Reactive Load Banks
Provide both lagging and leading power factor loads.
See Also: Load Banks, AC Load Banks, DC Load Banks, Inductive Load Banks, Resistive Load Banks
-
Product
48V / 300 Amp Load
BD18-48P-24/12
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 12V, 24V and 48V Battery systems and isextremely cost effective.
-
Product
High Speed Load Cell Test Interface
LCIC-4CH
-
Industrial Measurement Systems Ltd.
The latest stand-alone controller model: LCIC-4CH, was specially designed to fit portable wheel and axle scales for determining the weight of trucks or heavy vehicles either in static mode or in motion, with very high accuracy and very friendly to operate. The In-motion speeds up the weighing process and allows weighing a truck without the need to stop.In the last 16 years, our stand-alone High-Speed weighing-in-motion controller model: LCIC-WIM was sold all around the world and as for today, thousands are being in use when among our customers are some well known weighing manufacturers.Most of our customers around the world are scale manufacturers or integrators that were able to offer the market the most advanced WIM scale with very short time to market and minimum R&D expenses.
-
Product
DC Electronic Load
3110 Series（250W~700W）
-
Each 3110 Series stand-alone load has its own control and display panel, CC / CR / CV / CP/ Dynamic modes, also can be controlled intranet via RS232 and USB interface.
-
Product
Battery Load Tester
MD4260
-
Test capabilities: Battery voltage, battery cranking, battery charging volts and good/bad battery test. Test batteries on and off the car in just 30 seconds. Heavy duty copper-plated clamps. Internal loaded unit with a 100-amp load capacity. Load safety switch to prevent arcing. For 6- and 12-volt batteries.
-
Product
Structural Load Monitoring
SLM
-
Since 2001 ITM has installed structural strain based monitoring systems in the pulp & paper and energy generation industries. For these systems, our engineers and field service technicians turn structures into measurement instruments (load cells). Load outputs from the structural load cells are monitored and published by a realtime controller to its local interface or network historians and HMIs.
-
Product
Bending Beam Load Cell
-
Futek Advanced Sensor Technology, Inc.
Are the best fit for many measuring tasks. Here, the signal, on principle, depends on the bending moment.
-
Product
Digital Roller Brake Tester for Cars and Vans up to 4.0 T Axle Load with 2 x 4 kW Drive Motors and Max. Track Width of 2,200mm
C_MBT C 4.0 W220 | VP 210156
-
Maschinenbau Haldenwang GmbH & Co. KG.
Digital roller brake tester for cars and Vans up to 4.0 t axle load with 2 x 4 kW drive motors and a max. track width of 2,200 mm.Particularly suitable as stand-alone tester or as part of car reception and diagnostic test lanes with high vehicle throughput and increased loads.
-
Product
Through Hole/ Donut Load Cell Compression Only
THA SERIES
-
Our THA Series through hole donut load cells offer an outside diameter of 1.00 inches and up to two different through hole diameter options per capacity range. These load cells are manufactured from heat treated 17-4 ph stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial environments.
-
Product
Inductive Load Tester
4602-LV
-
There is a tendency that MOSFET has Low On Resistance so that it demands that Inductive Load Tester to have higher forcing current for measurement. The forcing current is limited by forcing voltage with previous test method. Thus it becomes difficult to test this kind of middle power range devices.
-
Product
Load Cell Transducer
-
Unitech Scales And Measurements Pvt. Ltd
Force can be measured by different methods, one of the most effective and accurate method is by using strain gauge based load cells. Four Transducer class strain gauges are bonded on the specimen and are connected in the form of Whetstone Bridge. The specimens are of different types depending on the requirement such as S, column, beam, ring, shear beam, binocular etc. UNITEH’S Load Cells are used for wide applications rite from commercial weighing scale to industrial process controlling, R & D applications and educational institutions. UNITECH’S manufacture load cells from 1Kg to 100Tons for compression or tension or universal (Compression and tension) applications. We also undertake custom built load cells for specific requirement and for OEM users.
-
Product
AC Load Bank
-
PC software controls offer advanced load profile solutions and model options range from small, portable, low-power units, to high-power indoor or outdoor permanent load solutions.
-
Product
Digital Roller Brake Tester for Cars and Vans up to 3.5 T Axle Load with 2 x 3 kW Drive Motors and Max. Track Width of 2,500mm
C_MBT C 3.5 W250 | VP 210153
-
Maschinenbau Haldenwang GmbH & Co. KG.
Digital roller brake tester for cars and vans up to 3.5 t axle load with 2 x 3 kW drive motors and a max. track width of 2,500 mm.Particularly suitable as stand-alone tester or as part of car reception and diagnostic test lanes for larger vehicles such as SUVs, off-roaders or vans.
-
Product
PXI 4 Banks of 40 Channel 1 Pole MUX
40-615-022-4/40/1
Multiplexer Module
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
Product
Oscilloscope, 350 MHz, 2 GS/s interleaved, 4 CH, 200 Mpts/Ch DSO, Fully Loaded with 10.1" Color Display
T3DSO2354HD
Oscilloscope
The T3DSO2000HD series of Bench Oscilloscopes feature 4-channel models with analog bandwidth options of 100 MHz, 200MHz and 350 MHz. The T3DSO2000HD Oscilloscopes use 12-bit high resolution ADCs and a low noise front end which provides an impressive noise performance to cover a wide range of measurement applications. Each model offers a maximum sample rate of 2 GSa/s (interleaved) and a maximum memory depth of 200 Mpts in interleave mode. The MS configured models also include a 16 channel logic probe as standard.
-
Product
Load Tests
-
For the production and quality assurance of electric motors and electric drive systems, the use of flexible and customer-specific testing technology is required. Vogelsang & Benning supplies the same to the needs and the application of the customer.
-
Product
48V / 300 Amp Load
BD18-48P
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 48V and 50V, (24 or 25 cells at 2V each), battery systems and is extremely cost effective.
-
Product
Saluki SEL7 Series Programmable DC Electronic Load (up to 6kW)
-
The new SEL7 series programmable DC electronic load is a new generation product designed by Saluki Technology. Incorporating high-performance chips, the SEL7 series delivers high speed and high accuracy with a resolution of 0.1mV and 0.01mA (basic accuracy is 0.03% and basic current rise speed is 2.5 A/μs).SEL7 series have wide application from production lines for cell phone chargers, cell phone batteries, electronic vehicle batteries, switching power supplies, linear power supplies, and LED drivers, to research institute, automotive electronic, aeronautic and astronautic, maritime, solar cell and fuel cell etc. test and measurement applications.
-
Product
Load Modules
-
Load Modules are available with a selection of voltage and current ranges. Use for discharge testing batteries, power supplies or test gear.
-
Product
Electronic Load Board 3U CPCI-S (air cooled)
056-377
-
The 3U load boards are designed to simulate the power consumption of a single board computer and other boards on the backplane.
-
-
Product
AC Load Banks
XL1000-XL1250 Series
-
Mosebach Manufacturing Company
The XL1000-XL1250 Series load banks offer you a continuous load at various voltages in a compact, lightweight enclosure.
-
Product
8 Way GPS / GNSS Signal Splitter Passive, 1-2 GHz, N Type, DC Block+200Ω Load 8 Ports
GPS802
-
INSTOCK Wireless Components, Inc
GPS L1 - L5, GLONASS, Galileo splitterLow Insertion Loss (0.6 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)15 VDC & 75 mA max on DC block portsTri Alloy N Type Female (Jack) 50 Ohm
-
Product
Small Compressive Load Cell
CCSM-3.0
-
DLM’s range of Small Compressive load cells can be used independently or in combination as part of weighing platforms.
-
Product
Auto Calibration for Load & Extensiometer
-
Jinan Testing Equipment IE Corporation
TE electronic calibration module provides an easy way to calibrate load cell or extensometer and signal conditioning electronics without using a mechanical calibrator. It enables performing on-site electrical calibration and easy to periodically “spot check”, which will help ensure that the load cell and the extensometer and electronics are calibrated correctly.
-
Product
Oscilloscope, 200 MHz, 2 GS/s interleaved, 4 CH, 200 Mpts/Ch DSO, Fully Loaded with 10.1" Color Display
T3DSO2204HD
Oscilloscope
The T3DSO2000HD series of Bench Oscilloscopes feature 4-channel models with analog bandwidth options of 100 MHz, 200MHz and 350 MHz. The T3DSO2000HD Oscilloscopes use 12-bit high resolution ADCs and a low noise front end which provides an impressive noise performance to cover a wide range of measurement applications. Each model offers a maximum sample rate of 2 GSa/s (interleaved) and a maximum memory depth of 200 Mpts in interleave mode. The MS configured models also include a 16 channel logic probe as standard.
-
Product
Thermocouple, Insert, Receiver, SIM, 8 Pos, 3 Slot (not loaded)
510180111
SIM Insert
Thermocouple, Insert, Receiver, SIM, 8 Pos, 3 Slot (not loaded)Compatible with 310130113 Receiver, i2 MX, 22 Slot VTAC/SIM Insert, EMINot loaded. Thermocouple patchcords need to be purchased separately.
-
-
Product
Miniature S-Beam Load Cell
500 Series
-
The Miniature S-Beam Load Cell is a bi-directional Aluminium strain gage based transducer with high performance and builtin temperature compensation. This design provides better than ±0.1% (full scale) non-linearity and includes overload protection in both tension and compression directions. Options include IEEE1451.4 TEDS capability.
-
Product
Electronic DC Load, 500V, 16A, 400W
LDH400 Series
-
Versatile solution for direct testing of dc power sources and PFCsConstant current, resistance, conductance and power modesWide voltage and current range, 10 to 500V and 0 to 16A400 watts continuous dissipation at 28°C (360W at 40°C)High resolution and accuracy for level settingBuilt-in transient generator with variable slewCurrent monitor output for waveform viewingVariable drop-out voltage for battery testingHigh resolution backlit graphic LCD with soft key controlAnalogue remote control of levels and TTL control of on/off and transient switchingFront and rear input terminalsLoad inputs rated to CAT II (300V)Full bus control via USB, RS232 and LXI compliant LAN interfacesGPIB Option
-
