Recorders
capture and hold data, authenticating events.
See Also: XY Recorders, Chart Recorders, Fault Recorders, Disturbance Recorders, High Speed Data Recorders, Event Recorders, Transient Recorders, Temperature Recorders, Data Recorders
-
Product
Marine Gravimeter
GT-2M
-
The GT-2M marine gravimeter brings proven design and fully automatic operation to marine gravity measurement. Intelligent Platform Control and 4 programmable filters running simultaneously allow the collection of high quality data on vessels of any size through periods of high sea states. Proprietary software provides real-time relative free-air gravity values at a selectable recording rate for continuous data evaluation.
-
Product
Data Acquisition (DAQ) for R&D and Testing Applications
-
While Memory Hicorders don’t have sampling speeds that are as fast as those of digital oscilloscopes, these waveform recorders can be used to record various types of signals without worrying about potential differences between them and without using isolation amplifiers.
-
Product
Logger with Current Clamp0 to 200A AC
TV-4810
-
As well as recording data the unit has a display that shows what the unit is currently reading. The unit has an IP65 case and features high reading resolution and accuracy, a large memory, a fast offload speed and a low battery monitor.
-
Product
Bench Digital Multimeter, Calibrated D & U, 1 kV, 10 A, 3.8 Digit
72-1015 CAL DU
-
The 72-1015 CAL DU from Tenma is a digital bench type true RMS multimeter. It has auto and manual range options with maximum reading of 5999 counts and 3-5/6 digits which has a unique outlook design. In addition to all the conventional features including DC/AC voltage, current, resistance, diode, continuity test, diode test capacitance, temperature, transistor, max/min, there is a data hold, low battery display, sleep mode, RS232C serial port for easy connection with computer to realize macro recording, monitoring and capture of transient dynamic data, displaying change of waveform during the measurement, providing data and evidence to engineering technicians for scientific research. This meter complies with the standards IEC61010, pollution degree 2, overvoltage category (CAT I 1000V, CAT II 600V) double insulation and CE marked.
-
Product
T3DSO1000/1000A Series Oscilloscopes
T3DSO1000/1000A Series
-
Teledyne Test Tools new T3DSO1000/1000A Oscilloscopes feature two channel and four channel models. The two channel model is available in 100 MHz, 200 MHz or 350 MHz bandwidths, a single ADC with up to 2 GSa/s maximum sample rate, and up to 28 Mpts of sample memory. The four channel scope is available in 100 and 200 MHz models and incorporates two 1 GSa/s ADCs and two 14 Mpts memory modules. When all channels are enabled, each channel has sample rate of 500 MSa/s and a standard record length of 7 Mpts. When only a single channel per ADC is active, the maximum sample rate is 1 GSa/s and the maximum record length is 14 Mpts. For ease-of-use, the most commonly used functions can be accessed with its user-friendly front panel design.
-
Product
Temperature Data Logger
Fresh Tag 1
-
Single trip temperature data logger.* Free from Software uploading. Read the data by mobile phone orcomputer at any time. * PDF readout, irreversible and true recording.*Low power consumption.
-
Product
Battery Analysis Software
-
Battery characteristics vary over time and depend very much on maintenance and the environmental conditions of the specific application. Each installation tends to have its own 'fingerprint'. Capturing and managing this critical operational data has always presented a challenge to facilities managers. Recording and analysing data using traditional pencil and paper methods is both time consuming and prone to error.
-
Product
High Definition MWIR Science-Grade Camera
FLIR X8580™
-
The FLIR X8580 midwave IR camera is designed for scientists and engineers who need to capture detailed imagery of high-speed events, perform custom radiometric measurements, or detect points of failure in composites, solar cells, and electronics. This thermal imaging camera combines 1280 × 1024 HD resolution with fast frame rates and integration times, allowing researchers to record stop motion on fast-moving subjects or rapid temperature changes—whether in the lab or on the test range. With a four-position motorized filter wheel and support for FLIR motorized focus lenses, the X8580 will provide higher quality recordings, save time, and mitigate frustration in dynamic acquisition environments.
-
Product
Dynamic Signal Analyzer & Data Recorder
Spider-20
-
The Spider-20 series of products are compact yet powerful data acquisition and dynamic measurement systems. These units provide four 24-bit precise high-fidelity input channels, and a unique software-selectable tachometer-input/signal-source output channel.
-
Product
Ethernet/LXI digitzerNETBOX 14 Bit High Speed Digitizer - 400 MS/s on 20 Channels, 20 Single-Ended Inputs
DN6.448-20
-
The digitizerNETBOX DN6.44x series allows recording of up to 24 synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
Product
Broadcast Recording And Compliance Logging System
AMR130
-
The Mividi® Broadcast Recording and Compliance Logging System (AMR130) provides a cost-effective solution for broadcast compliance monitoring and logging. It is a Windows PC based system that utilizes GPU encoding for low-cost video transcoding. The software supports stream recording, file management, editing and playback. The recorder takes transport stream input from UDP over IP or ASI interfaces, as well as Internet OTT streaming input using HLS, RTMP, RTSP, and MPEG-DASH protocols. A single system can support continuous recording of 30 streams.
-
Product
Isolation Relays
-
TransData Isolation Relays provide surge protection for energy metering installations by electrically isolating the pulse input/output wiring path to protect electricity meters, network components, energy management systems and recording devices from damage caused by transmitted or induced electrical surges.
-
Product
Battery Internal Resistance Tester
HDGC-3915
-
HD Power Test Equipment Co.ltd
Battery Internal Resistance Tester is designed using the advanced AC discharge measurement method to test accurately voltage and resistance of battery. It is strictly designed to evaluate battery performance, state and life-time, which maintain all stationary power systems including Uninterruptible Power System. Battery Internal Resistance Tester can proceed the measurement in a group and in a single section of battery. With accurate testing of resistance and voltage, it gives an indication of battery capacity and technical status. The measurement data can be read on the instrument display directly. And it can also be uploaded to PC simply by using the USB drive. With the analyzing software, you could not only keep a record of the testing result but also have detailed analyzing for the status of batteries in different testing conditions.
-
Product
ARINC 429 Test & Simulation Interface for PCI Express
PCIe-C429
-
Avionics Interface Technologies
4, 8, 16, or 32 Software Programmable Tx/Rx Channels - Programmable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection • Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B time code encoder/decoder with free-wheeling mode - Application Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
Field Strength Meter
FIM-71 VHF
-
The Model FIM-71 is a portable, laboratory quality Field Strength Meter designed for rigorous field applications. Combining a calibrated half-wave dipole antenna and a highly accurate tuned voltmeter with a range of 140 dB, the FIM-71 is suitable for practically all types of RF emission measurements in the 45 MHz to 225 MHz spectrum. The operator can switch select wide or narrow bandwidth, peak or average value of TV or pulse modulated signals, AM or FM demodulation, and a meter dynamic range of either 20 dB or 60 dB. A dc analog output voltage, proportional to the meter indication, is provided for driving a chart recorder. A leveled output from the calibrating oscillator is available for measuring cable insertion loss, filter response, amplifier gain, and other signal ratio measurements. The 4-1/2 inch, taut band, mirrored scale meter is calibrated in volts and dB for precise measurements in field or laboratory environments.
-
Product
High Speed Communication Board
MS 1712
-
- 12 Channel RS422 Standard Communication interface- 4 Channel Configurable Manchester Bi-Phase Signal communications- 4MBPS configurable baud rate- VIRTEX4 FPGA based design- Hardware Frame formation- Hardware Data validation with START & END frame identification and Checksum calculation for RS422 communication- 1MB DPRAM for PCI interface- Separate set of FIFO's for Transmit and Receive channel- 16 Channels data recording through CF (Compact Flash Storage - Capacity up to 8Gbyte) up to 30min @ 2Mb/sec- Online download through USB interface- Driver interface for Windows2000/XP/VISTA and LINUX OS- 6U size cPCI Board- Hot Swap facility is provided for the live Insertion and removing of the board- 12 RS422 channels in front panel interface using two 25-pin D-Type connector
-
Product
200KHz / 10000Freq.Point LCR Meter
MCH-2816A
-
It has high test frequency of 300kHz and 0.01Hz stepping arbitrary programming, and it has 10mV-2V signal level, all making it meet the precision test requirements of production line quality control, in-coming inspection and lab. Its HANDLER, RS232c interfaces are used for the component automatic sorting system, which provides the conditions for computer telecommunication and test recording. Flexible frequency-response analysis:Due to non-ideal inductor, capacitor and resistor, in order to precisely evaluate the characteristics of one component in one frequency band, MCH2816 could use its signal generation ability with 10mHz resolution to correctly analyze frequency response of the component parameters in any frequency band. In particular, it can do the precise measuring of the resonant impedance of the low-frequency ceramic resonant devices which has wide impedance range.
-
Product
PCIe 16 Bit Multi-purpose Digitizer - up to 20 MS/s on 8 Channels (Single Ended) or 4 Channels (Differential)
M2P.5923-X4
-
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
Product
CMOS Cameras
-
A digital still or video camera that uses a CMOS-based image sensor chip rather than a CCD to record the picture.
-
Product
PCIe 8 Bit High Speed Digitizer - 5 GS/s on 1 Channel, 1.5 GHz Bandwidth
M4I.2230-X8
-
The 9 models of the M4i.22xx-x8 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
Playback And Noise Simulation
-
Our systems make sounds and vibrations perceptible – from the pure, aurally accurate playback of binaural recordings to the realistic reconstruction of sound fields and background noise.
-
Product
Contour Check Shape
-
Contour Check Shape has proven itself in hot rolling of long products and is an essential part of the rolling process in many factories. It checks hot and cold steel profiles with the help of three-dimensional surface reconstruction. Thus, it records geometrical errors due to rolling defects including surface defects like scale seams, shells or roller outbreaks.
-
Product
Data Record Adaptor and Correlator
Joiner
-
nTh Network Technologies to Help
Joiner is a data record adaptor and correlator for mobile and core networks management. The ideal partner for big data architectures with data lakes and analytic applications. Distributed as Docker component, it may be orchestrated in line with the network virtualization function concepts.
-
Product
FastCalXP
-
AMETEK Sensors, Test & Calibration
FastCalXP software allows you to complete a 10 point up and down calibration in less than 3 minutes including printing out a calibration certificate. FastCalXP frees you from manually recording and interpolating gauge readings, which helps reduce data errors.
-
Product
Complete Solution for Developing & Testing Discrete Voltage-Level Interfaces
M8KDiscrete
-
The M8KDiscrete module provides a complete solution for developing and testing discrete voltage-level interfaces. The M8KDiscrete contains control I/O registers that are memory-mapped and may be accessed in real time. The module supports ten programmable I/O discretes that can record or control the external discretes that are connected to it. In addition, the module can record changes in the input discrete with an associated time tag via a built-in FIFO. Output discretes are open collector, capable of handling up to 32V with a maximum sink current of 100 mA each.
-
Product
Thermometer Hygrometer Data Logger
S3120
-
Data logger is designed for record of temperature and humidity. Values are stored to a non volatile electronic memory. Data transfer to the personal computer for further analysis is performed via USB, RS232, GSM or Ethernet interface by means of a proper communication adapter.
-
Product
ARINC 429 PXI Express Test & Simulation Instrument
PXIe-C429
-
Avionics Interface Technologies
16, 32, or 64 ARINC 429 Channels (up to 32 Tx & 32 Rx) - Programmable Tx channel output amplitude - Programmable High/Low Speed Operation - Eight (8) Discrete I/O (Four (4) inputs, and four (4) outputs) - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection • Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B time code encoder/decoder with free-wheeling mode - Application Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
Laser Scanning Oil Film Detector
LO-300
-
LO-300 provides early warning by on-line detection of oil leakage with a laser and a security camera (option)LO-300 uses a laser to scan water surface or the ground to detect an oil film with high sensitivity.LO-300 with camera unit (option) enables to record the video when LO-300 detects the alarm and stores the image captured before and after alarm signal.
-
Product
PXIe-6124, 4 AI (16-Bit, 4 MS/s/ch), 2 AO, 24 DIO, PXI Multifunction I/O Module
780536-01
-
PXIe, 4 AI (16-Bit, 4 MS/s/ch), 2 AO, 24 DIO, PXI Multifunction I/O Module—The PXIe‑6124 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, two 32‑bit counters, and analog and digital triggering. The PXIe‑6124 is ideal for a variety of applications, such as IF digitization; transient recording; ISDN, ADSL, and POTS manufacturing test in the telecom industry; ultrasound and sonar testing; and high-energy physics. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Lux Meters
-
Lux meters are used for measuring brightness in lux, fc or cd/m². Some lux meters are equipped with an internal memory or data logger to record and save measurements. The measurement of light intensity with a lux meter is becoming increasingly important in the workplace due to safety concerns. PCE Instruments' lux meters with data loggers are highly regarded in the industry due to the devices' cosine correction of the angle of incident light.Many lux meters include software for detailed analysis and offer different interfaces for transferring measured data to a computer.
