Attenuators
Reduces the amplitude of a signal without appreciably distorting its waveform.
See Also: Filters, Circulators
-
Product
RF Attenuators
-
Amphenol RF offers a growing Attenuator product line to meet your attenuation needs. Amphenol RF attenuators are designed to offer flat attenuation over the designated frequency range and feature a microwave grade resistor that consistently reduces power. Hex flats on the body allow this attenuator to be easily torqued to the mating connector.
-
-
Product
Voltage Variable Attenuators
-
Macom Technology Solutions Holdings Inc.
Voltage Variable Attenuators (VVA) from MACOM offer the ability to control the attenuation level relative to a voltage. Attenuation range is up to 30 dB covering frequency as high as 45 GHz. VVAs feature excellent return and insertion loss along with high IP3 in small SMT packages.
-
-
Product
Fixed Attenuators
-
In circuits are used to lower voltage, dissipate power, and to improve impedance matching. In measuring signals, attenuator pads or adapters are used to lower the amplitude of the signal a known amount to enable measurements, or to protect the measuring device from signal levels that might damage it.
-
Product
Attenuators
-
CAES offers a full range of RF Attenuators for your designs including analog and digital PIN Diode as well as Switched-bit Attenuators.
-
Product
Waveguide Tunable Attenuators
-
*Low Insetion Loss*Full Waveguide Band Coverage*Precise Adjustment*High Maximum Attenuation
-
Product
Optical Attenuators
-
Guilin GLsun Science and Tech Group Co., LTD
Optical Attenuators by GLSN
-
-
Product
Attenuators
-
A passive electronic device that reduces the power of an electrical or optical signal without significantly distorting its waveform.
-
Product
Attenuators & Loads
-
*High power handling 100W with a wide range of available attenuation values*Very low PIM <- 160 dBc with excellent return loss performance*Support for 7-16 or 4.3-10 connectors and optional 19 inch rack mount kit*Designed and produced to ISO 9001:2008 certification standards for reliability and quality
-
Product
Variable Optical Attenuators
Attenuator
Fast attenuation speed with low insertion loss and built-in power monitoring. Operates in fixed attenuation or constant output power modes and supports SMF, MMF and PMF.
-
Product
RF Attenuators
-
Home > Products > Test and Measurement > AttenuatorsBird - The RF ExpertsRF AttenuatorsBird manufactures a broad spectrum of devices from 2 W to 4000W. Our resistive product portfolio includes air-cooled, water-cooled, oil-dielectric, convection cooled, and conduction cooled RF attenuators with a wide range of connectors and attenuation values.
-
-
Product
Digitally Controlled Programmable Attenuators
-
Broadband frequencies ranging from 30 MHz to 40 GHz. High attenuation levels up to 60 dB. PIN diode designs exhibit extremely fast attenuation step switching performance. Attenuation step size ranges from 0.03 dB to 1 dB. Programmable attenuator control bit sizes range from 5 to 10 bits. Models powered and command controlled via 15 pin female Micro-D socket or USB interface.
-
Product
Fixed Attenuators
-
A fixed 1 dB attenuator from Pasternack. This 1dB attenuator is an in-line, resistive PI attenuator pad design. Our coaxial 50 Ohm attenuator is manufactured to precise RF / microwave industry specifications.
-
-
-
Product
Fixed Attenuators
-
The Analog Devices family of wideband, fixed value, 50 Ω matched attenuator products offers relative attenuation levels that range up to 20 dB. Our products are ideal for microstrip, hybrid, and multichip module applications that require extremely flat attenuation and excellent VSWR vs. frequency.
-
Product
Attenuators
-
Optical attenuators reduce the intensity of transmitted light uniformly across the spectrum. Applications include preventing too much light from overloading a receiver.
-
Product
Voltage Variable Attenuators
-
Voltage variable attenuators (VVAs) that offer up to 60 dB of attenuation across a broad range of frequencies from 400 MHz to 18 GHz. These voltage variable attenuators are frequently used in applications such as electronic warfare, instrumentation, point-to-point and point-to-multipoint radios, fiber optic and broadband telecom, microwave radio and VSAT, military radios, radar, ECM, SATCOM and sensors, and R&D.
-
Product
Waveguide Variable Attenuators
-
A variable attenuator from Pasternack. This SMA microwave attenuator is a continuously variable attenuator design.
-
Product
Fixed Attenuators
-
ZTS provides 2 to 1000 Watts fixed attenuators with many types of connectors to choose from, maximum frequency would reach 67 GHz, we also provide custom or calibrated service as per your request.
-
Product
Coaxial Attenuators Set
11582A
Attenuator
The Keysight 11582A contains a set of four 8491B attenuators 3, 6, 10, and 20 dB furnished in a handsome walnut accessory case. The Keysight 8491B are type-N connectors with a maximum frequency of 18 GHz. This set is ideal for calibration labs or where precise knowledge of attenuation and SWR is desired.
-
Product
Voltage Variable Attenuators
-
a High Reliability Low Noise Voltage Controlled Oscillator (VCO) which covers a 10 MHz to 20 MHzfrequency band with a voltage tuning range from 0V to 20V. This design features exceptional phase noise performance of -120dBc/Hz @ 10 kHz offset. Supply Voltage is +15V with a generated output power level of +10 dBm and 2nd harmonic output of-11 dBc typical. The assembly is RoHs compliant and available in a compact 0.5 inch SMT package with an industry standardmounting footprint. The bottom surface is copper clad with 2-5 micro inches of immersion Gold over 150 - 250 micro inchesof Electro less Nickel which makes it resistant to oxidation for ease of soldering. The VCO operates over a temperature rangeof -40°C to +85°C and is designed to meet a variety of MIL-STD-202 test conditions including Humidity, Shock, and Vibration.
-
Product
Variable Optical Attenuators
-
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
Joinwit Variable Optical Attenuators
-
Product
Programmable Attenuators
-
JFW offers 50 Ohm and 75 Ohm programmable attenuators with either relay or solid-state designs. 50 Ohm Relay Step Attenuators, 50 Ohm Solid-State Step Attenuators (TTL), 50 Ohm Solid-State Step Attenuators (USB), 75 Ohm Relay Step Attenuators, 75 Ohm Solid-State Step Attenuators, Analog Programmable Attenuators, High Power Solid-State Step Attenuators.
-
Product
Step Attenuators
-
A stepped attenuator from Pasternack. Our BNC attenuator is a RF step attenuator design. This 50 Ohm manual step attenuator is precision manufactured to RF and microwave industry specifications.
-
Product
Variable Optical Attenuators
-
A fiber optic variable attenuator is used to reduce the power level of an optical signal in fiber optic communications.
-
Product
Programmable RF Attenuators
-
The AD-USB R3 is AdauraTech’s latest design in the AD-USB series of programmable RF attenuators. Combining all the best features of the previous models, the R3 is the new series flag ship. With a completely custom machine aluminum enclosure, the R3 boasts 95dB of attenuation. The addition of Ethernet allows EASY implementation into the most modern of test setups by allowing network control via HTTP web interface or direct Telnet while the USB port powers the device and allows for serial communication.
