Waveguides
guide the propagation of electromagnetic, light or sound waves.
See Also: Millimeter Waveguides, Optical Waveguides
-
Product
Double Ridged Waveguide Horn
DRH67
-
Frequency range: 6 GHz - 67 GHz VSWR (max): < 1.9:1Impedance: 50 O (Ohm)Connector: 1.85mm female Power (CW / Peak): 5W / 10 W
-
Product
Double Ridged Waveguide Horn
QRH67E
-
Frequency range: 6 GHz - 67 GHz VSWR (max): < 2.4 :1Impedance: 50 O (Ohm)Connector: 2x1.85 female Power (CW / Peak): 5W / 10 W
-
Product
Waveguide Rotary Joints
-
Waveguide Rotary Joints are used for the rotary transmission of power and signal between the stationary and rotating parts of a radar or satcom system.EVERAXIS has designed and produced single and multi channel Waveguide (WG) Rotary Joints since 1958. Every new design is simulated in FEM software as well as physically tested for optimal performance. Each high power Waveguide Rotary Joint is tested at maximum peak power before shipment.
-
Product
E- And W-Band Test Assembly
StormFlex® 047EW
-
An SF047EW assembly offers test engineers, application designers, manufacturers of mmWave applications the proven durability and robustness of Storm Flex® 047 cable, optimized for coaxial connectivity at frequencies up to 110 GHz.SF047EW cable can withstand handling and flexing and while maintaining the original Insertion Loss and VSWR performance at frequencies previously addressed by waveguides.
-
Product
Straight Waveguide Section
-
Straight sections are used to make connections between components in waveguide systems. Lengths and combinations are available on special order. VSWR is better than 1.1 over the full waveguide frequency band. Precision flanges on special order.
-
Product
Millimeter-Wave Noise Source, R-band, 26.5 to 40 GHz
R347B
-
The Keysight R347B noise source covers a 26.5 to 40 GHz frequency range. This waveguide noise source allows you to make accurate and convenient noise figure measurements on millimeter-wave devices. The R347B provides highly precise broadband noise at the input of the system or component under test. The noise figure meter then processes the ON/OFF ratio of noise power present in the system IF, and provides an accurate reading of noise figure and gain. The R347B noise source has remarkable ENR stability over time, which allows longer recalibration cycles and more accurate noise figure measurements.
-
Product
Waveguide Tunable Attenuators
-
*Low Insetion Loss*Full Waveguide Band Coverage*Precise Adjustment*High Maximum Attenuation
-
Product
60 GHz Development System
PEM009
-
The Pasternack / Vubiq 60 GHz development system provides rapid evaluation of Pasternack’s 60 GHz waveguide modules for quick prototyping for millimeter wave wireless system development. This high speed wireless 60 GHz developer kit is created from a partnership between Pasternack and Vubiq (pronounced “View-bik”), an industry expert in designing 60 GHz RF systems. Our 60 GHz wireless development systems make it easy to design new products and applications in the emerging unlicensed millimeter wave ISM V band.
-
Product
Integrated Couplers/ Harmonic Mixers
-
These waveguide bandwidth integrated coupler/mixers are designed to allow phase locking or signal monitoring of compact millimeter wave systems. RF inputs and outputs are on opposite sides of a thin wafer to obtain minimum insertion length. These devices use silicon Schottky barrier beam-lead diodes on a rugged stripline circuit. Nominal coupling value is 10 dB. For coupling values greater than 10 dB, non-directional coupler models are available (consult factory).
-
Product
Step Recovery Diodes
-
Macom Technology Solutions Holdings Inc.
MACOM’s Silicon and GaAs varactor multiplier diodes provide broadband performance ranging from 10 MHz to 70 GHz. They are ideal for multiplier circuits and are available in die form, plastic and ceramic packaging. These diodes boast a flip chip series for higher frequency millimeter wave applications; plastic packaged series for microwave frequency surface mount applications; ceramic packaged series for high power waveguide and coaxial applications.
-
Product
RF Coaxial Probes & Probe Positioner
-
Fairview Microwave’s line of coaxial RF probes and RF PCB probe positioner are ideal for use with chip evaluations, signal integrity measurements, coplanar waveguide, substrate characterization, gigabit SERDES and test fixture applications. The RF coaxial probes provide return loss better than 10 dB and a maximum operating frequency of 20 GHz. The probes have a 3.5mm female interface, a pitch of 800 or 1500 micron and they can be cable-mounted. They feature gold-plated contacts and can be used by hand, with or without a probe positioner. Compliant coaxial GSG (or GS) pogo pins allow for a broad range of probing angles. The RF PCB probe positioner can hold coaxial probes, has articulated joints and delivers multi-axis positioner control. This positioner also boasts a magnetic mounting plate with on-off positioner switch.
-
Product
NED-LMD Near-Eye Display Measurement Systems
NED-LMD WG Series
-
Gamma Scientific is introducing the NED-LMD Waveguide Tester as the world’s first specialized near-eye display measurement system that mimics human visual perception for fast, accurate and repeatable characterization of next generation optical waveguide-based Augmented/Mixed Reality displays and display components (light engine, waveguide, etc.). This comprehensive offering features a ‘robotic eye’ to help device manufacturers predict how the human eye would perceive their AR/MR displays, quantifying end user experience mapping the entire display field of view.
-
Product
Double Ridged Waveguide Horn
QRH50E
-
Frequency range: 5 GHz - 50 GHz VSWR (max): < 2.5:1Impedance: 50 O (Ohm)Connector: 2x2.40mm female Power (CW / Peak): 5W / 10 W
-
Product
Low Cost Microwave Wideband APD Preamp Receivers
MR11 (40KHz~18GHz)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
MR11 series microwave wideband optical receiver, adopts high Sensitivity APD diode and Low Noise Preamplifier IC, within bandwidth of 40KHz~18GHz, they are featured with excellent linearity, high responsibility and superior flatness of the RF response in both, power and phase. They provide an outstanding linearity fiber optical communication for analogue wideband microwave application. Due to avoidance of using expensive coaxial cable or wave-guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless, timing and reference signal distribution, telemetry, measurement and delay line etc as well as 10Gb/s high speed communication system.
-
Product
Coaxial Waveguide Adapter, 1.85 mm (m), 40 to 60 GHz
U281B
-
The Keysight U281B adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
Product
Double Ridged Waveguide Horn
H-A40
-
Frequency range: 26 GHz - 40 GHz VSWR (max): < 1.3:1Impedance: 50 O (Ohm)Connector: K female Power (CW / Peak): 15W / 30 W
-
Product
Microwave Switches
-
Communications & Power Industries
- Switches in waveguide, coax, stripline and microstrip- Designs are available from 20 MHz to 35 GHz- Power handling capability as high as 10s of Kilowatts peak- Integral driver, with BITE, can be supplied with any switch
-
-
Product
K-Band Waveguide Gunn Oscillator Module
FMWGN1001
-
FMWGN1001 is a K Band Waveguide Gunn Oscillator with a Center Frequency of 24.125 GHz and a Tuning Range of +/- 1.0 GHz. The unit has a Phase Noise @ 100kHz Offset of -95 dBc/Hz typ and Frequency Stability of -0.4 MHz/°C max. The Gun Oscillator has an Output Power of 10 dBm min and Power Stability of -0.04 dB/°C max. The Waveguide Gun Oscillator uses a Bias Voltage of 5.0 Volts and a Bias Current of 200 mA and has a Waveguide Size of WR-42 with a UG-595/U Flange.
-
Product
Waveguide Harmonic Mixer, 18 to 26.5 GHz
11970K
-
The Keysight 11970K waveguide mixer is a general-purpose harmonic mixer employing a dual-diode design to achieve flat frequency response and low conversion loss. These are achieved without external dc bias or tuning stubs. Manual operation and computer-controlled hardware operation are simplified because mixer bias and tuning adjustment are not required.
-
Product
Variable Attenuator
VAXE
-
The VAXE Variable Attenuators are waveguide components for tunable signal leveling or reflection compensation in waveguide networks. The Attenuators consist of waveguide section with a resistive film evaporated on the mica surface. The Attenuators has 0 ÷30 dB minimum attenuation range. The VAXE Attenuators are available in four waveguide bands between 33 GHz and 170 GHz.
-
Product
Rotary Joint
-
RF Lambda’s rotary joints are available in a variety of channels and configurations allowing the connection of waveguides and allowing for rotation of the different sections.
-
Product
In-Line Coaxial-to-Waveguide Adapter, 1.0 Mm (m) To WR-12, 60 To 90 GHz
E281DS
-
E281DS In-line 1.0 mm (m) - to- WR-12 waveguide adapter offers a simple way of measuring waveguide devices in E-band, 60 GHz to 90 GHz.
-
Product
Coaxial Receiver Protector
-
Where size, weight and power handling are the principle constraints, a TLM air-spaced coaxial limiter range provides an excellent compromise between waveguide and microstrip limiters. These devices are able to withstand higher power levels than microstrip solutions but still retaining a relatively compact package, Teledyne’s designs offer a low insertion loss and incorporate the same wide range of features as our waveguide limiters. Suitable for continuous operation at peak power levels of several kW's and mean power levels of 100's watts with sub- microsecond recovery time - over 10% bandwidth in <100mm length (at S-Band).
-
Product
Direct Reading Attenuator with Remote Control
DA2XE
-
DA2XE Millimeter-Wave Direct Reading Attenuator is a measurement instrument for signal level setting or loss measurements in waveguide networks. It also can be used for calibration of other attenuation measurement instruments. Direct Reading Attenuators have rotary-vane design. The value of attenuation is determined by rotation angle of resistive film with respect to the waveguide channel. Attenuation value does not depend on frequency. The attenuator has electronic control. The attenuator can be used in local or remote (via USB 1.1 or higher) operation modes.The Attenuators are provided in waveguide bands between 18 GHz and 225 GHz.
-
Product
Pre-Bonded Metalbacked PCB
-
Teledyne Labtech's significant in-house resources have the capability to satisfy the most exacting demands of complex pre-bonded PTFE Microwave PCB. Our extensive machine shop facilities allows Teledyne Labtech to offer a complete sourcing solution from low volume prototypes to high volume production requirements. Teledyne Labtech can also offer pre-bonded metalbacked PCB with integrated wave-guide transitions and co-planar wave-guides.
-
Product
Double Ridged Waveguide Horn
QRH18
-
Frequency range: 1 GHz - 18 GHz VSWR (max): < 2.5:1Impedance: 50 O (Ohm)Connector: 2xSMA female Power (CW / Peak): 100W / 170 W
-
Product
Waveguide Adapter
-
RF Lambda’s waveguide adapter product line is used to convert a waveguide interface to a coaxial interface. They come in a variety of frequencies, connector options and materials. They offer low insertion loss and VSWR as well as high power handling.
-
Product
Coaxial Waveguide Adapter, 2.4 mm (f), 26.5 to 40 GHz
R281A
-
The Keysight R281A adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
