Surge Testers
Analyze device performance under a sudden increase of electrical power.
See Also: Hipot Testers, Impulse Winding Testers
-
Product
Uniaxial Powder Tester
UPT
-
The Uniaxial Powder Tester (UPT) is a unique stand-alone uniaxial shear tester for simple, sensitive and cost effective powder characterisation. The instrument delivers repeatable and reliable measurements, providing a robust alternative to traditional powder testing techniques.Uniaxial testing first involves the construction of a consolidated powder column. This is then removed from its confining sleeve before being fractured through the application of a vertical stress, directly measuring the uniaxial Unconfined Yield Strength (uUYS). This technique can therefore be used to assess and rank powder flowability.
-
Product
Lan Cable Tester
185 LCT
-
Standard Electric Works Co., Ltd
Designed for RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable. The LAN cable tester can verify cable continuity, open, short circuit and miss-wired. The remote receiving unit is available for installed cables far away either on the wall plates or on the patch panels. Auto and manual scan functions. Ground wire test. Lock status function. Buzzer sound warning for wire status. Display : LED indication for wire status.
-
Product
ADSL Testers
-
The common used ADSL Tester is ADSL2+ Tester. It is an easy-to-use, hand-held advanced telecommunication tester that used for the installation, maintenance and measurement of ADSL2+ service. This tester supports the testing function such as parameter, error, DMM, PING that related to ADSL2+ service, user register authentication on the ADSL2+ user’s line side. It also directly enables the engineers to verify, troubleshoot and evaluate the ADSL2+ service. It is the right tool for the network test job.
-
Product
Earthing Resistance Tester
JYD-10A
-
transformer neutral grounding resistor is the vital need in medium voltage AC distribution network that are also called by different names like Neutral Earthling Resistors. They are taken into use to limit the current that would flow through the neutral point of a transformer or generator in the event of an earth fault. They are also used for resistance grounding of connected generators and transformers.
-
Product
Battery Load Tester
BT-100
-
Schumacher Electric Corporation
FOR EVERYDAY DIY USEEasy to operateTest load, battery condition, starter motor draw and complete charging system diagnosis.Works on 6 and 12 volt batteries50 amp load test for 6 volt batteries100 amp load test for 12 volt batteries Tests 6 and 12 volt batteries ─ up to 1000 CCATop-mounted rocker switch for easier operationSuper-grip, heavy-duty color-coded battery clampsEasy-to-read meter ─ accurate and shock resistantBaked enamel, steel case ─ ventilated to keep coolRubber insulated carrying handle ─ for comfort and safety
-
Product
Circuit Testers
-
Precision Mastech Enterprises Co.
Portable, handheld electrical tools used to detect voltage, verify electrical power, check for continuity (broken circuits), and test for proper grounding in electrical systems, outlets, and automotive components.
-
Product
Dedicated Testers
-
Dedicated Testers are often inexpensive due to their low test point requirements, which allow for a reduction in switch cards, especially when compared with a Universal Tester. Ease of setup is accomplished through the utilization of transfer connectors between the fixture and the machine. However, this can contribute to a higher fixture cost than typically seen with a Universal Test Fixture due to the nature of their construction which is labor intensive.
-
Product
Voltage & Continuity Tester
-
Heavy Duty Solenoid Voltage & Continuity Tester - LCD Live Wire and Stud Detector for carpenters and electricians.
-
Product
Gem Testers
-
Fuzhou Zhongtuo Optoelectronic Co.,Ltd
A diamond tester is a portable device used to check the authenticity of diamonds and test materials for their thermal and electrical conductivity. It can accurately indicate if the stone is a real diamond based on the gem's physical properties.
-
Product
Earth/Ground Resistance Tester
DE-5030
-
Earth resistance range0~12 / 0~120 / 0~1200 Normal operation conditionsBattery voltagein range of "BATT.GOOD" Earth voltage measurementmax. AC 30V Output current3mA Response timewithin 1 sec. Insulation resistancemin. 100M / DC1000V between input terminals and case Withstand voltageAC3700V (50 / 60Hz) for 1 min. between input terminals and case Battery Check Battery1.5V x 4 Safety standardIEC 61010-1 CAT.III 300V IEC 61557, IEC61010-031
-
Product
Adhesive Tack Testers
-
Adhesion test is to measure the initial tack and holding power of adhesive tapes and labels. Tack or holding power test is very important in packaging industry and adhesive industry.
-
Product
Folding Tester
FOT-01
-
Jinan Leading Instruments Co., Ltd.
FOT-01 Folding Testeris designed according to relevant standards and adopts modern mechanicalphilosophy and computer processing technology. Folding tester complies with relevant standard. It is suitable to test fatigue strength of paper, paperboardand other sheet material, which thickness is less than 1mm.
-
Product
Continuity Testers
-
The extremely versatile continuity tester offers an insulated, shock-resistant and break-proof plastic housing. The pluggable and screwable connection between the test leads and the terminal post is safe to touch. The continuity test is indicated by an acoustical and an optical signal. The integrated torch light allows you to find wires quick and safe under though circumstances.
-
Product
CELL TESTER
SPOTLIGHT
-
SpotLIGHT was designed to minimize maintenance and to significantly reduce downtime. The lifecycle of its contacting system is longer than that of standard systems currently available on the market, thus substantially reducing TCO.
-
Product
Insulation Resistance Tester
-
Aarohi Embedded Systems Pvt. Ltd
Aarohi make device enable us to measure electrical leakage in wire, results are very reliable as we shall be passing electric current through device while we are testing. The equipment basically uses for verifying the electrical insulation level of any device such as motors, cables, generators, windings, etc.
-
Product
Current Transformer Tester
CTT
-
The CTT is designed to test the current transformer ratio, Phase shift, Polarity, Excitation, Saturation, Winding resistance and Insulation resistance using the voltage method in compliance with ANSI/IEEE C57.13.1 and IEC 60044-1 standards, where voltage is applied to the secondary X terminals of the current transformer.
-
Product
Pendulum Impact Testers
-
Tinius Olsen manufactures several high capacity pendulum impact testers, most of which can be easily changed from a Charpy to an Izod configuration or even to a tensile impact configuration. These testers come in several capacities and are designed primarily for determining the impact resistance of metals. They are designed to fully comply with the specifications outlined in ASTM E23, BS EN ISO 148-3, BS EN ISO 148-2 and ISO 442.
-
Product
Multifunction Installation Testers
-
Shanghai Beha Electronics Co., Ltd.
Loop impedance and prospective short circuit current measurement• Line impedance and prospective short circuit current measurement• Earth loop resistance in TT-systems• Rotary field test• RCD measurements (contact voltage, trip time, trip current - ramp method)• RCD analysis for test of all RCD parameters • Low Ohm and continuity measurement • Insulation measurement up to 1000V (suitable for 690 V industrial mains systems)• Earth resistance measurement with probes and clamp adapters• Voltage and frequency measurement • Current measurement with clamp adapters(optional)• Power and energy measurements• Harmonics measurement for voltage and current upto the 21st harmonics
-
Product
Breaking Force Tester
ZDY-02
-
ZDY-02 Breaking Force Tester is applied for break force test of the ampoule, lipstick, lip cream and other materials.
-
Product
DUT Resistance Tester
-
AllWin Instrument Science and Technology Co., Ltd.
1. This test verfies the integrity of DUT2. The resistance is measured by measuring voltage3. Current is made by distribution
-
Product
Transmission Line Testers
-
GAOTek provides affordable, safe and reliable transmission line testers, digital clamp meters and power meters for sale to the United States, Canada and Globally. A transmission line is a specialized cable designed to conduct alternative current of radio frequency. Transmission lines are used for connecting radio transmitters and receivers with their antenna to distribute signals.
-
Product
UTP Cable Tester
21-8574-00
-
The Lan Cable Tester is consists of unshield RJ45:568A, 568B & USOC. The tester also easy to operate, the user begins testing by connecting. The multiple LEDs showed indication. This Lan Cable Tester is very practical tester can be easily read and correct pin configuration of cable continuity, open, short, miswiring, & no connection.
-
Product
Connection Testers
-
The level of sophistication of the cable harness tester required will depend on the product type, failure modes and integrity required by the eventual customer. There are 3 main types of test that can be applied and this will determine which of our cable harness testers will be most suitable for your product.
-
Product
Comparison Testers
GCH Series
-
Nagman Instruments & Electronics Pvt. Ltd
Budget Solutions. Very Low Maintenance Cost. Compact & Easy to carry for Lab & Field use. Priming Pump with Fine Adjustment Vernier for Incremental Pressure generation. Adjustable Foot.
-
Product
TIM Tester
-
The Analysis Tech TIM Tester 1300 is an automated test system for measurement of thermal impedance and conductivity on thin, thermally conductive materials of the type frequently used for electronic packaging, as well as a wide variety of flexible or rigid solids and semi-liquid or viscous materials. Generally, the TIM Tester 1300 can accommodate samples with high-to-medium thermal conductivity with contact pressures ranging from 10 to 550 psi (70-3800 kpa) and at sample temperature ranging from 15C to 70C.
-
Product
Scratch Tester
-
Scratch testers from Anton Paar are used to characterize film-substrate systems and to quantify parameters such as adhesive strength and friction force by using a variety of complementary methods. This makes scratch testers invaluable tools for the determination of coating adhesion, scratch resistance, and mar resistance in research, development, and quality control.
-
Product
Brinell Hardness Testers
-
Newage Testing Instruments, Inc.
We offer a wide range of rugged, high precision Brinell hardness testers and accessories for your Brinell testing.
-
Product
Digital Igniter Tester
Alpha 4314
-
The Alpha 4314 Digital Igniter Tester is a portable digital ohmmeter which has been specifically designed for ultra-safe resistance testing on explosive devices (i.e. squibs, detonators).
-
Product
Battery Load Tester
Battery Beak
-
Cross the Road Electronics, LLC
The Battery Beak is a battery load tester that is capable of delivering an 18 amp load and measuring a batteries internal resistance, state of charge (SOC), and can determine the overall health of the battery. The Battery Beak supports all battery chemistries but has additional features to determine battery health for both Lead Acid and NiMH chemistries and supports a variety of AmpHour/Voltage combinations.
-
Product
Circular Locus Tester
TF225
-
TESTEX Testing Equipment Systems Ltd.
Circular Locus Tester, to determine surface deterioration and quality of fabrics (wool, chemical fiber, mixed, kitted and woven fabrics). Using an active friction system, fabric is rubbed against a nylon brush and abrasive or an abrasive only under controlled conditions. Results of the test are achieved in minutes. The relative motion of the locus specimen grip and the abrasive platform is a circle with a relative speed of 60+/-1 r/min. The grip offers pressure to the specimen which is adjustable with a tolerance of +/-1%. For added control and safety, the machine is equipped with a self-stop switch.
