Surge Testers
Analyze device performance under a sudden increase of electrical power.
See Also: Hipot Testers, Impulse Winding Testers
-
Product
Memory Tester
SP3000
-
CST is proud to offer a portable stand alone and affordable memory tester, combining DIMM and SODIMM testing capability all on the same universal base unit with optional easy plug-on test adapters.
-
Product
Socket Tester
1945
-
Peaceful Thriving Enterprise Co Ltd
This is a portable 220VAC socket tester to inspect the wiring conditions. The tester also features current variation for simulation of different leaking current. With the current variation, technician is able to test the condition of Ground Fault Circuit Interrupter (GFCI) / Residual Current Device (RCD) easily.
-
Product
Surge Generator
CFL SG 3210
-
SCOPE offers CFL SG 3210, Surge Generator with output of 32kV and 1000 Joules. It is ideal choice for fault location on all types of power cables from LV to EHV. CFL SG Series is equipped with different Protections, Interlocks and Auto-discharge Facility to ensure User Safety during operation. User Friendly controls, adequate form factor, contact free HV terminations makes this CFL SG Series most durable and best-designed sets in the segment.
-
Product
Vector Tester
PVT360A
-
The R&S®PVT360A is a VSG/VSA single-box vector tester optimized for FR1 base station, small cell and RFcomponent testing in production and characterization environments. Two independent signal generatorsand analyzers enable fast parallelized measurements. A frequency range of up to 8 GHz, flexible bandwidth configuration and an optional second TRX channel provide the necessary performance and enable flexible adaptation in a small form factor.
-
Product
Jerking Tester
JLD-10
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.3-2008/IEC60851-3; Inspection standard:JB/T4279.5-2008Used to measure the film adhesion property of enameled round wires with nominal conductor diameter of 1.000mm and below;Built-in small ultra-quiet air compressor would provide power supply and automatic constant pressure;Samples, while being jerked, would not move and slip out;
-
Product
Memory Tester
RAMCHECK
-
RAMCHECK is our most advanced memory tester and is the latest in our product line. Highly modular and user friendly, it redefines the capabilities of an affordable and portable ram checker.
-
Product
Polymer Testers
-
AMETEK Sensors, Test & Calibration
Accurate polymer testing requires dedicated polymer testing instruments. We offer a range of polymer testers for measuring density and intrinsic viscosity (IV).
-
Product
Cable Testers
FiberMASTER
-
FiberMASTER provides optical loss (dB) measurements meeting Tier 1 certification requirements.
-
Product
Function Tester
-
Test device for functional testing of defibrillators, external pacemakers and ECG simulation.
-
Product
Surface Roughness Tester
-
A precision instrument used to evaluate the texture of a surface, determining whether it is rough or smooth.
-
Product
Hipot & Security Tester
-
Safety testers (also called hipot testers) ensure the safe use of test items in different working environments and under different operating conditions. There are a variety of solutions, depending on the tests required to meet the relevant industry standards. Many test units offer a combination of functionality and performance.
-
Product
Modular Testers
-
Modulare adaptronic wiring testers of the NT 700 series designed according to your test requirements. The design in mobile cabinets allows the integration of manifold test functions.
-
Product
Laboratory Battery Tester
-
Compact and versatile, our portable desktop solution integrates Arbin's advanced testing features.
-
Product
8-Position Dissolution Tester
Vision G2 Elite 8
-
The Vision G2 Elite 8 dissolution tester is a versatile performance machine, built with the highest quality components and engineering. The G2 Elite 8’s ergonomic design and workhorse performance make it ideal for automation and extended applications as well as for 8-sample manual testing. The G2 Elite 8 meets and exceeds worldwide standards including compliance with USP, US FDA, ASTM, EP, JP, CE, CSA, RoHS, and 21 CFR Part 11.
-
Product
Optomechatronics Testers
-
T100 is a flying actuator tester designed to calibrate and test any kind of device, module or product with electronic, optical and mechanical functions, using the latest opto, MEMS, sensor, microelectronics, micromechanics technologies.T100 can be equipped with tools and actuators to perform calibration, electrical test, mechanical test, optical test.All on a single machine without any need for additional equipment.It is the ideal tester for production lines with a wide variety of products and frequent entry of new ones.
-
Product
Transformer Bench Tester
KVBT
-
KV Hipot Power Test Equipment Co.,Ltd
Transformer Test System is applied for ex-work and maintenance detecting on various transformers.
-
Product
Relay Tester
PTE-50-CE
-
The reversible 100-VA amplifier can inject up to 50A or 150V with outstanding stability, free of distortions and completely isolated from the power supply. The waveform is synthetized electronically and can generate harmonics from 1st to 7th of the supply’s frequency. Various output ranges are available to maintain the 100VA power throughout the entire settings scale. The system features automatic protections against overload and overheating.
-
Product
Combination Board Tester
-
Qmax Test Technologies Pvt. Ltd.
Combination Board Tester capable of testing highly complex and dense PCBs employing various test techniques on a single platform. It can perform Board Level Functional Test through edge connectors of a PCB, and guided probe diagnostics utility to reliably repair Digital/Analog and Mixed Signal PCBs of various complexities and conventional PCBs. An In –Circuit device test by configuring Pin Drivers to High Current Pin Driver mode and interface to the UUT either through Clips / Probes or nail bed and on board clock disable HW feature are the all time favorite . The in-built high frequency 14bit Analog Driver / sensors synchronized with digital drivers for covering analog / mixed signal devices with high degree of accuracy.
-
Product
High-acceleration Shock Tester
DP-1200-18
-
King Design Industrial Co., Ltd.
The precise-type high-acceleration shock tester can provide all half-sine short wave specification specified in JESD22-B110. To meet them, merely change different shock rubber-pad on shock seat. The wave is complete with high repeatability, able to provide user accurate test result.Conform to different test specs such as JESD22-B110 and IEC spec.High repeatability on consecutive shock; acceleration +/- 10%; run time +/- 15%; speed deviation +/- 10%.Table’s four corner-points uniformity P160mm +/- 10%.Can add spring system to reach the requirement of extra high acceleration specification.Using high-efficiency vibration-absorbing seat pad can block out possible floor resonance and protect the factory structure.Easy in operation; no complicate training course required.Module shock rubber-pads are applied per different standards independently. And the rubber-pad lifetime can be prolonged.
-
-
Product
Keyboard Button Testers
-
Infinity Machine International Inc.
Keyboard Button Testers by Infinity Machine International Inc. - for applications such as keyboard button compression force tester, keyboard durability test machine, adjustable keystroke life-span tester, mechanical keyboard switch tester, computer keystroke tester, button force testing, key stroke force tester for load stroke curve test, rubber keystroke tester, and more.
-
Product
Wire Harness Tester
NX Pro
-
The Dynalab NX Pro Wire Harness Tester is a low-cost, feature-packed, stand-alone continuity tester with a maximum capability of 512 test points. The flexibility of the NX System allows each program to perform multiple tests, display custom messages or sounds, and analyze the results of a test or an input to "decide" which operation to perform next. The NX Pro Tester has 1.3Mb memory capacity for program storage and is compatible with Printers, Scanners, and all other Dynalab NX System accessories.
-
Product
Combustion Leak Tester
AC560000
-
Fast, economical and accurate method to test for combustion gas leaks in head gaskets, cylinder heads and engine blocks. Dual chamber design provides more accurate test results. Test fluid can be used for both gasoline and diesel engines.
-
Product
Vacuum Tester
QCT-2A
-
Changzhou Chanlon Electronic Technology Co., Ltd.
This machine is applied to vacuum cleaner type motor. Its LCD shows all technical data which obtained by industrial control computer, which check and verify the quality of testing stator.
-
Product
Pitot Static Tester
ADSE 746
-
The ADSE 746 caters fully for all aircraft types and the different electrical power supplies. It can be used for testing high performance civil and military aircraft, fixed and rotary wing. Themulti-pressure outlets option can suit themore complex pilot-staticsystems.This Pitot Static tester is designed primarily for flightline use to cover the testing of all barometric and manometric pressure instrument systems. The large touch screen display, with on-screen help, enables all checks to be carried out easily on the flight deck or in the cockpit, by a single operator. The test set is robust and housed in a mobile weatherproof case fitted with tire wheels. An attached bag contains the pressure hoses and electrical cables.
-
Product
Schildknecht Flexing Tester
-
TESTEX Testing Equipment Systems Ltd.
Schildknecht Flexing Tester is designed to determine the resistance of coated fabrics to damage by flexing due to oscillation at 500 times per minute. Schildknecht Flexing Tester complies with ISO 7854, BS 3424, etc.
-
-
Product
Electricity Meters Tester
TE30 Lite
-
Calmet Smart Calibration Devices
Electricity meters tester class 0.02%. Three phase tester of current transformers and analyser of power network quality. It makes possible electricity meters testing on the site or in the laboratory.
-
Product
Torque Tester
CD-100M/10M
-
Ideal for daily inspection of electric screwdrivers. Use conventional joints. Five channels of pass/fail judgment conditions can be saved, and settings can be made simply by switching channels even if the tightening conditions change. 3 times more durable than the conventional model, even with sudden high torque. disassemble the joint due to excessive unwinding .
-
Product
Cable Locators & Testers
-
PeakTech Prüf- und Messtechnik GmbH
This new cable detector consisting of a transmitter and a receiver is suitable for the search of voltage-free and voltage - carrying lines, as well as line interruptions and line tracking of surface and flush-mounted lines, pipe systems and even lines in the ground.
