Current Transformer Test
measures insulation, excitation current, turns ratio, winding polarity saturation and/or winding resistance. Current Transformers
See Also: Transformer Test, Transformer Testers, Current Transformer Test Set
-
product
622 HP Eddy Current Chassis Dynamometer
CM-51-EC
Weight Capacity: 25,000 lb (11,340 kg) per axleRoll Brakes: pneumatically-actuated discShipping Weight: 8,340 lb (3,783 kg)Capacity: 622 hp at 45 mph (464 kW at 72 kph)Rolls: 20 by 36 in. (508 by 915 mm) long4 front fixed rolls, 2 rear rolls fixed toaccommodate axle spreads from48 to 60 in. (1,219 to 1,524 mm)tandem centersPit Required Depth: 25 in. (635 mm)
-
product
SAFETY TESTERS ( CURRENT LEAKAGE TESTERS )
ST-05
Safety Tester Model ST-05 is a test set for testing small equipment powered by 120V 60 Hz, from an approved U-ground source. Test also can be run on double-insulated tools an on appliances with two-pin parallel plugs.
-
product
Test Services
INFRAMET offers two types of services in field of electro-optical imaging systems: 1)Trainining and consulting; 2)Test services.
-
product
Machinery Testing
Product Safety Consulting Inc.
Product Safety Consulting guides you through the process of obtaining safety certification in the fastest time and for the least cost. We have years of experience testing products according to applicable standards. We help you not only verify the classification of your machinery, but get you through the conformity assessment process – from designing for compliance, to applicable essential requirements, to testing your product, to achieving certification.
-
product
Thin Film Current Sensing Chip Resistors
CSTN
*Thin film process*High power rating up to 3 watts in 2512 size*Resistance values from 50m to 1ohm*High purity alumina substrate for high power dissipation*Power management applications*Switching power supply*Over current protection in audio applications*Voltage regulation module (VRM)*DC-DC converter, battery pack, charger, adaptor,*Automatic engine control*Disk drive
-
product
Magnetic-Inductive Testing
MAGNATEST® Product Family
Foerster Instruments, Incorporated
The MAGNATEST product family is used for the non-destructive testing of metallic materials for magnetic and/or electrical properties. The test instruments are used in the automotive and aviation sectors as well as in the production of semi-finished products. The focus is on testing components relevant to safety such as brake discs, or ball pins and functional components such as camshafts and drive shafts, pivots and piston pins. Typical test tasks include hardness checks, material differentiation and sorting. MAGNATEST can also be used for the automatic testing for the geometric properties of all metallic series components. The high-performance amplifier installed in MAGNATEST test instruments makes it possible to analyze harmonics, which guarantees an extremely reliable and precise repetition, even when impacted by perturbations.
-
product
Primary Current Injection Test Sets
Our primary current injection test sets cover from 750A through to 6000A. Available in single phase, testing applications include testing and timing of under and over current relays, circuit breakers and CT ratio testing.
-
product
Test Equipment
Rotary Field Checker
Smart Three Phase Rotation Tester. Test Leads. Phase Rotate Tester is a 3 phase tester to identify the correct connection from the power supply. Also, it can identify the missing phase of the power supply too.
-
product
Battery Testing
With the increasing dependency of back up systems on battery strings, and the escalating cost of replacing batteries, instrumentation and software systems that can measure, trend and manage the life-cycle of cells is a cost effective option.
-
product
Test Systems
As new products emerge and change, the requirements for the industry also increase becoming more and more challenging. Complex products require demanding and versatile test systems, capable of performing complex test cycles. The ultimate goal is to ensure the validation of the final product during the different stages of the production process.
-
product
Testing Services
The EI Group, Inc. (EI) is an environmental, health and safety consulting firm that offers comprehensive services to a variety of public and private sector clients. Founded in 1988, EI boasts a staff of professionals that have the experience and training required to provide cost-effective, results-oriented consulting services across the United States and abroad. These services are provided with an aggressive, relationship-focused philosophy in order to exceed our clients' expectations regarding quality and timeliness.
-
product
Test Management Software
ActivATE™
Easily create and run robust test programs in semiconductor automated test systems with ActivATE™ test management software. Designed by test engineers for test engineers, ActivATE™ tames automated test complexities with elegant simplicity.
-
product
Precision Voltage and Current Sources
VI-700
The VI-700 Voltage and Current Source is a versatile precision dialable or remotely programmable voltage and current source. Its three ranges provide up to 20 V full scale (200 V with the HV option), and down to 100 mV resolution; and 20 mA full scale down to 0.1mA resolution. Both voltage and current outputs are available simultaneously. The output is set by a range selector and thumbwheel switches in the LOCAL mode, or by a digital input at the rear panel. The REMOTE mode control can be a RS232 or IEEE-488 interface.
-
product
High-Voltage, High Current I/O Module
Model JI-4516
The JI-4516 module is a versatile, easy-to-use device for adding high-voltage, high-current digital I/O capability to a computer system via a USB connection. The module is comprised of 8, low-side power MOSFET switches, and 8 high-voltage inputs. I/O ground isolation eliminates ground-loops and provides protection from noise and switching transients during high-current load switching. The JI-4516 is available as either a desktop unit or low-cost OEM board.
-
product
H(3)TRB & HTGB Test Systems
SET offers two H(3)TRB and HTGB product lines which differ in the number of test object channels and the range of technical possibilities. The innovative systems are scalable, modular and standardized.
-
product
Distribution Transformer Tester
ADOC-3
The ADOC-3 is an equipment that has been designed to test distribution network transformers from 5 kVA to 3MVA.
-
product
Wall Transformer, Converters & Chargers
PeakTech Prüf- und Messtechnik GmbH
An appliance for holding or inserting a charge of power.
-
product
Field Testing
Electronic force measuring device with digital display in MN / m², switchable for load plate.
-
product
Resistors for Calibration of Current Measuring Systems and Sensors/Transducers
ChenYang Technologies GmbH & Co. KG
Is designed and made according to the Standard JB/T8225-1999 for DC resistors used in laboratory and electrical engineering.By using full closed structure and automatictemperature control it ensures resistor good long-term stability and small temperaturecoefficient. This DC resistor is very suitablefor DC current measurement and calibration of current measuring systems and current sensors. The maximal measuring current is 100A with measuring accuracy of ±0.02%
-
product
Railway Testing
In the railway transportation testing filed, PONOVO has launched the DC testing equipment from low current output level upto 15,000 dc current to meet different testing requirement.
-
product
High-Speed Transformer Test System
DU-7211
Delta United Instrument Co., Ltd.
Inductance, Q factor, Leakage Inductance, AC Resistance, Capacitance, DC Resistance, Balance,Turn ratio, Open/Short check
-
product
Single-Phase Transformer Winding Resistance Meters
RMO-TT Series
RMO-TT series is perfect for measuring winding resistance of inductive objects such as power and distribution transformers or autotransformers. Additionally, every transformer resistance meter from RMO-TT series can analyze:tap changers,generators,electrical motors,high-current busbar joints,cable splices,and welding joints.Transformer demagnetization can also be performed with all RMO-TT instruments.The series is consisted of 3 models, with maximal test current from 40 A (RMO40TT) to 100 A (RMO100TT). RMO100TT is the only portable transformer resistance meter in the market with 100 A DC output current.The three independent channels enable testing of three windings in series. Consequently, a user can measure winding resistance in every tap position of an on-load tap changer without discharging between the tests.In addition to winding resistance measurement, a user can perform a detailed on-load tap changer analysis by analyzing recorded graphs (10 kHz sampling rate) and by measuring vibrations on an external tap changer tank.All RMO-TT instruments have a built-in tap changer control unit. Because of this, it is possible to remotely control on-load tap changer (OLTC) directly from the device. Also, a user can program DV-Win software to do everything automatically – running winding resistance tests and changing OLTC tap positions.The DV-Win software also enables control and observation of the test process, as well as saving and analyzing the results on a PC. It provides a test report, arranged in a selectable form as an Excel spreadsheet, PDF, Word, or ASCII format. Additionally, DV-Win measures and calculates the OLTC transition time, the ripple and the winding resistance for each tap changing operation. The software can also perform the calculations necessary for the “Heat Run” test.All results can be exported in the report format.
-
product
RF Transformers
Pulse continues to lead the way with a broad range of components that enable twisted-pair copper high-speed services to homes and businesses. Pulse components are also used in cable modems and the consumer electronics that provide home networking services. Our high-performance transformers support home phone line and power line networks. These transformers are designed to exceed ANSI and ETSI standards, and have excellent THD performance and small footprints.
-
product
Test & Measurement
High-quality connection solutions for precise measuring, testing and examination. Whether low or medium voltage range, whether precise test runs or preventive measuring and testing: With an extensive portfolio of specific components and cables, Stäubli always ensures perfect and reliable contact between the measuring instrument and the points, objects and systems to be tested. In addition, we are a proven partner of leading manufacturers of measuring instruments in this field, for example for equipping them with high-quality sockets. Every product meets all quality and safety standards.
-
product
PXI Analog Output / Current Loop Simulators
These modules are aimed at simulating industrial control transceivers, utilizing 4–20mA current loops. The modules include built-in relays for shorts and opens functionality enabling fault insertion testing on every channel and also enable slew rates to be programmed so that different sensors can be effectively mimicked.
-
product
Test Handler
HA1200
The new HA1200 handler can be linked with a tester to utilize our unique active thermal control technology for testing singulated and/or partially assembled dies. This technology enables testing of powerful high-end SoCs with 100% test coverage. This helps reduce yield loss at final test, thus reducing losses of final multi-die assembled products.
-
product
Sync Test
Paragon neo-S
Capture and decode PTP packets for analysis and Time Error testing. PTP clock emulation, plus the Paragon neo-S’ conformance test applications, removes uncertainty and maximizes test repeatability – essential for validating new, high-accuracy 5G network devices.
-
product
True RMS Current Clamps
PeakTech Prüf- und Messtechnik GmbH
Current clamps are ideal for current measurement in electrical systems and control cabinets, since only single wires are guided through the clamp jaws for contact-free current measurement and no electrical connections have to be disconnected. In addition, this model has extensive multimeter functions for voltage, resistance, frequency, capacitance and temperature measurement.
-
product
Test Chambers
Drug test chamber, ozone test chamber, plant grown chamber, salt spray test chamber, sand test chamber, temperature and humidity test chamber, UV test chamber, xenon test chamber
-
product
Testing Consumables
Solar Light offers a plethora of consumables for SPF and other testing requirements, including high quality Molded and Sandblasted PMMA Plates, Pre-Analyzed and Certified SPF and UVA Sunscreen Standards, Disposable Medical-Grade Pads, and long-life spare Xe Lamps for use with our state of the art Solar Simulators.
