-
Product
Waveguides
-
CAES offers a full range of rectangular (WR-22 to WR430) and double-ridge (WRD-180 to WR430) waveguides covering frequency bands from a few hundred MHz to 100 GHz.
-
Product
Millimeter Wave Continuously Variable Waveguide Attenuators
-
Our millimeter wave variable waveguide attenuators allow designers and engineers to test their systems at various signal strengths and attenuation values to determine the optimum signal performance of the system. The key feature of these waveguide attenuators is that the attenuation level is adjusted using a built-in micrometer which enables repeatable and rapid re-setting to different attenuation levels without the need for additional external components. Our waveguide attenuators handle varying attenuation levels from 0 to 30 dB over the specified band allowing the designer to tune the attenuation level needed for the application. These continuously variable waveguide attenuators cover a broad frequency range of 33 to 110 GHz in five bands and also display flat performance across a wide band with low insertion loss.
-
Product
Millimeter Wave Converter
ZVA-Z Series
-
Millimeter-wave measurements in the V, E, W, F, D, G, J and Y band – network analysis in frequency ranges from 50 GHz to 500 GHz depending on the converter model. Featuring a wide dynamic range, the RPG converters offer high operating convenience and allow fast measurements. Two-port measurements can be performed using a four-port network analyzer and two converters; no external generator is required. When using a two-port network analyzer, an external generator is needed to supply the LO signals.
-
Product
Millimeter Wave Converters
ZC-Series
-
*variable output power*wide dynamic range*wide frequency range*highly stable measurement*convenient handling
-
Product
Waveguide Cassette
-
Waveguide cassettes provide easy way for the network analyzer calibration and material properties as dielectric permittivity or (and) magnetic permeability measurements. By changing insertion sections, it is possible to calibrate "Short" and "Thru". Optional cassettes with quarter wave "short" inserters are available. Using this waveguide cassette, it is possible to do vector network analyzer calibration or additional scalar network analyzer calibration. Insertable sample holders supports two measurement methods: the rod in the centre of the waveguide and filled waveguide cross-section.
-
Product
Custom Waveguides
-
Custome waveguides for commercial, industrial, government and research & development industries. Consult with our engineering staff on your millimeter wave needs. View more Custom Waveguides
-
-
Product
Waveguide Duplexer
-
Waveguide Duplexers supporting commercial communication to combine transmit and receive on to one antenna
-
Product
Waveguide Calibration Kits
-
Designed to provide accurate calibration of vector network analyzers (VNAs) that are used for measurements in standard rectangular waveguide from 2.6 to 50 GHz (WR284–WR22).
-
Product
E Bend Waveguide
-
E-plane waveguide bends are sections of high-precision crafted waveguides and shaped to either 30º, 45º ,60º, or 90º angles for e-plane needs. It directs the radio frequency beam and “bends” the signal to go the direction you want. Think of it like Tokyo drifting around a corner in your car. Precision MMW will help you with the highest quality E bend waveguides. We are a millimeter wave spectrum manufacturer of various active and passive mmWave products and sub-system engineering.View more E Bend Waveguide
-
Product
Waveguide To Coax Adaptors
-
The transitions from waveguide to coaxial line (SMA connector type) are offered up to 110 GHz.
-
Product
Waveguide Probes
-
We are a leading Manufacturer & Exporter of Waveguide Probes such as Tunable Probe and Waveguide Matched from India.
-
Product
Waveguide Bends
-
Fairview Microwave’s lines of precision waveguide bends are widely used in applications such as high efficiency RF, microwave and mm-wave transmissions, satellite and military communications, radar, telecom, instrumentation and test benches. In waveguide systems that require a signal to turn or bend 90 degrees, Fairview’s waveguide bends are used to facilitate that bend or turn without degrading the transmission signal. These WG bends operate from 5.85 GHz to 90 GHz across 12 frequency bands and are available in sizes from WR-12 to WR-137. This family of waveguide bends also boast low loss and VSWR as low as 1.08:1 and are available in both E-plane and H-plane configurations. They are constructed using gold plated, oxygen free hard copper (OFHC) or painted copper alloy depending on the model and are also offered with either a UG-style flange per the military standard or a CPR-style flange. Many models are RoHS compliant.
-
Product
Double Ridged Waveguide Horn
DRH30
-
Frequency range: 2.5GHz - 30 GHz VSWR (max): < 1.55:1Impedance: 50 O (Ohm)Connector: K female Power (CW / Peak): 25W / 50 W
-
-
Product
Double Ridged Waveguide Horn
QRH18
-
Frequency range: 1 GHz - 18 GHz VSWR (max): < 2.5:1Impedance: 50 O (Ohm)Connector: 2xSMA female Power (CW / Peak): 100W / 170 W
-
Product
Double Ridged Waveguide Horn
H-A50
-
Frequency range: 33 GHz - 50 GHz VSWR (max): < 1.35 :1Impedance: 50 O (Ohm)Connector: 2.4 female Power (CW / Peak): 10 W / 20 W
-
-
Product
Double Ridged Waveguide Horn
QRH400
-
Frequency range: 400 MHz - 6 GHz VSWR (max): < 2.3 :1Impedance: 50 O (Ohm)Connector: 2xN female Power (CW / Peak): 350 W / 350 W
-
-
Product
WR-8 Waveguide Straight
WAG-08-SXX
-
Precision mmw F-Band, WR-08, Straight waveguides are built with high precision and then gold plated for high corrosion resistance. They have very low loss and great VSWR. Manufactured to rigid specifications, these transmission line components provide minimum detrimental effects on the overall system VSWR.XX = length in inchesFeatures of WR-08, Waveguide Straights• 90 GHz to 140 GHz• Low Insertion Loss, typical for length• Low Return Loss, typical for length• UG-387 flangeView more WR-8 Waveguide Straight
-
Product
WR-12 Waveguide Straight
WAG-12-SXX
-
• 60 GHz to 90 GHz• Low Insertion Loss, typical for length• Low Return Loss, typical for length• UG-387 flangeView more WR-12 Waveguide Straight
-
Product
Waveguide Receiver Protector
-
The continuous evolution of radar systems creates an ever more complex RF power environment in which sensitive receivers must operate and survive. Teledyne limiters deliver vital protection for a wide range of receivers, providing protection from L-Band through to Ka-Band (1 - 40GHz) and peak power levels up to 1MW with unparalleled low insertion loss levels.
-
Product
Waveguide Tunable Attenuators
-
*Low Insetion Loss*Full Waveguide Band Coverage*Precise Adjustment*High Maximum Attenuation
-
Product
Waveguide Antennas
-
Waveguide horn antenna is also known as a WR-15 horn antenna. This WR-15 waveguide horn antenna has a dB nominal gain and a ug-385/u flange. Our dB WR-15 horn antenna has a minimum frequency of 50 GHz and a maximum frequency of 75 GHz.
-
Product
Waveguide Power Sensor
V8486A
Power Sensor
The V8486A waveguide power sensor measures average power over the frequency range 50 GHz to 75 GHz and power range -30 to +20 dBm.
-
-
Product
K-Band Waveguide Gunn Oscillator Module
FMWGN1001
-
FMWGN1001 is a K Band Waveguide Gunn Oscillator with a Center Frequency of 24.125 GHz and a Tuning Range of +/- 1.0 GHz. The unit has a Phase Noise @ 100kHz Offset of -95 dBc/Hz typ and Frequency Stability of -0.4 MHz/°C max. The Gun Oscillator has an Output Power of 10 dBm min and Power Stability of -0.04 dB/°C max. The Waveguide Gun Oscillator uses a Bias Voltage of 5.0 Volts and a Bias Current of 200 mA and has a Waveguide Size of WR-42 with a UG-595/U Flange.
-
-
Product
Manual Attenuator (Waveguide)
-
Manual control waveguide attenuators in both variable (continuous) or stepped in a variety of frequencies, attenuation values / step sizes and power levels
