a range of high density relay modules using ruthenium reeds available in 50x, 75x and 100x Normally Open SPST configurations. Connections are made via a front panel 200-pin female connector.
-
Product
PXI/PXIe High Density Electro-mechanical Relay Module, 100xSPST, Normally Open
40-145A-201
-
The 40-145A-201 (PXI) and 42-145A-201 (PXIe) 100xSPST relay module is part of a range of high density switching modules available in Normally Open (SPST & DPST), Changeover (SPDT) and Normally Closed (SPST) configurations. Connections are made via a front panel 200-pin female connector.
-
Product
Time Relays
-
ENTES Time Relays are designed to enable control in desired time intervals and have various functions.
-
Product
Low-Side FET Drivers
-
Renesas' low-side FET drivers are very high-speed matched dual-drivers capable of delivering peak currents into highly capacitive loads and are excellent at driving large capacitive loads with minimal delay and switching times.
-
Product
Stepper Motor Drivers
-
ST's portfolio of STSPIN stepper motor drivers spans from relatively simple ICs with current control and phase generation to more complex solutions.
-
Product
FET Solid State Switch, 300 kHz to 18 GHz, SPDT
U9397C
-
The Keysight U9397C solid state switch maximizes your frequency range from 300 kHz up to 18 GHz, offering excellent performance with high isolation, low SWR and fast switching speed. Applications include instrumentation, communications, radar, and many other test systems that require high speed RF and microwave SPDT switching.
