Manipulators
1) hold test heads for docking. 2) hold probes for positioning.
-
Product
3-DOF Simulation Table
KRD60 series
-
KRD60 Series 3 DOF simulation table simulates various mechanical, electrical, and electronic products installed on ships, seaplanes, and other equipment to perform sway and tilt tests to determine the ability and structural integrity of the product to withstand severe sway and tilt requirements. The tilt test is mainly applicable to large-angle tilt caused by ship damage, manipulation, imbalance in loading and unloading, and wind. The sway test is mainly applicable to long-term swaying of the ship due to external forces such as wind and waves, which must be maintained normally or products that work reliably, and products that have a significant impact on their performance in a rocking environment.
-
Product
NI-9853, CAN Interface Module
780178-01
CAN Interface
2-Port, High-Speed C Series CAN Interface Module—The NI‑9853 is a high-speed Controller Area Network (CAN) interface for developing FPGA-based applications with the NI‑RIO driver on CompactRIO. The NI‑9853 is ideal for low-level FPGA‑based control and triggering applications that are programmed using the LabVIEW FPGA Module. The NI‑9853 is ideal for byte-level manipulation of CAN frames using the LabVIEW FPGA Module. The NI‑9853 is only compatible with CompactRIO systems.
-
Product
sbRIO-9860, Non-Enclosed, 2-Port, C Series Vehicle Multiprotocol Interface Module
787325-01
Interface Module
Non-Enclosed, 2-Port, C Series Vehicle Multiprotocol Interface Module - The sbRIO-9860 is a hardware-selectable HS/FD controller area network (CAN) and/or local interconnect network (LIN) interface for developing CAN and/or LIN applications. As part of the NI-XNET product line, the sbRIO-9860 works well for applications requiring high-speed manipulation of hundreds of frames and signals while performing low-level FPGA control and embedded monitoring in the same CompactRIO Single‐Board Controller. Non-enclosed modules are available for OEM applications.
-
Product
Precision Capacitance Meter
TH2638A
-
Changzhou Tonghui Electronic Co., Ltd.
TH2638 series is a new precision capacitance meter with higher test frequency. With small size and portable appearance, it is convenient for use on the shelves. With basic accuracy of ±0.07%, loss accuracy of 0.0005, test frequency up to 1MHz, 4.3-inch LCD screen, selectable Chinese-English operation interface, TH2638 series is easy to operate and provide fast and reliable test for ceramic capacitor production. Also, it can test all kinds of capacitors from low value to high value. The results of testing one capacitor for several times are quite stable and accurate, even for lower value capacitors. The tester is compatible with SCPI command set, and configured with manipulator and scanner interface, the scanner interface can scan the open/short/ load error calibration in each channel, 256 channels at most. In low frequency, there is signal level compensation function. When the impedance is very small, the internal resistance in signal source and test cable will cause the voltage on terminal of DUT lower than the set range, then this function will adjust the level to the set range.
-
Product
Mechanical Test Head Housing
-
a result of more than 10 years' experienceavailable with integrated manipulatorfully integrated docking and board lockingtest housing mechanics design as per customer specificationssuitable for individual and high-volume productionstandard and customized dimensionsno limitation in size and electrical power capacitiesquick and easy locking and unlocking process for board changelarge application space load boardoptional number of channel boards as per customer specificationsfamily/DUT board connection achieved by high-end double-ended spring probes - 50 Ohmhigh-end cooling fansfacilitated adaptation with all available manipulator solutionsdocking design in compliance with customer internal docking standards/dimensionsdocking force as per customer specificationscenter of gravity fully compensated
-
Product
Pulsed And CW EPR/ESR: Synthesizers Up To 280 GHz
-
Insight Product Company offers synthesizers at frequencies from 30 to 280 GHz which can be used in EPR/ ESR experiments. These sythnesizers are designed to go swiftly from the generation to the non-generation mode and back. This process is controlled by external TTL signal. There is also the possibility to manipulate the phase, namely to shift it by 90 degrees and 180 degrees. ON/OFF switch time is approximately 2 nanoseconds.
-
Product
Ethernet and Fibre Channel Test Platform
SierraNet M648
Test Platform
The SierraNet M648 Ethernet and Fibre Channel test platform provides best in class analysis, jamming and generation for traffic capture and manipulation for testing application and link characteristics. SierraNet M648 is the latest in the line of industry leading test and measurement tools from Teledyne LeCroy, designed for today’s high-speed storage and communications fabrics. SierraNet M648 supports examination and modification of Ethernet and Fibre Channel links utilizing both Pulse Amplitude Modulation 4 (PAM4) and legacy Non-Return to Zero (NRZ) technologies.
-
Product
Software
SIGNAL 5
-
provides a graphical environment for viewing, measuring, and manipulating signals combined with an extensive mathematical toolbox and advanced programming capabilities.
-
Product
NI-9862, CAN Interface Module
781639-01
Interface Module
1-Port, High-Speed, Flexible Data Rate C Series CAN Interface Module—The NI‑9862 is a high-speed Controller Area Network (CAN) Flexible Data‑rate (FD) interface for developing applications with the NI‑XNET driver. The NI‑9862 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. You can perform this manipulation while taking other data acquisition measurements in the same NI CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same NI CompactRIO chassis.
-
Product
PXI-8516, 2-Port PXI LIN Interface Module
781366-01
LIN Interface
2-Port PXI LIN Interface Module—The PXI‑8516 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver.The PXI‑8516 excels in applications requiring real-time, high-speed manipulation of hundreds of LIN frames and signals, such as hardware-in-the-loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move LIN frames and signals between the interface and the user program without CPU interrupts, minimize message latency, and free host processor time for processing complex models and applications.
-
Product
Optical Tweezers
PicoTweezers
-
Single or dual beam optical tweezers system based on an inverted microscope • 3D real-time video-based force measurements with sub-pN resolution • Huge free space above optical trap for all kinds of sample chambers and carriers • Manipulate and navigate trapped objects with nanometer precision • Easily extendable to fluorescence, STED, Raman spectroscopy, TIRF, or CLS.
-
Product
PCI-8513, 2-Port, Software‑Selectable/FD CAN Interface Device
780684-02
CAN Interface
2-Port, Software‑Selectable/FD CAN Interface Device—The PCI‑8513 is a controller area network (CAN) flexible data-rate (FD) interface for developing applications with the NI‑XNET driver. NI‑XNET software-selectable CAN interfaces offer the best flexibility for CAN development with onboard transceivers for high-speed/FD, low-speed/fault-tolerant, and single-wire CAN as well as any external transceiver. The PCI‑8513 excels in applications requiring real‑time, high‑speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts.
-
Product
USB-8502, 2-Port, High-Speed/FD, USB CAN Interface Device
784662-01
CAN Interface
1- or 2-Port, High-Speed/FD, USB CAN Interface Device—The USB-8502 is a high-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8502 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8502 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
Hardness & LSI Titration Kit
Ultrameter™ III 9PTKB
-
The Ultrameter III 9P™ AHL Titration Kit, is based on the tried and tested design of the Ultrameter II™. The 9P adds the ability to perform in-cell alkalinity and hardness titrations either as stand-alone measurements or as part of an LSI calculation. Alkalinity, hardness, pH and temperature values can be manipulated in the LSI calculator to predict the effect of changes on water balance. Measurements are extremely accurate. And the 9P is simple to operate and maintain.
-
Product
Software
DASYLAB Lite
-
Dasylab lite software for operation of our line of THERMES Data Acquisition Systems. For customers who already have Labview or Dasylab no additional software is necessary. Recommended operating software is Dasylab Lite version 10. The lite version provides all the necessary functions to display and store temperature data in digital and graphical formats in real time. Users may customize the display to suit their particular application. The Dasylab Basic version provides additional features for data manipulation and statistical analysis.
-
Product
Terahertz Synthesizer 0.45 THz to 2.85 THz
-
Advantages: -Significant output power -Extremely stable frequency -Wide tunability -Wide possibility of frequency and amplitude modulation and manipulation, -Convenient for heterodyne and direct detection receiver systems -Ease of control and operation -High reliability
-
Product
Laser Systems
-
Exail is committed to develop and manufacture performant and reliable optical components, and to have them integrated into turn-key laser systems for the most challenging applications: sensing, QKD or cold-atom manipulation.
-
Product
Manual Media Analysis Solutions
-
Truly one tool to view them all. The Ultimate Analyzing Tool for manual in-depth analysis, verification and validation of various file formats and containers. Metadata extraction and stream manipulation available.
-
Product
USB-8506, 1-Port, USB LIN Interface Device
784663-01
LIN Interface
1- or 2-Port, USB LIN Interface Device—The USB‑8506 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver. The USB‑8506 is powered over the USB bus and does not require external power. The USB‑8506 excels in applications requiring logging or manipulation of hundreds of LIN frames and signals, such as in-vehicle data logging, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move LIN frames and signals between the interface and the user program without CPU interrupts, minimize message latency, and free host processor time. The USB‑8506 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
USB-8502, 1-Port, High-Speed/FD, USB CAN Interface Device
784661-01
CAN Interface
1- or 2-Port, High-Speed/FD, USB CAN Interface Device—The USB-8502 is a high-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8502 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8502 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
Universal Manipulator
LSC
-
The LSC is a versatile universal manipulator, compatible with probers, vertical plane handlers, and dock-from-below test systems.
-
Product
sbRIO-9866, Non-Enclosed, 1-Port C Series LIN Interface Module
785965-01
LIN Interface
Non-Enclosed, 1-Port C Series LIN Interface Module—The sbRIO‑9866 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver. The sbRIO‑9866 excels in applications requiring real-time, high-speed manipulation of hundreds of LIN frames and signals such as hardware‑in‑the‑loop (HIL) simulation, rapid control prototyping, bus monitoring, automation control, and more. You can perform this manipulation while taking other DAQ measurements in the same CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same CompactRIO Chassis. Non-enclosed modules are designed for OEM applications.
-
Product
Probe Station
EPS500
-
Reasonable price and compact design. - Sellectable chuck size : 4inch, 6inch, 8inch when ordering probe station. - Hot chuck can be installed. Temp range: RT ~ 300°C - Hot and cool chuck from 0 °C ~ 300 °C can be provided. - Maximum 6pcs of manipulators can be installed on the base unit of probe station EPS500.
-
Product
Ultra High Performance 3D CT System
UltraTom
-
3D micro-tomography (CT Scan) and nano-tomography. Modular system with multiple imagers and x-ray generators. Experimentations possible in-situ. Large volume Inspection and manipulation volume.
-
Product
Universal Manipulator
LS
-
Manage the rapidly changing production environment and achieve the lowest cost of test, converting between probe, final, engineering and service positions with ease. Rapid advancements in semiconductor test technology have resulted in highly efficient test cells, capable of device test throughputs far greater than ever before.
-
Product
MuClock
-
Our Muclock is the only commercially available time & frequency reference based on quantum manipulation of laser cooled atoms in the world. This unique solution is the result of more than 15 years of experience acquired by our academic partner, LNE-SYRTE, one of the major international experts in the field of time standards.
-
Product
3D Software
Geomagic Wrap
-
Geomagic Wrap 2017 delivers a new and improved 3D scan-to-model workflow. From expanded file format support to manipulating texture maps for bringing your printed parts to life, the 3D scan data toolbox of Geomagic Wrap provides a wealth of possibilities.
-
Product
SpaceWire Physical Layer Tester
141
-
The SpaceWire Physical Layer Tester (SPLT) is a tool designed to test, validate and verify a SpaceWire system across all levels of the SpaceWire standard. Two SpaceWire ports employ a special LVDS interface which allows the transmitted signals to be deliberately and measurably manipulated to test the capability of a unit under test to receive signals of varying quality.
-
Product
Safety Locking Devices
-
Leuze electronic GmbH + Co. KG
Safety switches with locking device keep doors locked and thus prevent unauthorized entry or access, thereby protecting persons and processes. The L series features a wide range of variants for different application cases, from devices with mechanical actuators to devices with an RFID‑coded actuator for maximum manipulation protection as well as integrated command buttons. With their robust design, all devices are designed for rough industrial applications.
-
Product
Vehicle Multiprotocol Interface Module
C Series
Interface
C Series Vehicle Multiprotocol Interface Modules use hardware-selectable NI-XNET Transceiver Cables (TRC) to communicate High-Speed/Flexible Data‑Rate CAN, Low-Speed/Fault Tolerant CAN, and/or LIN. Using the NI-XNET driver, you can create applications that require real-time, high-speed manipulation of hundreds of CAN and/or LIN frames and signals. The NI-XNET device-driven DMA engine enables the onboard processor to move frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time. C Series Vehicle Multiprotocol Interface Modules work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
