3U PXI Chassis
See Also: PXI Chassis, 6U PXI Chassis, Portable PXI Chassis
-
Product
PXI 1A Fault Insertion Switch 22-Channel
40-195-001
Relay
The 40-195 is a 22 Channel Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions on pairs of signals between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Relays in-line with the signal paths allow open circuit conditions to be simulated on either side or both sides of a signal pair. Relays between each channel pair enable adjacent signals to be shorted, and relays between signal paths and the "Fault" connection allow the application of external user applied fault conditions.
-
Product
PXI Resistor Module 2-Channel 1.5R to 2.04k
40-293-022
Programmable Resistor Modules
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
3-Channel 200 MHz A/D and 2-Channel 800 MHz D/A with Virtex-7 FPGA - 3U VPX
Model 52720
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Three 200 MHz 16-bit A/Ds- One digital upconverter- Two 800 MHz 16-bit D/As- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- PCI Express (Gen. 1 and 2) interface up to x4- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- 3U VPX form factor provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
3U CompactPCI Mini PCI, Mini PCIe Carrier Board
cPCI-3W10
Carrier Board
- Supports 32bit, 33/66MHz CompactPCI® bus- One SIM card socket- One Mini PCI and one Mini PCIe socket- PICMG® 2.0 R3.0 compliant
-
Product
PXIe8862, 2.6 GHz 8-Core PXI Controller
788817-01
Embedded Controller
The PXIe8862 is an Intel Core i7 8Core embedded controller for PXI Express systems. You use the PXIe8862 for processor-intensive RF, modular instrumentation, and data acquisition applications. The PXIe8862 includes two 10/100/1000/2500BASET (Gigabit) Ethernet ports, two USB 3.0 ports, four USB 2.0 ports, as well as an integrated hard drive, serial port, two Thunderbolt 4 ports, and other peripheral I/O.
-
Product
3U CompactPCI Serial 2-Port CAN From PEAK Module
cPCI-A3CAN
cPCI Card
- Follow PICMG® CompactPCI® Serial design guide- CompactPCI® Serial, 3U 4HP- 2x D-Sub CAN ports in front panel- Operating temperature: -40°C to +85°C- Designed to meet EN50155 standards
-
Product
PXI High Density Multiplexer, 2-Bank, 40-Channel, 1-Pole
40-615A-017
Multiplexer Module
The 40-615A-017 is a 2-bank, 40-channel, 1-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. These feature a wide range of switching configurations and are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector.
-
Product
PXI 14 Slot 6U
-
14 slots 6U Backplane PXI with two CPCI-segments of 7 – 3U-slots each and special rear pallet PXI-bridge mounted on extended front connector pins on the upper 3U-section and the lower 3U-section.
-
Product
PXI General Purpose 2A Relay Module 16xDPST
40-132-102
Relay
Pickering Interfaces 40-131/132 modules are a range of low cost, general purpose electromechanical relay cards. They are capable of switching voltages up to 300VDC/250VAC and current up to 2A. They are suitable for use where reed relay based switching cards do not have sufficient voltage or current carrying capability. Applications include the switching of medium power AC and DC loads, or slave switching larger relays, contactors or solenoids. Connections are made to the card via a front panel mounted 78 pin D-Type connector plug.
-
Product
PXI Embedded Controller
PXI-3982
Controller
The ADLINK PXI-3982 PXI embedded controller, based on the 6th generation Intel® Core™ i7 processor, is specifically designed for hybrid PXI based testing systems, delivering a rugged yet stable platform for a wide variety of testing and measurement applications.
-
Product
75/150-Watt DC/DC Converter w/Holdup, 3U cPCI
75PS4
DC Converter
NAI’s 75PS4 is a DC/DC Converter that plugs directly into a standard 3U cPCI chassis with a 0.8” slot. It is conduction-cooled through the card edge/wedgelock. This programmable, switching power supply accepts a +28 VDC input and is available in either a 75 Watt or 150 Watt-version.
-
Product
PXI Triple SP4T Multiplexer 6GHz 50 SMA
40-784A-103
Multiplexer Module
Pickering Interfaces’ range of 40-784A PXI Microwave Multiplexer Modules have a characteristic impedance of 50Ω and are capable of switching signals up to 40GHz. Available in single, dual or triple, SP6T or SP4T formats, they are suitable for constructing complex microwave switching networks and provide a range of switching configurations to suit most applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors
-
Product
PXIe8862, 2.6 GHz 8-Core PXI Controller
790622-01
Embedded Controller
The PXIe8862 is an Intel Core i7 8Core embedded controller for PXI Express systems. You use the PXIe8862 for processor-intensive RF, modular instrumentation, and data acquisition applications. The PXIe8862 includes two 10/100/1000/2500BASET (Gigabit) Ethernet ports, two USB 3.0 ports, four USB 2.0 ports, as well as an integrated hard drive, serial port, two Thunderbolt 4 ports, and other peripheral I/O.
-
Product
PXI Express High Speed Optical FPGA Board
HSS-8324
-
The Conduant HSS-8324 Optical FPGA board provides the user with a hardware platform that is able to sustain full-duplex high-bandwidth transfers through its 8-lane Gen3 PXI Express (PXIe) interface and its 24-lane optical interface. The PXIe interface provides a theoretical maximum throughput of 8GB/s (simultaneous in and out).
-
Product
PXIe-5663E, 6.6 GHz PXI Vector Signal Analyzer
781259-02
Signal Module
6.6 GHz PXI Vector Signal Analyzer - The PXIe‑5663E offers wide instantaneous bandwidth and supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. You can use a PXIe‑5663E as either a spectrum analyzer or vector signal analyzer, and you can use it with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5663E can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5663E provides a low-cost solution to high-performance RF measurements.The PXIe-5663E comprises the following modules:• PXIe-5601 RF Signal Downconverter• PXIe-5622 IF Digitizer• PXIe-5652 RF Analog Signal GeneratorThere is no physical device named "PXIe-5663E".
-
Product
4-slot LXI Chassis
MezaBOX-4M LXI
-
MezaBOX-4M LXI is a device that ensures the operation of various mezzanine modules (up to 4) installed in it, under the control of a personal computer via USB2.0 or ETHERNET 10/100/1000 Base T (local area network) interfaces of a personal computer ... MezaBOX-4M LXI is intended for use as a mezzanine carrier in multichannel systems for collecting / issuing information, both digital and analog.
-
Product
PXI Express Optical FPGA Board
HSS-8324
FPGA Board
The Conduant HSS-8324 Optical FPGA board provides the user with a hardware platform that is able to sustain full-duplex high-bandwidth transfers through its 8-lane Gen3 PXI Express (PXIe) interface and its 24-lane optical interface. The PXIe interface provides a theoretical maximum throughput of 8GB/s (simultaneous in and out).
-
Product
15" Configurable Panel PC Chassis For Selectable Mini-ITX Motherboard
PPC-6151C
Panel PC
15” true-flat PPC with Resistive touchSupports certified mini-ITX motherboard up to 65W TDP processorSupport PCI or PCIe expansion slotFront LED indicators for power statusFront panel is IP66 compliant
-
Product
PCI Express® Bus To 3U PXI Express™ Chassis Expansion Kit
ACL-EXPRESS-7
-
The PCIe-to-PXIe expansion kit includes one PCIe-8560, one PXIe- 8565, and one ACL-EXPRESS cable (7 meters).
-
Product
PXI FPGA & Measurement Accelerator
Measurement Accelerator
Keysight PXI FPGA & measurement accelerator provide digital-pre-distortion (DPD) and envelope tracking (ET) measurements that are embedded in high performance FPGA processing cards.
-
Product
PXI Single 32x8 Matrix, 1 Pole Screened
40-531-021-S
Matrix Switch Module
Model 40-531 very high density matrix modules are configured as a 32x8, while the 40-532 modules are configured as a Dual 16x8. Both modules are available in a choice of reed relay formats: 1-pole, 2-pole and 1-Pole screened. The screened version is suitable for switching coaxial signals up to 50MHz. Typical applications include signal routing in Functional ATE and data acquisition systems. These PXI matrix modules are constructed using high reliability Sputtered Ruthenium Reed Relays, offering 109 operations to give maximum switching confidence with long life and stable contact resistance.
-
Product
PXI Solid State Switch Module, 6xSPST, 10 A
40-182A-011
Switch Module
The 40-182A-011 has 6 off high current SPST switches in two PXI slots and is part of our range of high power solid state switching solutions. Each SPST switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each SPST switch can support 10A of continuous current and switch up to 200V signals. The switch can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
PXI 20Amp 28Volt 2xSPDT Automotive Relay
40-181-011
Relay
Models 40-180/181 are High Power Relay Modules available with 2 SPST, 4 SPST or 2 SPDT contacts. They are capable of switching inductive/capacitive loads up to 40A at 14VDC or 20A at 28VDC. The 40-180/181 High Power Relay Modules are suitable for switching heavy loads or for slaving large external relays, contactors and solenoids. In particular these relay modules are designed for automotive test applications requiring the switching of D.C. voltage at high current. The 28V version is suitable for truck system test applications.
-
Product
2 Amp PXI Large Matrix Modules
BRIC™
-
Our 2 Amp PXI Large Matrix Modules use high-quality electromechanical relays to achieve their 2A switch rating. The BRIC structure allows the creation of large PXI matrices over multiple slots without the use of expensive external cables. The fully integrated programming interface represents the matrix as a single entity, easing user programming and reducing the likelihood of user errors.
-
Product
3U VPX 1 Slot P&G backplane with aperture for VITA 66.4
101V301P06-9X13
-
Power for 3.3V, 5V and 12V per VITA 46, with all rear connectors fully loaded. Use with Elma’s slot-to-slot or slot-to-I/O bulkhead cable products for system development.
-
Product
SOSA Aligned 1-Slot 3U VPX Development Chassis for Quartz Products
Model 8257A
-
- Ideal development platform for Mercury's- Model 5553 8-Channel A/D & D/A Zynq UltraScale+ RFSoC Gen 3 - Processor - SOSA Aligned 3U VPX- Model 5550 8-Channel A/D & D/A Zynq UltraScale+ RFSoC Processor - SOSA Aligned 3U VPX- Access to data and control planes provided through RTM- 1-slot, small footprint development chassis- Rear panel access to RF I/O, 100 GigE and chassis manager- Supports VITA-67.3C- Compatible with the Quartz product family- Pentek's Quartz Family of Xilinx Zynq UltraScale+ RFSoC FPGA Products Video- Live Signal Acquisition Video: Quartz Model 5950 and Model 6001 RFSoC boards- Pipeline Newsletter: Strategies for Deploying Xilinx's Zync UltraScale+ RFSoC- Please refer to the product datasheet for Installed FPGA IP Module details
-
Product
PXIe-5663E, 6.6 GHz PXI Vector Signal Analyzer
781259-01
Signal Module
6.6 GHz PXI Vector Signal Analyzer - The PXIe‑5663E offers wide instantaneous bandwidth and supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. You can use a PXIe‑5663E as either a spectrum analyzer or vector signal analyzer, and you can use it with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5663E can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5663E provides a low-cost solution to high-performance RF measurements.The PXIe-5663E comprises the following modules:• PXIe-5601 RF Signal Downconverter• PXIe-5622 IF Digitizer• PXIe-5652 RF Analog Signal GeneratorThere is no physical device named "PXIe-5663E".
-
Product
PXI EMC Filler Panel Kit, 5 Slots
Y1213A
-
Provides five single-slot PXI filler panels with EMC gaskets
-
Product
3U VPX Flash Storage Module Carrier
FSM-C
-
Curtiss-Wright Defense Solutions
The Flash Storage Module Carrier (FSM-C) provides rugged, removable, VITA 48.2 compliant, solid state storage in a 1” pitch, industry standard 3U VPX format. By providing a COTS storage solution, the FSM-C can lower schedule and technical risk for embedded storage applications.
-
Product
PXI Versatile Multiplexer, Solid State, 350mA, 60V
40-681A-001
Multiplexer Module
The 40-681A-001 is a very high-density versatile PXI Multiplexer module featuring a wide range of selectable switching configurations with 350mA current and 60V voltage handling. The 40-681A is especially useful where a high-density MUX array is required that can adapt to different test configurations for different test targets, or where a test system may have to be reconfigured in the future.
