Filter Results By:
Products
Applications
Manufacturers
Wire Cable Test
The verification of wire cable integrity.
-
product
Lan Cable Tester
Shanghai Beha Electronics Co., Ltd.
Designed for RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable etc.• The Lan cable tester can verify cable continuity, open,short circuit and miss-wired.• The remote receiving unit is available for installed cables far away either on the wall plates or on the patch panels.• Auto and manual scan function.• Ground wire test.• Lock status function.• Buzzer sound warning for wire status.• Display: LED indication for wire status.
-
product
Cable + Network Tester
LinkIQ
The LinkIQ™ Network+Cable Tester is designed to provide trusted cable testing along with network testing professionals need to do their jobs. LinkIQ™ validates cable performance (up to 10 Gig) using frequency-based measurements and provides distance to fault information along with a wire map of the cable under test.
-
product
Universal LightProbe Sensor Six-Pack
S6P
The Universal LightProbe Sensor Six-Pack provides a compact and efficient way to install six Universal LightProbe Sensors in a single space-saving unit. The convenient installation provides two standard circuit board header connectors, enabling the use of standard ribbon cable connections for the Universal LightProbe Sensors’ output. A single power and a single ground wire is all that is needed to connect as many as six Sensors. The Sensor Six-Pack will accommodate any combination of the pre-programmed Universal LightProbe Sensor models, which can then be paired with a wide variety of Fiber-optic Probes to customize for a specific test. For example, the Penta Sensor can be combined with “Trident” Fiber-optic Probes to test 18 LEDs.
-
product
LAN Network Testers
A cable detector can locate open power cables, either live or without current, up to 300 V. A cable detector can locate cables, circuits, short circuits and ground wires. To perform these functions, it is not always necessary to disconnect electrically sensitive devices or to disconnect the power to the cable being tested.Many cable detector devices can also locate ferrous and non-ferrous metals, wood and plastic with high degrees of accuracy. A cable detector provides a safe way to test wall sockets for which no electrical plans or wiring information is available about the cables or their output. A cable detector is very versatile, as it ensures speed and safety when making holes in walls, ceilings and floors.
-
product
SCSI CABLE TESTER
ST123
Continuity tests alone are not sufficient to qualify SCSI cable assemblies. Proper testing of SCSI cables must include a test for correct connection of twisted pairs and shielding. Continuity tests check only that wires are making connections on both ends of a cable.Twisted pairs in the cable must be matched with the correct SCSI signal pairs - otherwise, it is possible to have a SCSI signal (signal and ground pair) placed on wires that are not in the same physical twisted pair (see diagram at right). This will cause crosstalk with resultant SCSI errors.
-
product
Lan Cable Tester
185 LCT
Standard Electric Works Co., Ltd
● Designed for RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable.● The LAN cable tester can verify cable continuity, open, short circuit and miss-wired.● The remote receiving unit is available for installed cables far away either on the wall plates or on the patch panels.● Auto and manual scan functions.● Ground wire test. ● Lock status function.● Buzzer sound warning for wire status.● Display : LED indication for wire status.
-
product
Push Pull Force Gauges
Used in rubber plastic, textiles, waterproof materials, wire and cable, metal materials tensile, compression, bending, cutting and mechanical propertie test, increase the affix to do bending test, it is scientific research institues, universities and colleges,industrial and mining enterprises, the technical supervision and inspeciton arbitration of the department idea test equipment.
-
product
5 A portable digital micro-ohmmeter
MPK-254
The MPK-254 digital very low resistance ohmmeter is a portable, microprocessor-controlled instrument used to accurately measure resistances of switches and circuit breaker contacts, transformer and motor windings, wire and cable samples, joints in busbars, etc., using test currents from 1 mA up to 5 A.
-
product
10A DIGITAL MICRO-OHMMETER
MPK-2000e
The MPK-2000e digital very low resistance ohmmeter is a portable, microprocessor controlled instrument used to accurately measure resistances of switches and circuit breaker contacts, transformer and motor windings, wire and cable samples, joints in busbars, etc., using test currents from 1mA up to 10A. It uses the Kelvin-type, four-terminals measurement principle, thus eliminating errors caused by lead and contact resistances.
-
product
Material Test Machines
Sanwood Environmental Chambers Co ., Ltd.
Sanwood Universal Test Machines, UTM, are widely use for different material testing, like semi-product & finished product made of rubber, plastic, metal, nylon, non-woven fabrics, textile, tape, polyfoam, waterproof materials, wire, cable, etc. With different test jigs or fixtures, the UTM can run the tensile, compression, shearing foce, adhesion, peeling force, tear strength, fatigue, etc test according to GB, CNS, ASTM, ISO, DIN, JIS, EN test standards.
-
product
BNC (F) To Alligator Test Clips
2630
BNC (f) to alligator test clips. Converts BNC (male) cables / connectors to alligator test clips for test versatility. BNC connector is molded directly to the wire for pull strength durability and dust and moisture resistance.
-
product
Laboratory Ozone Test Chamber
CX-150
Shenzhen Chuangxin Instruments Co., Ltd.
Laboratory Ozone Test chamber is widely used to control products quality in measuring quality control; Rubber & Plastics; automobile production; wire and cable; packing materials; instruments and meters; medical equipment; civilian nuclear energy; civil aviation; colleges and universities; research laboratories; inspection arbitration, and technical supervision departments and other rubber products.
-
product
LCD Multifunction Cable Tester
MT-7059
Display test result on large LCD for easy reading and cable status identificationThe wire can be tracked directly in connection with Ethernet service, router, and PC terminalValidate and troubleshoot wiring on RJ11/RJ45 cables, Coaxial cable, USB cable, IEEE 1394 cableTest cable status for continuity, shorts, opens,miswired, crossover9 different tones selection for convenience use under different environment conditionAll installation and maintenance fields of telecommunication, networking, cable TV and more
-
product
BNC (F) To Minigator Test Clips
2631
BNC (f) to minigator test clips. Converts BNC (male) cables / connectors to minigator test clips for test versatility. BNC connector is molded directly to the wire for pull strength durability and dust and moisture resistance.
-
product
Flammability Test Chamber
Shenzhen Bonad Instrument Co., Ltd.
BONAD’s flammability test chamber complies with IEC 60950, IEC 60695, IEC 60112, IEC 60332 and other standards. We not only provide standard wire and cable combustion test equipment and leakage tracking test equipment and other electrical test equipment as well as a variety of different combustion test equipment, but we also provide customization and can develop professional and high-quality test equipment according to test requirements. For more information, please contact us, BONAD will provide you with professional technical advice and high-quality testing equipment.
-
product
Clamp Multimeters
Clamp meters test AC/DC voltage, DC voltage, resistance and continuity. Measure conductors at any point in the wire or cable.
-
product
Home Tool
PA-46
Residential Network cabling is becoming more prevalent. Installers need new and better tools to test and verify higher bandwidth cabling and complex home networks for high-bandwidth internet service, security systems, digital video, and smart appliances. The HomeTool is designed to prevent and solve cable and wire installation problems in such network.
-
product
Multi-purpose Cable Tester and Cable Tracer
165 CB
Standard Electric Works Co., Ltd
● 165 CB is an ideal tool which can test the correct pin configuration for different kinds of cables.● For testing: -RJ45/RJ11 -USB -COAX -BNC cable -Multi-wire cable● Auto-scan and manual-check function● Buzzer sound warning for wire status● 2 LED module indicators on the master unit which can do both of transmitter and receiver functions for RJ45/RJ11 cable testing. Users don't need to use the receiving unit.● 165 CB provides a variety for checking cable continuity, open status, short status and miss-wired. ● Ground (shielded ) wire test.● LED indication for wire status.● Power source : 9V battery
-
product
Robustness of Terminations Tester
King Design Industrial Co., Ltd.
*Cable test length is 450mm.*Pull the leading wire by 4.08kg in 170 o of angle.*X-axle: from 170o right swinging to 170o left.*Y-axle: from 170o up swinging to 170o down.*Z-axle: pull at 170 o and spin.
-
product
PC-NET Cable Tester
PR-09
The PC-NET Cable Tester is a portable, stand-alone unit that provides an affordable way to quickly test PC, Network, Telco, Coax, USB and IEEE1394 cables for continuity and wiring configuration for any combination. Open, shorts, miswires and cross-connected wires are detected immediately. The interchangeable connectors boards offers flexibility and convenience easy to read LED instantly indicates good or faulty. The tester is suitable for use by computer dealers and computer hardware outlets.
-
product
High Voltage, Continuity & Hipot, Cable & Wire Harness Test Systems
CableEye HVX, HVX-21
Fast ● Simple ● Precise
Advanced wiring analyzer scans for continuity (opens, shorts), miswires, resistance, capacitance, components (resistors, diodes, LEDs, capacitors) dielectric breakdown, insulation resistance, intermittent connections
HVX (Item 829) 1500 Vdc, 1000 Vac
HVX-21 (Item 829A) 2100 Vdc, 1200 Vac
For diagnostic and Pass/Fail Testing — Permits expanded testing (compared to models in our low voltage product line) for insulation resistance (IRI) and dielectric breakdown (DWV).
All CableEye testers are suitable for production, fault diagnosis, QC (Quality Control), assembly, and prototyping of standard or custom cables. Each combines test, fault location, design, documentation, labeling, and database storage in one instrument. Tests can be performed on long cables (with or without connectors) or no cables (e.g. connectors, backplanes, PCBs, components).
Standard Features & Benefits:- USB certified, PC-based tester for a versatile, fast, robust system with long life-cycle.
- Multilingual, dynamic, graphic-rich display (netlist & wiring schematic) provides clarity and speeds diagnostics.
- 128 Test Points, expandable to 1024 providing flexibility as your product line changes.
- User-selectable voltage to each connection group in the cable simplifies an otherwise complex process, accelerating testing.
- Programmable Ramp Up, Ramp Down, Dwell Time (same as Test Time), Trip Current, and Trip Delay (same as Soak Time) adds versatility.
- Current leakage detected during HV test phase provides a measure of insulation resistance up to 1 GΩ (HVX) and 5 GΩ (HVX-21) - any leakage current exceeding a preset limit reveals the presence of moisture, flux, or other contamination on exposed contacts.
- Real-time screening for intermittent connections for pinpointing elusive faults and improving quality.
- Automation scripting in a simple, intuitive language allowing non-programmers to reduce operator error by automating repetitive steps.
- Pop-Up Work Instructions. choose the exact amount of detail, imagery, language and automation you need to ensure your work instructions and tests are carried out flawlessly.
- Flexible tolerancing: optionally define as percentages or absolute terms, as well as asymmetrically (e.g. +0%/-10%) for improved yields.
- Barcode-tracking & archival data-logging to achieve error-proof test process and improved traceability & productivity.
- Print PASS/FAIL labels, test reports (with or without color wiring schematics/netlists) and log reports to satisfy ISO9000 reporting requirements.
- Compatible with laptop and touchscreen PCs for fieldwork and rack/off-bench mounting.
Includes:
CB29 board set (Item 759) for bare wire connections; comprehensive PC software with Database of >200 standard cables; 2 yr Product Support Subscription comprising Warranty, free tech support, and free software upgrades.
Select Add-On Options:
Hardware: 128-point Expansion Modules (attach to base); 4-Wire Kelvin Resistance Measurement, 1 mΩ at 1 A; Advanced Measurements; External Measurement Instrument Port (e.g. 10 GΩ Isolation at 100 V); Remote Control Connector for Deadman Switch; Environmental Sensor
Software: PinMap™ fixture editor, Connector Designer™ connector editor, or Autobuild™ guided assembly modules
camiresearch.com |@CAMI_CableEye |+1.978.266.2655 -
product
Pulse generator
9355-1
Solar Model 9355-1 Pulse Generator is designed to provide impulse excitation by means of an injection probe placed around interconnecting cables or power wires. The unit uses a charged transmission line (50 ohms) to generate a pulse with less than 2 nanoseconds rise and fall time, and duration of approximately 30 nS, calibrated in a 50 ohm fixture to deliver up to 5 amperes at a rate of 30 p.p.s. for one minute as required by MIL-STD-461D/E, test method CS115.
-
product
Cable Continuity Test Fixture
CCT
6 and 8 Wire Cable Continuity Test Fixtures For convienient desk top and bench top The most important features of this cable continuity tester is its ease of use intuitive control functions and durability in a production environment.
-
product
Cable Detectors
PeakTech Prüf- und Messtechnik GmbH
This cable detector works acoustically and offers a quick and inexpensive solution to find voltage-free lines in the house installation, to test telephone lines, to identify individual cables / wires or to carry out a continuity test.
-
product
NEXTest 7
PK-2030/2032/2033/2036/2037/2038
NEXTest 7 is an advanced and unique tester in the market. It's designed to check and troubleshoot the pin connections of Display port & HDMI prior to installation on equipment. By using advanced technology to verify the integrity (20 pins + shield) of both display port and HDMI cables, especially for HDTV installation and DIY termination in the field, solving your cable testing need, unlink all of the other testers verify 9 circuits only. It checks for opens, shorts, miswires and intermittent faults in all conductors plus shield continuity, most tester only test for opens. It displays cable map results of both TX (near end) and RX (far end) on the main unit, either on testing before or after installation cables. User can easily read and determine the actual 21 pins configuration on main unit. It employs both auto and manual scanning of 21 wires. Tone Generator mode transmits two selectable tones on each pin for use with Net Probe (PR-06P) optional, enables one to quickly locate a cable. It's capable of testing up to 8 cables and locations at one time. NEXTest 7 especially features a self-learning mode to memorize cable pin out for testing large quantity standard or custom cables for PASS/FAIL a snap, makes testing quick and more efficient.
-
product
Cable/Harness Tester
CR
As a wire harness tester, a cable tester, a continuity tester, a component tester, and a guided harness-assembly aid, the Easy-wire CR tester is versatile. The easy-wire CR features Windows based software that allows you to create custom graphics of your connectors and light LEDs to guide the harness assembly process. Test Points: 256-32,000, Test Current: 6.5 mA max
-
product
LCZ LCR Meter
SS1063
This (SS1061 / SS1062 / SS1063) LCZ Meters are a test system for passive components designed for the use in electronic inspection or production process for quality control. They meet any demanding requirement on production speed and precision, discrimination of qualified products from unqualified ones, as well as internal setup, storing and calling function for up to 10 instrument groups, so they Like as: transformer, inductor, resistor, capacitor, relay, motor, generator, eletric valve, contactor,cable,wire,etc.
-
product
Cable Length Meter
Shanghai Beha Electronics Co., Ltd.
*Cable length measurement by pulse reflection measurement, only required one cable end (with two wires)*Resistance measurement*Acoustic continuity test
-
product
DSE Wire Testers
DSE Test Solutions your gateway to a world of wire technology.We supply high-quality test equipment for the wire and cable industry. Our extensive range of intelligent test equipment is used for quality control and production optimisation of enamelled wire and cable.
-
product
Low-Temperature Impact Device
DWC-1
This low-temperature impact device is compliance with standard requirement of IEC60245, IEC60227, IEC60540, GB5013-2008, GB5023-2008 and GBT2951-2008. It’s used to test all kinds of PVC sheathed cable, wire, soft wire and no sheath of parallel soft PVC insulated impact resistance at low temperature. Specification: • Working temperature: -15℃±1℃ • Impact height: 10~200mm adjustable • Length of specimen: 5D~150D • Material: 304 stainless steel • Completion time once: 3~5s • Completion number of units for once: ≥2pcs • Weight: 100/200/300/400/500/600/750/1000/1250/1500g • Low temperature box to match additionally
