Isolation Amplifiers
-
product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J0
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
product
40V Multi-Output Isolated Topologies
Renesas' 40V multi-output isolated topology demonstration platforms use a single synchronous buck converter to realize multiple outputs (both inverting and non-inverting) as well as voltage step up/down function.
-
product
Analog Control Variable Gain Amplifiers (VGAs)
Analog Devices voltage controlled variable gain amplifiers provide continuous gain control over a wide dynamic range for a variety of audio and optical frequency bands. Our VGAs improve the dynamic range of a circuit by allowing users to adjust a signal’s amplitude in real time, which is invaluable for ultrasound, speech analysis, radar, wireless communications, and instrumentation-related applications.
-
product
Amplifiers
Amplifiers are used to amplify the energy output of photodetectors as well as convert their electrical signal for a number of illumination measurement or spectroscopy applications. Amplifiers are digital systems that amplify the low electrical current transmitted by photodetectors to easily detectable levels. Amplifiers also convert photodetectors' electrical current into voltage so that their signal may be read by other digital devices. Amplifiers are indispensable for nearly any light measurement applications by greatly increasing the usability of a detector system.
-
product
GHZ-Wideband Amplifiers
Ultra-wide bandwidth from 10 kHz up to 2.5 GHzGain up to 60 dB (x 1,000)Transimpedance gain with photodetectors up to 50,000 V/AVery low input noise down to 310 pV/√Hz (6.2 pA/√Hz)Integrated DC-current path for biased photodetector applicationsTwo identical signal outputs (HSA-Y series)DC-monitor output (HSA-Y series)
-
product
USB Isolators
USB isolators protect the communication interface between the host, such as a PC, and its peripheral. Utilizing iCoupler® digital isolation technology, Analog Devices offers USB 2.0 compliant SOIC components with data rates up to 12 Mbps that provide EMC protection and safety isolation, reduce design size and time, and lower system cost. Galvanically isolated USB μModule® (micromodule) transceivers integrate the USB interface with an isolated dc-to-dc converter for up to 2.5 W of isolated power and provide ±15 kV ESD. Whether for host, hub, bus splitter, or peripheral device, these transparent USB digital isolators are easy to use—they just work—all while meeting the demanding standards required for medical and industrial applications.
-
product
Amplifiers
Amplifier is designed to be used in conjunction with optional modules and can be confiugured for up to 8 inputs and 8 outputs. 9000 series modules as well as existing 900 series input modules can be used. The more appropriate modules can be selected depending on applications. Since it comes with two 60W power amplifiers, it can individually perform multi-origin braodcasts. It is equipped with singnal processing and control functions necessary for sound reinforcement, permitting all parameters to be set at the mixer. Settings data can be stored inside the unit and called up using the keys on the front panel.
-
product
C-Band Separate Raman Fiber Amplifier
RFA5000
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
-
product
PXI 5A Mux 2-Bank 24-Ch Isolated COM
40-651-012
This range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats: 1-bank 48-channel. 2-bank 24-channel. 4-bank 11-channel. 8-bank 5-channel.Connections are made via a front panel 50-way male D-type connector. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
product
Amplifier Module
LNAM-LPA
We offer an evaluation board and case for the LNAM-B and LNAM-FBX modules. This Laboratory PreAmplifier (LPA) solution is powered by a switch-mode power supply and gives access to the LNAM in- and outputs via BNC sockets.
-
product
ABex Rear Module with 8 Isolated Outputs and 5 Isolated Inputs
ABex RM-DIGIO
The ABex RM-DIGIO is a rear module for the ABex System. It is designed to connect digital signals to the back of a ABex chassis for example for cabinet control. As all IOs are isolated it’s possible to use different voltage levels for each IO.
-
product
Power Amplifier
5241
The Model 5241 is a voltage-controlled power amplifier designed exclusively for Magtrol's Model HD-825 Hysteresis Dynamometer. Because of its double braking system, the HD-825 requires more than 4 amps of power in order to reach full torque. The 5241 (which can provide up to 5 amps of output current) is necessary in order to amplify the power between a 6200 or DSP6001 Controller (which both have a maximum current output of 1 amp) and the HD-825 Dynamometer.
-
product
Digital Quad-Phase "DSP" Lock-In Amplifier -
eLockIn203
The eLockIn203 can be used as spectrum analyser, as oscilloscope, as sinus generator or as measurement control system.
-
product
Millimeter Wave Amplifiers
Ducommun offers Low Noise (ALN), High Power (AHP), Full Waveguide Band (AFB) and General Purpose (AGP) amplifiers to cover the frequency range from 18 to 96 GHz. These amplifiers utilize thin-film and microelectronics manufacturing techniques and are discrete and/or MMIC PHEMT devices based. These amplifiers feature low noise, high output power, single DC power supply and wide operation temperature range. The amplifiers are offered in two categories, standard and custom-built. Both standard and custom-built amplifiers are equipped with various RF interface, including standard waveguide or coaxial connector for convenient system integration. The optional input and output integrated isolators are available as an option to further improve the port return loss.
-
product
Distribution Amplifier
AVLINK TECHNIC TAIWAN CO., LTD.
Is a device that accepts a single input signal and provides this same signal to multiple isolated outputs.These devices are important because they allow a signal to be distributed to multiple destinations without ground loops or signal degradation. They are used for a number of common engineering tasks, including multiple amplification, cable television, splitting monitor and front of house mixes, and "tapping" a signal prior to sending it through effects units to preserve a "dry" signal for later experimentation.
-
product
High Voltage Isolator for Logic Analyzers
LX-08
The LX-08 series of high voltage logic analyzer adapters provides a safe isolated method of measuring high voltage control signals with a low voltage logic analyzer. All inbound signals are optically isolated and attenuated to a safe level for the delicate inputs typically found on logic analyzers. The inputs on the LX-08 are capable of withstanding voltages up to +/- 300V AC/DC, higher voltage configurations are available upon request. Rather than probing with multiple neon screwdrivers, the LX-08 can provide simultaneous viewing of up to 8 circuits in the STANDALONE mode via the indicator array. Need to catch a transient event or map out a timing sequence? Just add a logic analyzer to the outputs of the LX-08 and turn it into a high voltage logic analyzer. High voltage signals that were hazardous for a logic analyzer can now be measured safely. Typical outputs of a high speed PLC sequencer can be precisely timed and measured from both sides of the control relay. With the built in user selectable AC filter circuit, an AC signal can be measured as DC events or AC cycles.
-
product
Amplified Photodetectors
Hinds Instruments' photodetector modules are specifically designed for use with high frequency optical signals including those generated in Photoelastic Modulator (PEM) applications.
-
product
Distribution Amplifiers
High-performance distribution amplifiers (DAs) for sending digital or analog computer, video, audio, and data signals to multiple devices.
-
product
Fiber Pigtailed Tapered Amplifier
The AOSense tapered amplifier (TA) provides a coherent high-power beam, inheriting all properties from the seed source. TA’s are an essential optical component for quantum sciences, such as laser cooling and trapping, cold atom sensors, electromagnetically induced transparency, and quantum spectroscopy. The TA is also used in commercial laser modules, including master oscillator power amplifier (MOPA) lasers and external cavity lasers.
-
product
Hydrophone Booster Amplifier
Optional enhancement to the basic hydrophone measurement system to provide further amplification of the hydrophone signal.
-
product
Amplifier, Switch and Test Box
CLIOQC Model V
The QCBOX Model 5 is a non-conventional unit designed to fulfil actual and future needs of an electro-acoustical analyzer like the CLIO system. It is USB linked to a PC and can be configured, with dedicated software controls, to assist frequency response and impedance measurements or to perform DC measurements. Using it for frequency response measurements acts as 50W power amplifier to drive the speaker or network under test while routing one-of-four inputs to the analyzer as well the current sensing output. The four inputs are able to provide a phantom power supply both for Audiomatica or general purpose microphones (0-24 V range, software controlled). Impedance measurements can be done either switching the D.U.T.’s load across the analyzer’s input or using a dedicated output, ISENSE, thus allowing impedance measurements in constant voltage mode as well voice coil current distortion analysis. An internal ADC measures the DC current into the voice coil. Thanks to an internal software controlled voltage generator the speaker can be driven with a superimposed DC voltage (±20V), allowing for measurements of large signal parameters. Two ADC converters with a ±2.5 V and ±5 V are available at inputs 3 and 4 to measure the displacement with a laser sensor or any other DC signal. A dedicated digital input handles an external foot pedal switch (or TTL signal) to be connected and triggers QC operations. A 6 bit output – 5 bit input TTL digital port is available to interface the QCBOX and driving software with external hardware (like turntables for example).The QCBOX Model 5 finds use both in laboratory for R&D applications and in production lines setups.
-
product
1.5µm PM Fiber Amplifier ( PM EDFA )
HAPM4000
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HAPM4000 is a Polarization Maintaining Optical Amplifier which working in 1528~1563nm operating wavelength. Adopt Polarization Maintaining Erbium-doped fiber (PM-EDF), output optical power range 13~26dBm, extinction ratio >20dB.
-
product
Panel-mounted Power Amplifier For Network Simulators
PAV250Bi
PAV250Bi is one of the conventional voltage power amplifier model, which is specially designed for R&D of power system simulation.
-
product
Power Amplifiers
In this product category you find highly linear power amplifiers for digital and analog data transmission, power amplifiers for CW applications and for laboratory use, which stand out due to its liability, robustness and long-term availability and which are based on the semiconductor technologies which are actually available on the market.
-
product
Low Noise Amplifiers
Our range of ITAR Free, Low Noise Amplifiers (LNAs) cover a wide range of applications but are primarily suited to communication systems including both Data-Link and Satellite Communications (Satcom) systems. Our new K-Band LNA operates over a 19.2 - 21.2 GHz with 1.3 dB Noise Figure at 25°C. It is configured with a waveguide input and 2.92 output connector all in a hermetic package.
-
product
Amplifiers
Packaged and Die up to 26 GHzOver 145 MMIC Surface Mount and Die modelsConectorized models, power output to 100WHigh dynamic range, low noiseLow-cost, custom solutions available!
-
product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K1
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
product
PXI 5A Power Multiplexer, 1-Bank, 48-Channel, Isolated Common, Independent Isolation
40-651A-111
The 40-651A-111 is part of our range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats.
-
product
3-Ch Sensor Amplifier
PS-1300
The PS-1300 3-Ch Sensor Amplifier is designed to be compact and light weight, and able to be used in combination with a tri-axial accelerometer. Each channel can also be used independently and connected with a single axis accelerometer. The PS-1300 has built-in integration function and enables to optimize the input signal to vibration data analysis devices connected.
-
