Data Acquisition
senses the physical, represented as an analog signal, that is then converted to digital data. Also known as: DAQ
See Also: Data Acquisition Systems, PCI Data Acquisition, DAQ, Digitizers
-
Product
Portable Data Acquisition & Analysis System
LapCAT III
-
# 4, 8, or 16 channels# 1 MHz aggregate 12 bit sampling. Resolution is 0.024% of full scale# 13 recording durations, user selected: 132 msec to 1320 sec# Digital Triggering from any channel, with +/- slope or window# 6 full scale gain ranges, user selected: 0.4, 1, 2, 4, 10, and 20 volts full scale - with a 10mV/g accelerometer these equal 40g, 100g, 200g, 400g 1000g and 2000g full scale - higher or lower ranges by different sensor selection
-
Product
Data Acquisition Processor Board
DAP 5200a
-
The DAP 5200a model brings many more real-time data acquisition and control applications within the scope of Windows systems. Its onboard 400 MHz processor substantially increases the real-time processing power of the top end of the DAP line. Real-time processing functions include smoothing, filtering, FFT, PID control, and responding to alarm conditions;
-
Product
Data Acquisition Software
-
GaGe provides a powerful and easy-to-use PC oscilloscope software application, GaGeScope, for use with CompuScope digitizers without the need for any programming as well as a complete library of software development kits (SDKs) for C/C#, LabVIEW, and MATLAB for custom software application development.
-
Product
Data Acquisition - 3U 3-Slot
DAQ-33CP0G
-
is a preconfigured rugged system with a high-performance, low power ARM® Cortex®-A9 processor. It is ideally suited to support a multitude of military/aerospace data acquisition applications that require high-density, multichannel programmable ARINC 429/575; Dual-Redundant, Quad Channel MIL-STD-1553B; CANBus (2.0 A&B or J1939); A/D Conversion; RTD Measurement; RS-232/422/485 Serial Communications Dual-Port Gig-E Ethernet.
-
Product
High Speed Data Acquisition
-
All systems can be set up in two types of aluminum chassis. These are the conduction cooled rugged 3U VPX chassis “Crosswind 600” and “Desert Gecko” . Ruggedized and sealed to IP65. These units can use void fillers and GORE brand vents depending on the deployment environment.
-
Product
Data Acquisition Module for Embedded Systems with IO60 expansion
IO60-M410
-
WINSYSTEMS’ IO60-M410 is a reliable data acquisition module for embedded systems with IO60 expansion featuring 24 GPIO (General Purpose Input-Output) tolerant to 30 V DC. Activity LEDs indicate device communication and DAC fault. WINSYSTEMS can provide custom configurations for OEM clients. Please contact a Applications Engineer through our contact page for details.
-
Product
USB Modular Data Acquisition
-
The Keysight USB Data Acquisition (DAQ) family gives you the choice and flexibility to create standalone or modular solutions that expand and evolve according to your test requirement needs. Whatever your configuration, setup is easy with high-speed USB 2.0 connectivity: just plug the device into your PC and launch the bundled software.
-
Product
USB to RS-422/RS-485 Converter
ND-6530
-
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
Product
High Performance Data Acquisition
PMC-AD8
-
The PMC-AD8 module provides a high performance dataacquisition subsystem. There are (8) eight 200 KSPSADC’s for maximum performance. The Local DSP can beused to simply move data samples to the PMCbus or canprovide processing functions such as limit checking, FFT’s,digital filtering, etc. Software can be downloaded to theDSP via the PMC interface. Instrumentation amplifiersprovide over-voltage protection and gain on a per channelbasis. The PMC-AD8 can also accept external scan andtrigger signals from a front panel connector.
-
Product
Torque Data Acquisition Software
-
SW-1SV-USB data acquisition software is for all Cedar torque instruments.Force Recorder is compatible with the new HTGS & HTGA digital torque testers.
-
Product
Data Acquisition (DAQ) And Real-time Control Systems
-
Our data acquisition devices are capable of storing hundreds of analog and digital channels at full speed while allowing in parallel data to be sent out in real-time to any 3rd party EtherCAT master controller. We have brought the worlds of data acquisition and real-time control closer together which will save you time and money in a big way.
-
Product
USB Powered, 4 channel, 24-bit Data Acquisition System
DATS-solo
-
The DATS-solo is a pocket-sized, ultra portable, high quality, 24-bit data acquisition system. The fully integrated DATS software provides options for acoustic & vibration testing, rotating machinery analysis, NVH tests, hammer impact analysis, resonance testing and modal analysis.
-
Product
Daqarta v5.10 Data AcQuisition And Real-Time Analysis
-
New Fcal option allows any Windows sound card to measure DC values like temperature or pressure using simple external circuits you can build yourself. Or, measure MHz frequencies with a simple prescaler. DAQARTA v5.10 turns your Windows sound card into a precision laboratory instrument, loaded with advanced features. Put your sound card to work!
-
Product
Pre-Configured Data Acquisition Systems
Series 6800
-
Based completely on the Series 6000 hardware and software platform, Series 6800 is a turn-key system pre-configured for specific measurement types and environments. Systems are available for Strain/Bridge, Voltage/IEPE, Thermocouple and packaged for laboratory or portable applications. Systems range in channel count from 8 to 128 channels and can be easily expanded, should test requirements change. Included PI660 turn-key software helps facilities focus on testing, not developing software. If you don’t see a configuration that fits your application, we can build a system specific to your needs.
-
Product
PCI Data Acquisition Boards
ADDA14-100DMA Dual 14-bit A/D + Dual 14-bit D/A, 25 MS/s
-
Model ADDA14-100DMA contains two simultaneously sampling 14-bit A/D converters and two simultaneous 14-bit D/A converters, and can transfer data directly into host system memory at up to 100 MB/s in 64-bit PCI slots.
-
Product
Data Acquisition DSP based 16 channel
-
The CPCI-AD8/16 module provides a 3U high performancedata acquisition subsystem. There are (8) eight or (16)sixteen 100/200 KSPS ADC’s for maximum performance.The Local DSP can be used to simply move data samplesto the CPCI bus or can provide processing functions suchas limit checking, FFT’s, digital filtering, etc. Software canbe downloaded to the DSP via the CPCI interface.Instrumentation amplifiers provide over-voltage protectionand gain on a per channel basis. The CPCI-AD8/16 canalso accept external scan and trigger signals from a frontpanel connector
-
Product
SBC with E3940 CPU and Data Acquisition
SATURN
-
SATURN combines a feature-rich Atom-class processor-based SBC with a professional-quality industrial analog and digital data acquisition subsystem and flexible I/O expansion in a single board designed for rugged applications.
-
Product
Data Acquisition & Analysis
-
Avionics Interface Technologies
We provide fully integrated avionics data bus and high speed network analyzer and data acquisition systems. Combining our extensive product catalog of Avionics interface modules, and our easy to use Analyzer software applications, with our Engineering Expertise, we are able to satisfy a wide range of avionics network data capture and analysis requirements with our COTS products or with customized solutions.
-
Product
Data Acquisition Mainframes
-
Flexible, modular Data Acquisition system with high performance scanning 6.5 digit DMM. 5 slot mainframes and modules for customized data acquisition solutions including temperature, resistance, current and voltage measurements
-
Product
16-CH 16-Bit 250 KS/s Simultaneous Sampling DAQ Cards
PXI-2022
-
ADLINK"s PXI-2022 is a simultaneous-sampling multi-function DAQ card to meet a wide range of application requirements for PXI bus computers. The device can simultaneously sample 16 AI channels with differential input configurations in order to achieve maximum noise elimination.
-
Product
Data Acquisition Conditioner
D4
-
The Model D4 Data Acquisition Conditioner is a portable, USB-powered precision instrument for use with resistive strain gages and strain gage-based transducers.
-
Product
Complete Data Acquisition System
ScopeLogicDAQ
-
ScopeLogic - complete data acquisition system - consists of Digital Oscilloscope and Logic Analyser. This small instrument is making the accurate analysis of complex analog-digital signals possible - thanks to simultaneous sampling finding relationship between these signals is easy. The user is able to simultaneous use 16 digital channels and 2 analog channels with standard scope probes.
-
Product
Data Acquisition Devices
-
Our data acquisition and encoding systems provide significant performance in reception, signal conditioning and encoding of all types of signals while used in missiles, airborne vehicles, mobile ground-based testing and other platforms that require ease of operation, flexibility, ruggedization and small packaging.
-
Product
Multifunctional Data Acquisition Systems
MS1201
-
This system used for multi-purpose applications such as data acquisition and Automatic Test Equipment. ATE Computer has ISA Bus based eleven slots with inbuilt power supply. Micro Processor board or USB Controller is used to drive the back plane.
-
Product
Data Acquisition Card
-
The Elsys DAQ / data acquisition cards are high precision and high resolution digitizers with complex trigger capabilities, a continuous data acquisition mode, differential or single-ended inputs, digital marker inputs as well as an optional integrated ICP/IEPE supply for piezo sensors.
-
Product
Chart Recorder & Data Acquisition
MRC7000
-
The MRC7000 Recorder/Controller is a microprocessor based circular chart instrument capable of measuring, displaying, recording and controlling up to two process variables from a variety of inputs. Record and control functions, alarm settings and other parameters are easily configured via the keys on the front cover and self-prompting displays. All user entered data can be protected against unauthorized changes via the MRC7000 Enable Mode security system.
-
Product
Computer Automated Data Acquisition
System 471
-
The NEFF System 471 (S471) DAS is a complete moderate-speed DAS for use in computer-based applications. The S471 is designed primarily for computer automated data acquisition in test facilities, laboratories and industrial plants or wherever a moderate-speed, high accuracy DAS operating in high common-mode voltage environments is required.
-
Product
Data Acquisition Software
TranAX 4
-
TranAX 4 is the universal data acquisition software from Elsys designed for the TPCX/TPCE data acquisition cards and the turnkey TraNET data acquisition instruments.- Measurement Configuration- Data Visualisation- Post Processing- Math. Calculation- Report Generation- Excel Export- Measurement Automation
-
-
Product
Data Acquisition Hardware: USB
-
Ease of connection, low cost and good performance are key to our USB product range.
