CW Lasers
Continuous wave lasers output energy in pulses lasting in duration >0.25s.
-
Product
Fibolocator
-
Fibolocator is an innovative device for measuring and characterizing breaks and other backscattering-causing faults in optical fibers. Time-resolved correlation reflectometry is the principle on which the device is based. It analyzes the backscattered light like a pulse OTDR, but unlike such OTDRs, cw laser diodes are used. The requirements for the test signal and the complexity of the system are low, which leads to very low costs for OEM subsystems.
-
Product
Laser Head Cable, 3 m
10881A
-
Provide reliable power with this five-pin female DIN that connects the laser head to multiple laser boards.
-
Product
Laser Head Cable, 7 m
10881B
-
Provide reliable power with this five-pin female DIN that connects the laser head to multiple laser boards.
-
Product
Laser Head
5517DL
-
The Keysight 5517DL is used primarily in VME and PC based laser interferometer systems where the velocity of motion is faster, such as semiconductor lithography and flat panel applications. Please contact Keysight for custom requirements.
-
Product
Laser Head Cable, 20 m
10882C
-
The 10882C 20-meter Laser Head Cable is used to connect the 5519A/B Laser Head to the E1735A USB Axis Module for the 5530 Laser Calibration System.
-
Product
Four-Port Tunable Laser System Source
N7714A
-
The Keysight N7711A and N7714A tunable lasers are single-port and four-port sources, available with C-band or L-band wavelength coverage. The narrow linewidth and offset grid fine-tuning capability make them ideal sources for realistic loading of the latest transmission systems. All models can reach any wavelength point within their specified wavelength range just like all other Keysight tunable lasers. In this mode, code compatibility with existing test setups based on Keysight's range of full-size and compact tunable lasers is a great asset. In system loading applications, it may be preferable to grid-tune the lasers like system transmitters, simply by changing the channel index. The channel grid is adjustable to standard ITU-T grid spacing like 50 GHz, and to arbitrary grids. Likewise, the zero frequency (base channel) of the chosen grid is adjustable. A 12 GHz fine-tuning range allows de-tuning the frequency.
-
Product
Wavelength Meters - Scientific
-
Bristol Instruments'' wavelength meters are for scientists and engineers who need to know the exact wavelength of their lasers. These systems use proven interferometer-based technology to measure absolute wavelength to an accuracy as high as 0.0001 nm. To achieve the reliable accuracy that is expected from Bristol Instruments, all of its wavelength meters include a built-in wavelength standard for continuous calibration. Systems are available for CW and pulsed lasers that operate at wavelengths from 350 nm to 12 m.
-
Product
Tunable Laser Source - MATRIQ
-
The Laser 1000 Series is a fully-compliant micro-ITLA laser with up to four channels in a compact benchtop form factor.Offering 0.01 pm resolution tunability across C or L bands, exceptional power accuracy up to 16.5dBm, and optional dither suppression, this is a versatile and cost-effective general purpose instrument.
-
Product
HeNe Laser System with Built in Receiver and Power Supply
5519B
-
The Keysight 5519B Laser is a Helium Neon Laser (HeNe) that offers exceptional stability. The laser is a complete system with a built-in receiver and its own power supply that plugs directly into an AC power outlet.
-
Product
PCI Three-Axis High Performance Laser Board with External Sampling
N1231B
-
The Keysight N1231B PCI Three-Axis Laser Board with External Sampling is a register based PCI bus board that implements three axes of laser interferometer measurement for position monitoring and closed-loop servo control. There are four external sample inputs along with four data hold inputs that allow easy synchronization with user systems. Several threshold compare registers, with both hardware outputs and interrupt capability, can be used for travel limit and in window or out of window detection functions. The dual mode hardware position outputs, controlled by the hold inputs, provide either a 32-bits/axis parallel interface or a 36-bit multiplexed interface to the 36-bit axis position data at rates up to 20MHz. The user can programmatically access the externally sampled position and velocity data, as well as software sampled position and velocity data, over the PCI bus at rates up to 100kHz (3 axes of position and velocity) or 200kHz (position or velocity only).
-
Product
Laser Head
5517B
-
The Keysight 5517B is used primarily in VME and PC based laser interferometer systems where the velocity of motion is slower, such as machine tool applications. Please contact Keysight for custom requirements.
-
Product
Tunable Laser Source, High Power And Lowest SSE, Top Line
N7776C
-
The new Keysight N7776C top line tunable laser source is designed to reach best-in-class accuracy in static and swept operation for outstanding test efficiency. Two-way sweeps up to 200 nm/s speed with sub-picometer repeatability and without impacting the specified dynamic accuracy accelerate wavelength-dependent alignment processes and the automated calibration of wavelength-selective devices. Shorter time to testing and faster swept-wavelength tests help reduce test cost per device, improve test margins and lower the cost of ownership.
-
Product
Laser Head Cable, 3 m
10881D
-
Provide reliable power with this spade lug that connects the laser head to multiple laser boards.
-
Product
CW Power Measurement
-
Measure CW power from 10 MHz to 50 GHz at more than 17,500 readings per second over GPIB. Measure up to 90 dB with a single sensor, and select from a variety of high power sensors up to 50 W.
-
Product
Standard CW Amplifiers
-
The BT-AlphaA-CW series is a range of classAB RF power amplifiers covering the 10kHz to1MHz frequency range. Rugged, solid-state design - high reliability. Extremely high phase and amplitude stability. High linearity. In-Built Protection. Very fast blanking. Capable of pulsed operation. Competitively priced. Suitable for CW radar, communications, HF/VHF jamming, particle accelerator applications/plasma systems, plasma, RF heating and other scientific applications.
-
Product
CW Power Sensors
E-Series
-
Operates with the EPM, EPM-P and P-series power meters Wide dynamic range sensors (-70 to +20 dBm)Accurate CW average power measurements Wide frequency coverage from 10 MHz to 26.5 GHz (sensor dependent)Calibration factors stored in EEPROM
-
Product
PCI Three-Axis Laser Board
N1231A
-
The Keysight N1231A PCI Three-Axis Laser Board is a register based PCI bus board that implements three axes of laser measurement for position monitoring and closed-loop servo control. The hardware outputs, optimized for connection to a DeltaTau PMAC servo control system, provide parallel digital position data at rates up to 4MHz. The same position data along with velocity data is available over the PCI bus at rates up to 100kHz (3 axes of position and velocity) or 200kHz (position or velocity only).
-
Product
CW Transmitters
-
The Praxsym CW Transmitter is a complete, portable continuous wave test source. Used as an input source to test a distributed antenna system, the Praxsym CW Transmitter can provide test signals aiding in the design and optimization of in-building and outdoor networks.
-
Product
Laser
BDS-MM Series
-
*Pulse Width Down to 60 ps*Repetition Rate 20 MHz / 50 MHz*Free Beam or Fiber Output*Optical Power Up to 40 mW*All Electronics Integrated*No External Driver Unit*Simple +12 V Supply*40 mm x 70 mm x 120 mm
-
Product
Single Frequency CW 532 NM Laser up to 18W
EQUINOX
-
Equinox is a single frequency, 532 nm continuous wave laser designed for a range of scientific applications including pumping any Ti:Sapphire laser systems. It is engineered to meet the needs of experimentalists requiring high-performance systems with an emphasis on reliability, stability and ease of use. The laser incorporates pump diodes within the central unit and is fully automated with hands-free operation and control via ethernet, webpage and TCP/IP remote interface. This completely sealed system is inherently stable with low noise levels <0.05 % RMS and ultra-stable output powers with ±0.5 % stability. Equinox has options of high output power up to 18 W. Other major applications include mixing source, pump source for dye lasers and frequency doublers, optical tweezers, and biomedical imaging.
-
Product
Lasers
-
We design and manufacture advanced photonics tools for use in science, industry and education. Our lasers have enabled breakthroughs in quantum technology, biophotonics and chemical sensing and have been used by sectors as diverse as aerospace, defence, oil and gas, healthcare, food and drink. Known for their reliability and ease-of-use, our products such as SolsTiS, Sprite and Firefly are the tools of choice for researchers and innovators everywhere.
-
Product
High Resolution Laser Axis Board
N1225A
-
The Keysight N1225A provides ultra-sensitive fiber optic receivers and high resolution distance measurements for high performance positioning systems using laser interferometry with VME bus systems. Multiple N1225A boards can be linked together for up to 31 axes of position measurement. Includes "oscilloscope like" data capture operated with standard web browsers.
-
Product
Laser
BDS-SM Series
-
*Pulse Width Down to 60 ps*Repetition Rate 20 MHz /50 MHz / 80 MHz / CW (Switchable)*Free Beam or Fiber Output*All Electronics Integrated*No External Driver Unit*Simple +12 V Supply*40 mm x 70 mm x 120 mm
-
Product
Diode Lasers
6-Watt Blue Engraving Laser
-
Advanced Photonic Sciences LLC
Can be used in laser engraving, marking, and cutting applications. Process wood, plastics, metals, anodized aluminum, stone, tile, and other materials. The adjustable spot can be adapted to the needed distance from laser to the material. The spot, with a size of <100 μm, creates very fine engravings and sharp cutting edges. The built-in driver accepts TTL and analog signals for power adjustments. The laser can be controlled between 0% and 100% of output power. It comes preset and needs only a power supply and a signal source.
-
Product
Laser Microgage
PRO
-
The Microgage PRO is the next generation in laser measuring and alignment tools. Simplifying the inspection and alignment process, the microprocessor uses Smart data technology to equip its user with step by step instructions and easy to use data giving you the answers you need.
-
Product
Laser Rotators
-
Suitable for a wide range of applications, GeoMax rotating lasers are true multi-purpose tools.
-
Product
Laser Source
TW3104
-
Techwin(China) Industry Co., Ltd
Laser Source TW3104 is an essential instrument for optical network installation, trouble shooting and maintenance which can be used with an optical power meter for measuring optical loss in single-mode or multi-mode fiber cables. TW3104 is the earliest light source model in Techwin. It features compact size, high output power, stable output power and excellent wavelength stability .
-
Product
Laser Series
Jutze
-
Jutze laser marker series is equipped with Panasonic high-quality laser units. The laser unit, coupled with Z axis control, makes it capable of handling different thicknesses of PCBs & components. Adjustable range ± 3mm.
-
Product
Laser Systems
-
Laser systems (laser range finders, laser designators, laser receivers, laser trackers, laser pointers) are one of crucial technologies for defense/security sector. Laser systems have also found mass applications outside defense sector. Testing laser systems is needed for both manufacturers, maintenance workshops and final users for a set of different and important reasons. Hi-tech test equipment can help significantly in manufacturing, maintenance, training, purchase optimization, and optimal use of night vision devices.
-
Product
Laser Microgage
2D
-
The Microgage 2D laser alignment tool can be adapted to a wide variety of industrial measuring and alignment requirements. Each receiver measures in two axial directions (X & Y) and can be used for checking straightness, flatness, parallelism, squareness, bores, spindles, and other alignment needs.
