Waveform Digitizers
take analog waveform's and digitize them.
-
Product
MS/s Waveform Digitize
ATS9416
-
ATS9416 is a 16-channel, 14 bit, 100 MS/s waveform digitizer based on the 8-lane PCI Express Gen2 bus. Boasting data throughput as fast as 3.5 GB/s, ATS9416 is an ideal solution for any application that requires high channel count.
-
Product
16 Mbit/s, 16-Channel Digital I/O Adapter Module for FlexRIO
NI-6584 / 781290-02
Digital I/O Adapter
16 Mbit/s, 16-Channel Digital I/O Adapter Module for FlexRIO—The NI-6584 is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO, creates a digital instrument for interfacing with 16 RX and TX pairs of RS485 or RS422. This digital I/O adapter module for FlexRIO can be used to do real-time interfacing and analysis of RS485 and RS422 as well as other electrically compatible interfaces. The NI-6584 can sample digital waveforms at up to 100 MHz clock rates, has terminated and unterminated options, and full and half duplex configurations.
-
Product
PCIe 16 Bit Arbitrary Waveform Generator - up to 40 MS/s on 2 Channels
M2P.6531-X4
Arbitrary Waveform Generator
The M2p.65xx series offers different versions of arbitrary waveform generators for PCI Express with a maximum output rate of 125 MS/s. These boards allow to generate freely definable waveforms on several channels synchronously. With one of the synchronization options the setup of synchronous multi channel systems is possible as well as the combination of arbitrary waveform generator with digitizers of the M2p product family. The 512 MSample on-board memory can be used as arbitrary waveform storage or as a FIFO buffer continuously stream data via the PCIe interface. Importantly, the high-resolution 16-bit DACs deliver four times the resolution than AWGs using older 14-bit technology.
-
Product
64 Channel 16 bit 125 MS/s Digitizer
VX2745
-
The VX2745 Digitizer is a 64-channel digital signal processor for radiation detectors in a VME64X form factor. It offers not only waveform digitization and recording but also Multi-Channel Analysis for nuclear spectroscopy using Silicon strip, segmented HPGe, Scintillation detector with PMTs, Wire Chambers, and others.
-
Product
PC-based Logic Analysers
-
A logic analyser helps debug and validate digital electronic circuits. It is a tool that allows numerous digital waveforms to be acquired and viewed simultaneously. An oscilloscope can only capture two or four signals at once, the logic analysers we sell capture up to 8, 16 or 32 signals at the same time. A logic analyser processes data across buses, something a scope can't do.
-
Product
PCIe 16 Bit Arbitrary Waveform Generator - up to 125 MS/s on 4 Channels, up to 80 MS/s on 8 Channels
M2p.6568-x4
Arbitrary Waveform Generator
The M2p.65xx series offers different versions of arbitrary waveform generators for PCI Express with a maximum output rate of 125 MS/s. These boards allow to generate freely definable waveforms on several channels synchronously. With one of the synchronization options the setup of synchronous multi channel systems is possible as well as the combination of arbitrary waveform generator with digitizers of the M2p product family.
-
Product
14-bit, 125 MS/s Waveform Digitizer
ATS9146
-
ATS9146 is a 2-channel, 14-bit, 125 MS/s waveform digitizer capable of storing up to 128 Million samples per channel of acquired data in its on-board memory or streaming acquired data to motherboard memory. ATS9146 is a single-lane PCI Express (PCIe x1) Gen 1 card, which supports up to 200 MB/s bus throughput. ATS9146 is an ideal solution for many applications.
-
Product
PCIe 16 Bit Arbitrary Waveform Generator - up to 125 MS/s on 4 Channels, High Voltage Outputs
M2P.6576-X4
Arbitrary Waveform Generator
The M2p.65xx series offers different versions of arbitrary waveform generators for PCI Express with a maximum output rate of 125 MS/s. These boards allow to generate freely definable waveforms on several channels synchronously. With one of the synchronization options the setup of synchronous multi channel systems is possible as well as the combination of arbitrary waveform generator with digitizers of the M2p product family. The 512 MSample on-board memory can be used as arbitrary waveform storage or as a FIFO buffer continuously stream data via the PCIe interface. Importantly, the high-resolution 16-bit DACs deliver four times the resolution than AWGs using older 14-bit technology.
-
Product
150 Watt Electronic Load Module
N3302A
Load Module
The Keysight N3302A is a 150 W (0-30A, 0-60V) electronic load module for use in either the N3300A or N3301A electronic load mainframe in system applications. The N3302A load module is fast and accurate, for programming in constant current, constant voltage, or constant resistance modes, or for making voltage, current or power measurements. The N3302A can also digitize waveforms.
-
Product
20 Bit / 2 MS/s Waveform Digitizer
WFD20
Waveform Digitizer
The WFD20 is a 20 bit Waveform Digitizer for medium-speed / high resolution waveform capturing and analyzing. The module combines an excellent dynamic performance with a very high DC accuracy. The module features a fully differential input path to reduce common-mode level disturbances.
-
Product
PCIe 16 Bit Arbitrary Waveform Generator - up to 40 MS/s on 1 Channel
M2P.6530-X4
Arbitrary Waveform Generator
The M2p.65xx series offers different versions of arbitrary waveform generators for PCI Express with a maximum output rate of 125 MS/s. These boards allow to generate freely definable waveforms on several channels synchronously. With one of the synchronization options the setup of synchronous multi channel systems is possible as well as the combination of arbitrary waveform generator with digitizers of the M2p product family. The 512 MSample on-board memory can be used as arbitrary waveform storage or as a FIFO buffer continuously stream data via the PCIe interface. Importantly, the high-resolution 16-bit DACs deliver four times the resolution than AWGs using older 14-bit technology.
-
Product
Real Time DSP Software
ATS-GPU
-
ATS-GPU is a software framework developed by AlazarTech to allow users to do real-time signal processing using an Open CL compatible Graphical Processing Unit (GPU). Input to the GPU can either come from an AlazarTech PCI Express waveform digitizer or from user-supplied data. Fundamentally, ATS-GPU solves the problem of transferring data from a waveform digitizer to a GPU at very high speeds. A floating point FFT routine built into ATS-GPU has been benchmarked at 235,000 FFTs per second for 2048 points on one input. Ideal for Optical Coherence Tomography (SS-OCT). Benchmarks also showed that users can keep up with 500 MS/s sampling on one channel for 2048 point streaming FFTs.
-
Product
PXIe-6548, 200 MHz, 32-Channel PXI Digital Waveform Instrument
781012-02
Digital Waveform
PXIe, 200 MHz, 32-Channel PXI Digital Waveform Instrument—The PXIe‑6548 is a digital waveform generator and analyzer for interfacing and basic characterization test with 32 single-ended digital pins. The device is capable of sampling digital waveforms at up to 200 MHz and interfacing with user-programmable voltage levels that have a 100 mV resolution. The PXI‑6548 also features advanced synchronization capabilities for building integrated mixed-signal test systems, hardware comparison for bit-error test, and per-bank digital timing features.
-
Product
64 Channel 12 bit 62.5 MS/s Digitizer
V1740
-
The V1740 is a 1-unit wide VME 6U module housing a 64 Channel 12 bit 62.5 MS/s (65 MS/s using external clock) Flash ADC Waveform Digitizer and featuring 2 Vpp single ended input dynamics on two ERNI SMC connectors.
-
Product
PCI Express Waveform Digitizer
ATS9625
-
ATS9625 is a 250 MS/s 16 bit PCI Express waveform digitizer with an on-board, user-programmable FPGA. With fixed ac-coupled input range of 2.5 Vp-p and signal to noise ratio in excess of 75 dB, ATS9625 is an ideal solution for radio applications.
-
Product
NI-6581, 100 MHz, 54 Single-Ended-Channel Digital I/O Adapter Module
780565-01
Digital I/O Adapter
100 MHz, 54 Single-Ended-Channel Digital I/O Adapter Module for FlexRIO—The NI-6581 is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO, creates a digital instrument for interfacing with 54 single-ended digital pins. You can use the NI-6581 to do real-time interfacing of standard protocols and implement customized protocols. The NI-6581 can operate sample digital waveforms at up to 100 MHz. It includes support for common transistor-to-transistor logic (TTL) voltage levels, or other voltage references can be sourced externally using a front panel connector.
-
Product
Digitizer
761 Family
-
The 761 is the family of CAEN Waveform Digitizer with the highest sampling rate Flash ADC (10 bit @ 4GS/s). It can record fast signals from fast organic, inorganic and liquid scintillators coupled to PMTs or Silicon Photomultipliers, Diamond detectors and others, and save them with high efficiency and precision for advanced timing analysis. The acquisition can be externally vetoed/gated. Multiple boards can be synchronized to build up complex systems.
-
Product
PCIe 16 Bit Arbitrary Waveform Generator - up to 40 MS/s on 1 Channel
M2P.6540-X4
Arbitrary Waveform Generator
The M2p.65xx series offers different versions of arbitrary waveform generators for PCI Express with a maximum output rate of 125 MS/s. These boards allow to generate freely definable waveforms on several channels synchronously. With one of the synchronization options the setup of synchronous multi channel systems is possible as well as the combination of arbitrary waveform generator with digitizers of the M2p product family. The 512 MSample on-board memory can be used as arbitrary waveform storage or as a FIFO buffer continuously stream data via the PCIe interface. Importantly, the high-resolution 16-bit DACs deliver four times the resolution than AWGs using older 14-bit technology.
-
Product
Digitizer
720 Family
-
The 720 is a family of CAEN Waveform Digitizer able to perform basic waveform recording and run online advanced algorithms (DPP) of charge integration and pulse shape discrimination. Data is read by a Flash ADC, 12-bit resolution and 250 MS/s sampling rate, which is well suited for mid-fast signals as the ones coming from liquid or inorganic scintillators coupled to PMTs or Silicon Photomultipliers. In the waveform recording mode, algorithms of zero suppression are also implemented to reduce the data throughput.
-
Product
PCIe 16 Bit Arbitrary Waveform Generator - 40 MS/s on 2 Channels
M2P.6541-X4
Arbitrary Waveform Generator
The M2p.65xx series offers different versions of arbitrary waveform generators for PCI Express with a maximum output rate of 125 MS/s. These boards allow to generate freely definable waveforms on several channels synchronously. With one of the synchronization options the setup of synchronous multi channel systems is possible as well as the combination of arbitrary waveform generator with digitizers of the M2p product family. The 512 MSample on-board memory can be used as arbitrary waveform storage or as a FIFO buffer continuously stream data via the PCIe interface. Importantly, the high-resolution 16-bit DACs deliver four times the resolution than AWGs using older 14-bit technology.
-
Product
Software
ATS-SDK
-
ATS-SDK is a Windows and Linux compatible software development kit created by AlazarTech to allow users to programmatically control and acquire data from its line of waveform digitizers. With full support for C/C++ and C# (Visual Studio or GCC), MATLAB, LabVIEW and Python environments, ATS-SDK is the most powerful, efficient and high-performance programming environment. ATS-SDK includes many example programs that can be used as a starting point for custom code development for specific applications. As of version 7.1, ATS-SDK replaces ATS-VI as the recommended programming environment for LabVIEW users.
-
Product
Software
-
Besides the primary WITE32 Test Environment package at the heart of our spinstand-based test systems, Guzik offers a variety of software options to provide additional measurement accuracy and analysis. Control and Automation software enhances various electro-mechanical capabilities of the test system (such as servo accuracy), and the available suite of Analysis software tools provides deep insight into the drive component under evaluation. Adjacent Track Interference, 3D Pulse Profile, Media Scanning and Bit Error Rate are examples of some of the optional additions. Some software tools require the WDM5000 Waveform Digitizer to be part of the overall test system.
-
Product
PXIe-6545, 200 MHz, 32-Channel PXI Digital Waveform Instrument
780993-02
Digital Waveform
200 MHz, 32-Channel PXI Digital Waveform Instrument—The PXIe‑6545 is a digital waveform generator and analyzer for interfacing with 32 single-ended digital pins. The device is capable of sampling digital waveforms at up to 200 MHz and interfacing with common transistor‑to‑transistor logic (TTL) voltage levels. The PXI‑6545 also features advanced synchronization capabilities for building integrated mixed-signal test systems and per-bank digital timing features.
-
Product
PXI-6541, 50 MHz, 32-Channel PXI Digital Waveform Instrument
778952-02
Digital Waveform
50 MHz, 32-Channel PXI Digital Waveform Instrument—The PXI‑6541 is a digital waveform generator and analyzer for interfacing with 32 single-ended digital pins. The PXI‑6541 can sample digital waveforms at up to 50 MHz and interface with common transistor‑to‑transistor logic (TTL) voltage levels. The PXI‑6541 also features advanced synchronization capabilities for building integrated mixed-signal test systems.
-
Product
PXIe-6545, 200 MHz, 32-Channel PXI Digital Waveform Instrument
780993-03
Digital Waveform
200 MHz, 32-Channel PXI Digital Waveform Instrument—The PXIe‑6545 is a digital waveform generator and analyzer for interfacing with 32 single-ended digital pins. The device is capable of sampling digital waveforms at up to 200 MHz and interfacing with common transistor‑to‑transistor logic (TTL) voltage levels. The PXI‑6545 also features advanced synchronization capabilities for building integrated mixed-signal test systems and per-bank digital timing features.
-
Product
Digital Instruments
-
Digital Instruments generate and acquire high-speed digital waveforms for transmitting data, communicating with devices under test, or testing digital interfaces. These instruments are ideal for semiconductor characterization and production, interfacing to LVDS and TTL digital electronics, and testing the functionality of high-speed serial links.
-
Product
High-Speed Digitizers
ADP7000 Series
-
Guzik AXIe ADP7000 Series High-Performance Digitizer and Digital Processor combine high-speed waveform digitizer with built-in digital signal processing, which both enable mixed-domain signal capture and analysis with high-speed data transfer links to computers. The ADP7000 Modules (ADP7084 and ADP7104) come in a display-less 2U high 19” AXIe modular form factor.
-
Product
MS/s Waveform Digitizer
ATS9440
-
ATS9440 is a 4-channel, 14 bit, 125 MS/s waveform digitizer based on the 8-lane PCI Express interface. Boasting data throughput as fast as 1.6 GB/s, ATS9440 is an ideal solution for many applications, including spectrometry, radar, ultrasonics and RF signal recording.
-
Product
NI-6581B, 100 MHz, 54 Single-Ended-Channel, Kintex-7 FPGA-Support, Digital I/O Adapter Module for FlexRIO
783887-01
Digital I/O Adapter
100 MHz, 54 Single-Ended-Channel, Kintex-7 FPGA-Support, Digital I/O Adapter Module for FlexRIO—The NI-6581B is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO, creates a digital instrument for interfacing with 54 single-ended digital pins. A digital I/O adapter module for FlexRIO can be used to do real-time interfacing of standard protocols and implement customized protocols. The NI-6581B can operate sample digital waveforms at up to 100 MHz. It includes support for common transistor-to-transistor logic (TTL) voltage levels, or other voltage references can be sourced externally using a front panel connector.
-
Product
Waveform Digitizer
ATS9462
-
ATS9462 was the world''s first waveform digitizer with a 4-lane PCI Express interface. Boasting data throughput as fast as 720 MB/s and sample rate of 180 MS/s across 2 simultaneous inputs, ATS9462 is an ideal solution for many applications, including OCT, RF signal capture, ultrasonic inspection and radar.
