SCR
Thyristor, Silicon Controlled Rectifier
-
Product
Millivolt Drop Tester
-
The SCR ELEKTRONIKS Millivolt Drop Tester is an industry acclaimed product. MVDT has a specially built constant current source (current generator) up to 400A (depending on model) and a dedicated PLC to store test parameters (in automatic models), perform test procedure, make the millivolt drop & junction resistance measurements and store test results, that can be retrieved later or downloaded to PC. PC based TestWare can display the test results & export those to Office, HTML, Printer or PDF. The manual models consist of the constant current source, digital ammeter and a digital millivolt meter with 3 ranges.
-
Product
Earth Contact Resistance Tester
-
SCR ELEKTRONIKS have developed an equipment namely Earth Contact Resistance Tester to test the appliance. To ensure the safety of operator it is essential that the Earth path (connection) should offer minimum impedance to by pass short circuit Current to Earth. This is ensured by measuring Resistance of the Earth path by passing heavy Current say 25 A. The Earth Contact Resistance Tester essentially comprises of a Variable Current source with digital Ammeter to measure the Current supplied. The Voltage drop across the Earth path is measured with a digital Voltmeter. Optionally for a particular Current (25 A) the meter can be calibrated in terms of Resistance. A timer is provided to switch off the Current after the Set Time.
-
Product
Test Finger Apparatus
-
SCR ELEKTRONIKS focuses on designing a solution around the end use at her customer. Instead of offering a standard instrument for a specific task, we have an approach of customizing the test bench to target the specific goals of the process or test procedure. Our measurement instruments, test modules, electrical power systems & software libraries are developed with this vision, thereby reducing the test system’s time-to-deploy.
-
Product
Bench Digital Multimeter, 3.8, USB, 20 A, 1 kV, 60 Mohm
72-13620
-
*True RMS bench top digital multimeter with 6000 counts display*CAT II 600V safety rating*Manual function select and auto ranging*Transistor & SCR measurement*Data hold, max/min modes*EBTN (Enhanced Black Twisted Nematic) LCD backlight*USB interface*Input protection*Powered by 100V/120V/220V/240V ±10%, 47Hz to 63Hz supply*12-month limited warranty *view Terms & Conditions for details
-
Product
Safety Test Panel for Luminaire Fixture
-
SCR ELEKTRONIKS introduces Safety Test Panel for Luminaire with PC Datalogging. The tests are Performed as Prescribed in IS the Panel Carries out different tests one by one and provides indication of the Test results as OK or NOT-OK. It is very useful and handy in line testing on Mass production line as well as type Testing.
-
Product
MCB Endurance Test Bench
-
The SCR Elektroniks Endurance Test Bench is designed for electrical and mechanical endurance MCB and RCCB as per clause 9.11 of IEC 60898-1. The source and the load is designed to comply as per the general test conditions specified in Cl 9.11.1. The accompanying pneumatic fixture is designed to hold custom built designs of MCB and RCCB while the microcontroller based timer unit can be configure to follow test procedure summarized in Cl 9.11.2.
-
Product
PC Based Comprehensive Test Setup for Luminaires
-
Our zest for innovation has resulted in continuous upgrades in the existing line of products. Till now we used to manufacture 3 different equipments for Driver, MCPCB and Luminaires Component testing. We at SCR Elektroniks have developed our comprehensive tester to incorporate all the 3 systems in a single bench. Here in this tester one can test all the three DUT in a single bench. Since all the 3 testing procedures have many tests in common, we have incorporated all the tests in a single bench such that testing of Luminaire driver, Luminaire PCB and Final Luminaire set is performed in single test bench. Only these tests are performed over the DUT else other are disabled for them.
-
Product
Programmable Parametric Tester For Discrete Semiconductors
IST-8800
-
IST Information Scan Technology, Inc.
The IST-8800 is a fully programmable, low cost tester that provides parameter measurements or parametric GO/NO GO test for transistors, diodes, MOS-FETs, Regulators, Triacs, Zeners, SCRs, and J-FETs. These devices can be tested up to 5 amps or 1200 volts with a measurement range down to the nano amp range. Only four universal test fixtures are required which can test the device across a wide range of packages.
-
Product
SCR Controller with Regulator
-
The SCR Controller and the Regulator Board are used in SCR controlled power supplies.CEHCO offers single phase and three phase SCR Controllers with Regulator Boards.
-
Product
Run Down Adapters
Screw RDA
-
The screw run down adapters are designed only for EZ-TorQ analyzer. These devices provide consistent and reliable torque readings for use with power-driven torque control tools. The RDA reduces the impact and irregular peaks that cause poor repeatability. The run down adapter is mounted in-line between the tool drive and transducer.
-
Product
4 Station Endurance Test Setup for Thermostat of Iron
-
SCR ELEKTRONIKS have developed 4 STATIONS ENDURANCE TEST SETUP FOR THERMOSTAT OF IRONwhich is used for carrying out endurance test for thermostat of iron for the required amount of time It is very useful and handy in line testing on Mass production line as well as type Testing. It consists of Voltmeter, Wattmeter, Programmable Logic Controller( PLC ). The equipment continuously monitors faults like Contact weld and Contact Open. The other important feature is we can operate the panel in Auto Mode or Manual mode. User friendly operations make the equipment to be handled easier for any operator. This manual contains information about operating instructions and maintenance of the equipment.
-
Product
12 Pulse SCR Controlled High Voltage Power Supply
-
- 12 Pulse SCR Controlled Power Supply, P/N 19435PS- Input: 480 VAC, 300 Amps, 3 PH, 60 Hz- Output: 0 to 3000 VDC ± 10%, 80 Amps max adjustable with potentiometers, and 4/20 mA input signals from the PLC- Output voltage and current are provided as 4/20 mA signals to PLC- Contactor and overload relay are installed for protection- Power ON Light- Start / Stop capability- EPO capability- Manual voltage control and current limit- PLC interface- Output voltage and current are displayed on the voltmeter and ammeter.- A selector switch is used to select between manual Control or PLC Control- The customer is responsible for the PLC controller and PLC programming- Power enclosure, 68″H x 65″W x 44″D- Control enclosure: 20″H x 16″W x 9″D- Weight: 5000 lbs. approximately- All input/output connections are inside the enclosure
-
Product
Endurance Test Panel For Domestic Mixer
-
SCR ELEKTRONIKS have developed ENDURANCE TEST PANEL FOR MIXER for carrying out endurance test of mixer at final stage. It consists of Voltmeter, Ammeter, Wattmeter & Temperature Indicator for observing the values of different parameters. Output Socket is provided for quick connections and disconnections of the equipment to be tested. User friendly operations make the equipment to be handled easier for any operator.
-
Product
MCB Tripping Current Characteristic Test Bench
-
The SCR Elektroniks 12 station MCB Tripping Characteristics Test Bench is optimally designed to verify the Tripping Characteristic of MCBs as per clause 9.10.1 of IEC 60898 (Also mentioned in Indian Standards IS 8828). The bench essentially comprises of Servo Controlled mechanism to set and maintain desired current (against incoming mains fluctuation) and a Micro controller based master controller unit plus timer, which governs the entire sequence of operation making it a stand-alone system once the user connects the MCB and configures the test parameters.
-
Product
Bus Analyzer
Scribe I2C
-
The Blackhawk Scribe is an entry level, yet feature-packed and robust I2C debugging tool. The Scribe was designed to help engineers developing products which utilize the IC and SMBus interfaces.
-
Product
Software
Scream!
-
Scream! is a Windows and Linux application for Seismometer Configuration, REal‑time Acquisition and Monitoring.
