I²C
A slow Inter-Integrated Circuit bus protocol.
-
Product
I²C/SPI Interface Device
-
The I²C/SPI Interface Device is a master or slave interface for inter-integrated circuit (I²C), or master interface for serial parallel interface (SPI) devices. With plug-and-play USB connectivity, the I²C/SPI Interface Device is a portable solution to communicate with consumer electronics and integrated circuits. The I²C/SPI Interface Device can be physically located more closely to I²C/SPI devices than PCI interfaces, reducing I²C bus length and minimizing noise problems. The I²C/SPI Interface Device supports I²C rates up to 250 kHz and SPI rates up to 50 MHz, and it also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I²C devices or toggling LEDs.
-
Product
Alumel, Type K (°C) Contacts
-
Thermocouple contacts are manufactured from chromel or alumel alloys and are color-coded for easy identification. They are crimp terminated and easily inserted into connector modules and readily removed using a special removal tool.
-
Product
Anemometer, 0.4m/s to 30m/s, -0 °C, 50 °C
72-7595
-
4 in 1 Anemometer, Hygrometer, Luxmeter and Thermometer
-
Product
NI-9218, 51.2 kS/s/ch, 2-Channel C Series Universal Analog Input Module
783362-01
-
51.2 kS/s/ch, 2-Channel C Series Universal Analog Input Module - The NI‑9218 is designed for multipurpose measurements. It offers built-in support for accelerometer, powered sensor, full-bridge, and voltage measurements as well as quarter-bridge, half-bridge, 60 V, and current measurements using measurement-specific adapters. Each channel is individually selectable, so you can perform different measurements on each channel. The NI‑9218 is ideal for creating universal test systems for automotive, off-highway, and data-logging systems.
-
Product
cDAQ-9178, 8‑Slot, USB CompactDAQ Chassis
781156-01
-
8‑Slot, USB CompactDAQ Chassis - The cDAQ‑9178 is a CompactDAQ USB chassis designed for small, portable sensor measurement systems. The chassis provides the plug‑and‑play simplicity of USB to sensor and electrical measurements. It also controls the timing, synchronization, and data … transfer between C Series I/O modules and an external host. You can use this chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The cDAQ‑9178 also has four 32‑bit general-purpose counters/timers. You can access these counters, as well as share clocks and triggers, through two built-in BNC connectors.
-
Product
Hazardous Location Syringe Pump
1000HLf
-
The Teledyne ISCO HLf-Series pumps give you the same accurate, predictable flow and pressure control as our standard D-Series, while conforming to safety standards for use in UL Class I, Division 2, Groups A B C & D, T4 environments. The hazardous location rating is achieved through internal design modifications including the use of brushless DC motors. This approach eliminates the need for purge boxes or other additional safety devices. Wetted materials are compatible with most aqueous and organic liquids, corrosive solutions, heated fluids, liquefied gases, viscous fluids, or slurries and pastes. If needed, optional materials such as Hastelloy C-276 are available on request. The HLf controller has a keypad and LCD, as well as built-in and optional interfaces for computer control and other devices. Programming is easy and flexible, with instant access to menu screens even when the pump is running. This allows you to change operating parameters on the fly.
-
Product
Pneumatic Module, ITA, 5 Position (3/8" Flow)
510108144
-
The 5 Position Pneumatic Modules are made of G10 Epoxy Glass, withstanding temperatures of 140°C. Nomenclature is silk-screened white onto the Modules.
-
Product
Manual Step Attenuator, DC to 18 GHz, 0 to 110 dB, 10 dB steps
8496B
-
The Keysight 8496B dc to 18 GHz manual step attenuator offers exceptional repeatability and reliability. Attenuation is provided in 10 dB steps from 0 to 110 dB. Precision gold-plated leaf springs ensure long life (over 5 million cycles) and very high attenuator repeatability (typically 0.01 dB). To improve measurement accuracy, NIST traceable data (SWR and attenuation) is available as Option UK6. Custom step attenuator/switch combinations are possible. The Keysight 11716A/B/C interconnect kits provide quick connection of Keysight 8494/5/6/7 1 dB and 10 dB step attenuators in series for greater dynamic range with 1 dB steps.
-
Product
NI-9266, 8-Channel C Series Current Output Module
785047-02
-
8-Channel C Series Current Output Module - The NI‑9266 is ideal for interfacing and controlling industrial current-driven actuators. The module has built-in open-loop detection, which generates an interrupt in software when an open loop is detected as well as zeroing outputs to ensure safety and avoid driving actuators at system power on. The NI‑9266 includes channel‑to‑earth ground isolation for safety and noise immunity.
-
Product
16GB R-DDR5 5600 R-Dimm 2GX8 1.1V SAM
AQD-D5V16GR56-SB
-
SAM Original Chip, Industrial Design for Improved Reliability, Compatible with server platform, 30u” golden finger, Operating Temperature: 0°C ~ 85°C.
-
Product
PMC Bus Analyzer / Exerciser
PMC650
-
The PMC650 analyzer provides a multitude of functions to help you analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation and fault generation- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics
-
Product
Miniature LVDT Position Sensors
-
Miniature LVDTs are ideal where reliable measurements are needed in small spaces. With options for venting up to 30,000 psi, and temperature ratings to 400°F (200°C), these LVDTs operate in hydraulic equipment, embedded in robotics, and used in harsh downhole conditions.
-
Product
NI-9870, 4-Port, RS232 C Series Serial Interface Module
779891-02
-
The NI‑9870 adds RS232 serial ports to CompactRIO systems. The serial ports are accessed directly from the FPGA to offer you flexibility in communicating with serial devices. The module has individual buffers on every port that save FPGA space and simplify programming. The NI‑9870 supports standard start bit, stop bit, and handshaking settings. It uses an external power to provide maximum compatibility and reliability under all serial port conditions.
-
Product
Temperature Transmitter
T4211
-
Transducer is designed for temperature measurement at C or F by means of an externaltemperature probe with Pt1000 sensor. Measured values are displayed on LCD display. It ispossible to switch OFF the LCD at all.
-
Product
cRIO-9056, 1.33 GHz Dual-Core CPU, 4 GB Storage, -20 °C to 55 °C, Artix 7 75T FPGA, 8-Slot CompactRIO Controller
786426-01
-
1.33 GHz Dual-Core CPU, 4 GB Storage, -20 °C to 55 °C, Artix 7 75T FPGA, 8-Slot CompactRIO Controller - The cRIO-9056 is a rugged, deployable controller for data acquisition and control applications. It offers Intel Atom dual-core processing, an Artix-7 FPGA, and eight slots for C Series modules. It runs the NI Linux Real-Time operating system with access to the I/O through NI-DAQmx drivers or with the LabVIEW FPGA module. The controller provides precise, synchronized timing and deterministic communications over the network using TSN, ideal for distributed measurements and control. This controller offers one Gigabit Ethernet port, one USB 3.1 host port, one USB 2.0 device port, a trigger line, and a μSD card slot for storing data locally. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
Product
Handheld Oscilloscope
-
Qingdao Hantek Electronic Co., Ltd.
An all-new handheld oscilloscope-Hantek2000 series, it continues the compact and lightweight concept but with a new generation of 3 in 1 multifunction tester: oscilloscope, signal source and multimeter; A small volume of the non-profit grip by a single hand; The suspendingstand was designed to support multi-angle adjustment; Ultra-low-power, Type C charging interface, each 2 hours battery charge allow working one full day or standbytwo months; High-definition color LCD screen display clear and delicate; Minimalist keyboard design simplifyoperation, easy to use.
-
Product
DC/DC Converter 1000 W
CRS-1000-6476-C
-
DC/DC converter with 1000 W from Premium | input ranges 14.4 - 30 VDC | output 48 V | operates in temperatures from -25 to +70 °C | designed according to EN50155
-
Product
DC/DC Converter 2 W
REM2-3.305S
-
DC/DC converter 2 W from Recom | input ranges 3 - 3.6 VDC | output 5 V | operates in ambient temperature from -40 to +95 °C
-
Product
Endurance® High Temperature Infrared Pyrometers
-
The Endurance® Series of infrared pyrometers features rugged and flexible instruments designed to meet the demands of harsh industrial environments and provides continuous visual process monitoring in a wide range of applications and temperatures ranging from 50 to 3200°C (122 to 5692°F).
-
Product
Gauge Type T Thermocouple Wire
W-TW-44
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
Haze Meters
-
Haze meters are referred to as a haze and transmittance measurement machines. They perform both vertical and horizontal sample measurements. Features open measurement area; there's no limit on sample size. It uses different light sources sort of A, C, D65 to quantify haze and transmittance of the test sample. Designed in accordance with ASTM, ISO international standards.
-
Product
Cable Assembly, 37-Pin D-Type, Female to Unterminated With Cut Ends, 2m, HV
A037DF4-C-HA200
-
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Bench Power Supply, Linear, Programmable, 1 Output, 0 V, 60 V, 0 A, 2 A
72-2715
-
The 72-2715 from Tenma is a single channel programmable bench power supply. It is a digitally controlled industrial grade power supply with load for a long time. This compact design power supply has intelligent temperature controlled fan, low noise and low ripple. It also features knob lock function to avoid improper operation. This power supply has load regulation ≤0.01% +2mV (voltage), ≤0.1% +5mA (current) and line regulation of ≤0.01% +3mV (voltage), ≤0.1% +3mA (current). The setting accuracy (25°C ±5°C) is ≤0.5% +30mV (voltage), ≤0.5% +5mA
-
Product
Silicon O/C Content Tester
HS-OCT-6700
-
The HS-OCT-6700 system used to measure the O&C in silicon ingot and wafers. The system is the highest performance FT-IR systems available. While the spectrometer has the power to handle the most advanced research-level experiments, routine analyses are performed just as conveniently. Every facet of the Nicolet FT-IR spectrometer has been engineered to facilitate sample handling, introduce options to scientists, and increase laboratory throughput.
-
Product
DC/AC Inverter 450 W
ODS-750-7287
-
DC/AC inverter with 750 W from Premium | input ranges 77 - 138 VDC | output 120 VAC | operates in temperatures from -25 to +70 °C | approved for EN45545-2 fire and smoke
-
Product
Temperature Measurement IR Sensors & Detectors
ST60 TO-5
-
A single-channel silicon-based thermopile provides lowest cost solutions in a small active area of 0.61mm x 0.61mm in a TO-5 package. Time constant of 18ms with Nitrogen encapsulation gas. Delivers a very low Temperature Coefficient of Responsivity of -0.04%/C. This detector has a very short thermal shock response to ambient temperature change.
-
Product
Flow Control Set Up Using PID Controller
ULP-25O & ULP-25T
-
Unitech Scales And Measurements Pvt. Ltd
Flow Control Setup Comprises of a Orifice with DPT to measure flow Rate. The flow of water is controlled by Control Valve with pneumatic actuator. I to P converter is provided to control the actuator. Rotameter is provided to measure actual flow rate. The system is mounted on a table top model with all necessary piping.
-
Product
K Thermocouple Surface Probe
TP772
-
Surface thermocouple Type "K" probe. °C max: 400. Response time: 3 s.
-
Product
NI-9237, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
780264-01
-
50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The NI‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the NI‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools.
-
Product
NI-9437, 24 VDC to 250 VDC, 8-Channel (Sinking Input), 1 µs C Series Digital Module
783393-02
-
24 VDC to 250 VDC, 8-Channel (Sinking Input), 1 µs C Series Digital Module - The NI‑9437 is well suited for direct connection in rail and power applications along with a wide array of industrial and automotive switches, transducers, and devices with high-voltage input needs. It features ratiometric thresholds that automatically adjust to 2/3 of the user supply voltage.
