Modulators
Are devices which varies a characteristic of a repetitious electrical or electromagnetic wave of less than infrared frequency in accordance with a characteristic of an arbitrarily varying information carrying signal.
-
product
Semiconductor & Electronic Systems Test and Diagnostics Services
Reliability Test and Diagnostic services are offered to a wide range of customers that are active as Fabless Semiconductor or Integrated Device Manufacturers, automotive electronics supplier, Telecom and ICT application specialists, Industrial and Medical electronic system manufacturers or in Aerospace and Space applications. Independent high tech test and diagnostic service laboratory. IC and electronic module qualification. ESD and Latch Up testing. Design assessment by HALT/HASS. Failure and construction analysis.
-
product
PXI Battery Simulator Modules
These PXI battery simulators are designed to simulate the power supplies of portable battery powered equipment and the single cell (model 41-753) is particularly suitable for cell phone testing. These modules can source current to simulate a battery supply or sink current to simulate a battery under charge.
-
product
12-Channel VME Current Loop/Process Control I/O Module
V220
The V220 is ideal for driving and sensing transducers in computer or PLC-based control systems. It can also be used to simulate complex industrial processes to control systems under development and certification.
-
product
SHB12X-B12X, 73-Pin, Male InfiniBand to 73-Pin, Male InfiniBand, 100 Ohm, Shielded LVDS Cable 2m
192344-02
The SHB12X-B12X LVDS Cable connects the 12X InfiniBand connector on PXIe-656x LVDS instruments or some NI 658x LVDS Adapter Modules for FlexRIO with other NI accessories such as the SMA-2164 to break out cable signals for direct access. It is a shielded, 100 ohm cable that is offered in various lengths.
-
product
PXI 10A Power Multiplexer, 5-Bank, 6-Channel
40-661A-005
The 40-661A-005 is a single pole, 5-bank, 6-channel PXI power multiplexer module, suitable for switching inductive/capacitive loads up to 10A with 125VDC/250VAC hot switching and 400VDC/250VAC cold switching. The multiplexer is available in 8-bank 4-channel, 5-bank 6-channel, 4-bank 8-channel, 2-bank 16-channel and 1-bank 32-channel formats. Also, 4-bank 4-channel, 2-bank 8-channel and 1-bank 16-channel half density configurations are available.
-
product
The USRP-2920 Teaching Bundle
781908-01
The USRP-2920 Teaching Bundle helps students experiment with real-world signals using LabVIEW software and USRP-2920 receivers. - The USRP-2920 Teaching Bundle is a hardware and software bundle that includes two USRP (Universal Software Radio Peripheral) Software Defined Radio Devices, the LabVIEW Modulation Toolkit software add-on for LabVIEW, and turnkey courseware. The bundle also includes components of a lab station designed to help students gain hands-on experience with a live communication link between two USRP Software Defined Radio Devices.
-
product
PXI-7951, Virtex-5 LX30 FPGA PXI FPGA Module for FlexRIO
780560-01
Virtex-5 LX30 FPGA PXI FPGA Module for FlexRIO—The PXI‑7951 provides flexible, customizable I/O for LabVIEW FPGA. It includes 132 single-ended I/O lines configurable as 66 differential pairs. You can pair the PXI‑7951 with FlexRIO adapter modules that offer high-performance analog and digital I/O. Together, the two modules create a reconfigurable instrument that you can program with LabVIEW FPGA software.
-
product
Facilities Module
FM002A
The FM002A is a facilities module that provides a range of common facilities for all Zero Two control modules housed in the chassis.
-
product
VDI Millimeter-Wave Frequency Extension Modules for PXA, MXA, EXA Signal Analyzers
These modules offer low conversion loss and excellent noise figure. Standard features include dual operating modes. First, the module can function as a high performance down-converting mixer. The second operating mode functions as a block down-converter with a broadband IF up to 20 GHz. Power to the module is provided via an included external DC power supply. These frequency extenders minimize conversion loss by multiplying and amplifying the LO signal internally, thus taking advantage of the benefits of low harmonic mixing. This architecture also preserves the X-Series precision frequency resolution and low phase noise, extending those qualities into the millimeter and sub-millimeter bands.
-
product
Sine Filters
Sine Wave Output Filter Modules provide satisfactorily smoothed sinusoidal waveform with low residual ripple form square waveform with high voltage spikes, present at the output of motor drives.
-
product
PXI/PXIe Microwave Relay, Dual SPDT, 18GHz, 50Ω, SMA, External Termination
40-781A-122
The 40-781A-122 (PXI) and 42-781A-122 (PXIe) are dual SPDT 18GHz microwave relay modules with external terminations. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50GHz in 50Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
product
Generators
Linear Frequency-Modulated Signal Generator
The Software Signal generator allows to produce frequency modulated signals with linear sweep at the DAC output.
-
product
PXI 2 Amp Multiplexer, Single 8-Channel, 8-Pole
40-635A-004
The 40-635A-004 is a single 8-channel, 8-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
product
PXI/PXIe Very High Density Multiplexer, 5-Channel, 32-Pole
40-675B-002-5/32
The 40-675B-002-5/32 (PXI) and the 42-675B-002-5/32 (PXIe) are 5-channel, 32-pole multiplexers and are part of our range of very high density low cost multiplexer modules. These modules are suitable for signal routing in high channel count ATE and data acquisition systems. They use high quality electromechanical signal relays allowing each channel to switch current up to 1 A at 150 VDC/100 VAC. Connections are made via a front panel 200-pin connector.
-
product
10 Gb/s SFP/SFP+ Evaluation Board
EV-SFP-171
The purpose of this SFP+ evaluation board is to provide the designer with a convenient means for evaluating SFP+ fiber optic transceiver such as 10 Gb/s(up to 16 Gb/s) SFP/SFP+ transceiver compliant with ANSI Fibre Channel FC‐PI‐5 for high speed electrical and optical specifications. This board provides SMA connectors for high speed TX and RX signals. The low speed control signals such as Tx_Fault, Rx_LOS and Rate_Selects can be controlled by using on board switches and test points. A connector for 2 wire serial interface to the module is also provided.
-
product
PXI Dual Bus 74-Chan 2A Fault Insertion Switch
40-190B-002
The Dual Bus, 74 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally closed through relays, so in the default state, there is a path between input and output for all signal channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
product
Rack - Touch Display on Swivel Arm
OTP2-Modul-Nr042
The module is for mounting on a rack, such as the midi or maxi rack. The extension with the module can create new possibilities for your test system.
-
product
Tool, Extraction, QuadraPaddle, ITA
910110111
Tool, Extraction, QuadraPaddle, ITA - used to remove the ITA QuadraPaddle contacts from the module.
-
product
sbRIO-9236, Non-Enclosed, 10 kS/s/channel, 350 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module
781580-01
Non-Enclosed, 10 kS/s/channel, 350 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module - The sbRIO‑9236 measures dynamic strain on all channels simultaneously, allowing for synchronized, high-speed measurements. This capability is important for applications, such as impact tests, that require comparison across many channels at a particular instant in time. The sbRIO‑9236 includes built-in voltage excitation for quarter-bridge sensors. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. Non-enclosed modules are designed for OEM applications.
-
product
High-Voltage PXI Multiplexer
These high-voltage PXI multiplexer modules provide solutions for applications that need to switch voltages up to 1000V. Our model 40-320 modules are suited for hot or cold switching applications up to 10W and 0.5A with a rating of 13mA at their maximum operating voltage. Our model # 40-331 modules can switch up to 1000V and also have a hot or cold switching current rating of 5A.
-
product
EMC Test Systems
The sum of EMC is not necessarily equal to its parts; any modular electronic device from a complete aircraft down to a mobile phone needs to meet EMC requirements for the device itself, even if all the individual modules are compliant. For the enormous range of types of modular device requiring EMC test, R&S offers extremely flexible and scalable EMC test systems; practically as modular as the devices under test.
-
product
Connector, 104-Pin D-Type Male, Solder Bucket, 5A
92-960-104-M
This 104-pin male D-type connector allows users to create their own cable assemblies. Cable connection is via solder buckets - supplied without backshell. This connector is not compatible with Pickering modules that use the 104-pin D-type connector.
-
product
PXI-5671, 2.7 GHz RF Vector Signal Generators
779079-04
2.7 GHz, Digital Upconverter Included, PXI Vector Signal Generator—The PXI‑5671 features quadrature digital upconversion, which reduces waveform download and signal generation time. It is a general-purpose vector signal generator that can generate standard modulation formats such as AM, FM, PM, ASK, FSK, MSK, GMSK, PSK, QPSK, PAM, and QAM. The PXIe‑5671 delivers a highly flexible and powerful solution for scientific research, consumer electronics, communications, aerospace/defense, and semiconductor test applications as well as emerging areas including software-defined radio, radio frequency identification (RFID), and wireless sensor networks. For specific communications standards, you can use various software add-ons to generate modulated signals according to standards such as WCDMA, DVB‑H, and ZigBee
-
product
human body vibration module
Human and Whole Body Vibration TestingThe human and whole-body vibration module tests and measures the effect of vibration on the human body. The extracted parameters allow the simple assessment of the injuries risk for workers, exposed to constant vibration. Our solution supports the whole-body and hand-arm vibration measurement are supported according to all relevant international standards - ISO 5349, ISO 8041, ISO 2631-1 and ISO 2631-5.
-
product
Bench-Top & Shop Loader Solutions
Avionics Interface Technologies
To satisfy ARINC 615/615A data loader requirements in system engineering labs, avionics system manufacturing, and maintenance depot applications, AIT provides data loader software that can be used together with AIT’s full line of ARINC 429, ARINC 664, and Ethernet interface modules and integrated into a variety of host desktop PC systems and ATE environments. The F-SIM-LDR-615 software provides ARINC 615-3/4 data loader support and is compatible with all of AIT’s ARINC 429 interface modules. The F-SIM-LDR-615A software application provides ARINC 615A-1 /2/3 data loader support over Ethernet and ARINC 664 networks and is compatible with all of AIT’s ARINC 664/Ethernet interfaces modules. The F-SIM-LDR-615 and F-SIM-LDR-615A software products include both graphical user interface (GUI ) data loader applications and command line data loaders which are scriptable and can be called from shell scripts, batch files, and python for support of automated load operations.
-
product
PMC-XM
The PMC-XM is intended for use in situations where the user wants to control the design. PMC-XM has two FPGA devices built in. The first device takes care of the PCI interface, DMA etc. The second device [Virtex XC4VSX35-10] is for the user application. The Transition Module [XM] is attached to the Virtex device.
-
product
RMS Responding Power Detectors
Recognized as the pioneer and leader in RF detectors, Analog Devices offers a broad portfolio of high performance logarithmic amplifiers and TruPwr™ rms responding detectors. ADI logarithmic amplifiers measure signals up to 100 dB dynamic range, from dc to microwave, and accuracies of ±0.2 dB, and are well-suited for both RSSI and transmit power level detection. The TruPwr rms detectors address the challenge of measuring complex waveforms found in spread spectrum CDMA/W-CDMA and higher order QAM modulation systems and provide an accurately scaled dc voltage, which is the rms equivalent of the input waveform.
-
product
100 Pin Micro-D Cable, Male to Male, 1m 2-56 UNC Screwlocks, Metal Shell
A100SMR-100SMR-9A100
This 1m long male to male 100-Pin SCSI Style Micro-D Cable Assembly is constructed from 7/36 (28 AWG) Tinned Copper twisted pair wiring with Polyolefin insulation to minimise crosstalk. Screwlocks are provided to secure the connectors to their associated products. This cable assembly is suitable for use with Pickering BRIC modules that use the 100-pin Micro-D connector.
-
product
32 Channel Relay Output Switch
DP-VME-4224
DP-VME-4224 is a 32 Channel Relay Output Switch. Applications for this module includes hardware simulation, digital simulation, high-reliability systems, and automatic test equipment, and relay output for soft PLCs.
-
product
PXI/PXIe MEMS Optical MUX, Single 2-Channel, Single-Mode, 9/125 Fiber,
40-855A-312-HI
The 40/42-855A-312-HI is a PXI/PXIe 2-channel multiplexer with MU connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
