T1
A phone line connection with data rates of 1.544Mbits per second over 24 channels running at 64Kbs.
See Also: E1
-
Product
PXI/PXIe 1000Base-T1 Dual Multiplexer With Fault Insertion, Dual Channel
40-204-002
Multiplexer Module
The 40-204-002 (PXI) and 42-204-002 (PXIe) are dual channel differential multiplexers designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They are available with support for 1 or 2-channels of two wire serial interfaces. Each channel pair can be looped out to external equipment or the switches can be used simulate a channel open fault. Using the fault bus, switches can simulate a short between both wires or a short to one of two externally applied fault conditions – such as battery supply or ground - via two fault buses.
-
Product
PXI/PXIe 1000Base-T1 Dual Multiplexer With Fault Insertion, Single Channel
42-204-001
Multiplexer Module
The 40-204-001(PXI) and 42-204-001 (PXIe) are single channel differential multiplexers designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They are available with support for 1 or 2-channels of two wire serial interfaces. Each channel pair can be looped out to external equipment or the switches can be used simulate a channel open fault.
-
Product
4 Port T1/E1/PRI ISDN Simulator
SIM-4PRI
-
The most inexpensive ISDN simulator on the market. This unit has four PRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network.
-
Product
PXI/PXIe 1000Base-T1 Dual Multiplexer With Fault Insertion, Dual Channel
42-204-002
Multiplexer Module
The 40-204-002 (PXI) and 42-204-002 (PXIe) are dual channel differential multiplexers designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They are available with support for 1 or 2-channels of two wire serial interfaces. Each channel pair can be looped out to external equipment or the switches can be used simulate a channel open fault.
-
Product
8 Port T1/E1/PRI Bulk Call Generator
BCG-8PRI
-
This unit has eight PRI ports allowing to generate real calls to a T1/E1/PRI connected device for the stress-test. It can be used to generate call volume to VoIP geteways, PBXs, Fax servers, RAS serves.
-
Product
2 Port T1/E1/PRI ISDN Simulator
SIM-2PRI
-
The most inexpensive ISDN simulator on the market. This unit has two PRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network.
-
Product
1000BASE-T1 MEDIACONVERTER
Art.-Nr.: TE-1401-1
-
The ideal physical layer conversion between Automotive Gigabit Ethernet and your PC system The 1000BASE-T1 MediaConverter establishes one direct point-to-point conversion between automotive ECU’s using 1000BASE-T1 and any standard Gigabit Ethernet device with RJ-45 connector.
-
Product
PXIe-8523, 4-Port, 100/1000BASE-T1 PXI Automotive Ethernet Interface Module
787311-01
Ethernet Interface
PXIe, 4-Port, 100/1000BASE-T1 PXI Automotive Ethernet Interface Module - The PXIe-8523 is a 100/1000BASE-T1 unshielded twisted pair (UTP) PXI Automotive Ethernet Interface Module for developing applications with the NI‑XNET driver. With this hardware, you can develop applications … that require Automotive Ethernet to test and validate automotive electronic control units (ECUs). The PXIe-8523 provides up to four independent endpoints or up to two network terminal access points (TAPs). It features onboard hardware timestamping and can act as up to four separate 802.1AS masters or slaves, so it can synchronize with an external network as well as the rest of a PXI system. The PXIe-8523 also provides LEDs on the front panel to help you monitor the network link and activity.
-
Product
VTAC Patchcord, Receiver, 36", VTAC, 2x 1000Base-T1 UTP Wire 1 Port MateNet, 1 Position
7-142716763-036
VTAC Patchcord
VTAC Patchcord, Receiver, 36", VTAC, 2x 1000Base-T1 UTP wire 1 Port MateNet, 1 Position.
-
Product
1000BASE-T1 SFP Module
Art.-Nr.: TE-1437
-
Convert between 1000BASE-T1 (automotive Gigabit Ethernet) and SGMII Interface. The 1000BASE-T1 SFP Module is the cutting-edge solution to convert between 1000BASE-T1 and SGMII. It fits into a standard Small Form-factor Pluggable (SFP) and generates 1000 Mbit/s full-duplex.
-
Product
PXI 10GBase-T1 Ethernet MEMS Fault Insertion Switch, 8 Channel
40-205-008
Fault Insertion Unit
The 40-205-008 (PXI) is a 8-channel fault insertion switches designed to simulate common faults on high speed two wire communication interfaces such as xBaseT1 Ethernet. They available with 4 or 8 channels of two wire serial connections and can be used for simulating faults on 10BaseT1, 100BaseT1, 1000BaseT1 and 10GBaseT1 Ethernet interfaces. Any wire can be set as open circuit and shorts can be applied across wire pairs. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to supply voltage or ground.
-
Product
ISDN Chip Set
Emutel Symphony
-
Emutel Symphony is a convenient and flexible Basic Rate ISDN, Primary Rate ISDN and Analog PSTN network simulator. With support for S, U, E1, T1 and PSTN analog interfaces you can use the Emutel Symphony to test and develop a full range of ISDN(E1/T BRIS BRIU) and PSTN analog (FXS) equipment.
-
Product
100BASE-T1 SPY 12 PORT
Art.-Nr.: TE-1500
-
Capture the traffic of 100BASE-T1, CAN/CANFD, LIN and Flexray Buses using only one device. The 100BASE-T1 SPY 12 port is a highly specialized test and evaluation tool for seamless capture of multiple in-vehicle-network technologies. It provides common timestamping of all incoming messages and delivers the traffic via Standard Gigabit Ethernet.
-
Product
PXI/PXIe 1000Base-T1 Fault Insertion Switch, 3-Channel
42-203-001
Fault Insertion Unit
The 40-203-001 (PXI) and 42-203-001 (PXIe) are designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They support 3 channels of two wire serial interfaces. Each channel pair can simulate an open fault in either or both wires, and using the fault bus switches can simulate short between both wires or a short to one of two externally applied fault connections – such as battery supply or ground - via two fault buses.
-
Product
PXIe-8521, 4-Port, 100BASE-T1 PXI Automotive Ethernet Interface Module
786771-01
Ethernet Interface
PXIe, 4-Port, 100BASE-T1 PXI Automotive Ethernet Interface Module - The PXIe-8521 is a 100BASE-T1 unshielded twisted pair (UTP) Automotive Ethernet interface for developing applications with the NI‑XNET driver. The PXIe-8521 is ideal for developing applications that require … Automotive Ethernet to test and validate automotive electronic control units (ECUs). The interface provides up to four independent endpoints or up to two network terminal access points (TAPs). It features onboard hardware timestamping and can act as up to four separate 802.1AS masters or slaves, which allows it to synchronize with an external network as well as the rest of a PXI system. The PXIe-8521 also provides LEDs on the front panel so that you can monitor the network link and activity.
-
Product
100base-T1 Ethernet (BroadR-Reach®) Logging Expansion With Low Latency
PT-15B
-
The PT-15B expands the PM-200 data logger from the Power Family by adding twelve 100base-T1 interfaces. Ethernet traffic is looped through the device with constantly low latency irrespective of the frame length. This means that the time synchronization protocols of the logged Ethernet interfaces are not affected. 100base-T1 packets are time stamped, filtered and sent to the PM-200 data logger via a 1000base-T interface.
-
Product
WAN Tester II
-
The Telinc WAN Tester II is a sophisticated bit error rate tester in a compact, hand held package. It can test a wide variety of communications facilities and equipment including DDS, T-1, fractional T-1, E-1, fractional E-1, T-3 and E-3 NTUs, multiplexers, CSU/DSUs, T-1 CSUs, DTUsand TIUs. It includes a speaker to listen to voice in a DS0. It is supplied with changeable nickel metal hydride batteries and a built-in charger.
-
Product
VTAC Patchcord, Receiver, 72", VTAC, 2x 1000Base-T1 UTP wire H-MTD Cable Jack, 1 Slot
7-142716765-072
VTAC Patchcord
VTAC Patchcord, Receiver, 72", VTAC, 2x 1000Base-T1 UTP wire H-MTD Cable Jack, 1 Slot.Note: Static Bend Radius - 19.2mm [.76in], Flex Bend Radius - 48mm [1.89in]
-
Product
PXI/PXIe Trigger Module
PXT1741
Trigger Module
The PXT(e)1741 Trigger Module ist designed to build up a connection between trigger signals from any external trigger source (5V TTL Standard) and the PXI(e) trigger bus. Therefore the device is equipped with four SMA front connectors (T1 to T4).
-
Product
Voice Monitoring
VOIP Echo
-
*The Voice Band Analyzer (VBA) is an analysis tool for monitoring the quality of voice band traffic (including hybrid echo) over VoIP, TDM and wireless networks*VBA works in conjunction with GL's TDM, Packet, and Wireless non-intrusive capture products, such as T1 and E1 Call Capture and Analysis, VoIP PacketScan&trade, and GSM, CDMA, and 3G Call Capture Products. VBA instantly detects voice file captures and with appropriately installed analysis modules, monitors speech levels, noise levels, and hybrid echo. Other analysis modules such as ITU-T P.561, P.562, P.563, fax and modem analysis, and many others can be hosted as plug-ins.*The VBA application can also operate on pre-captured files. It supports A-Law, µ-Law, 16-bit PCM (Intel), 16-bit PCM (Motorola) and MS Wave file formats.*Required software PKV100 and VBA032 at each probe location and PKV170 PacketScanWEB - Network Surveillance Software*Required hardware - 1U rack PC with sufficient hard disk for capturing over 10,000 calls (80 GB HD) for each VBA colocated with a probe*Additional hardware - PC for PKV100 PacketScan™ Software
-
Product
Digital And Analog Call Simulation
-
GL’s T1 E1/Analog Test Suite supports analysis and emulation of legacy protocols (MFCR2, E&M, SS1/SS4, SS5, Voice Call Signaling, 2-wire Call, SF Signaling (DTMF)) applicable to Federal Aviation Administration "FAA" within their National Airspace System "NAS" Ground-to-Ground Air Traffic Control Network and Voice System (NVS) to Analog Interphone.
-
Product
2 Port T1/E1/PRI + 8 Port FXS PSTN
CH-8FXS-MOD-2PRI
-
One of the most feature rich PSTN simulator on the market. Unit has 8 analog phone lines (FXS) making it a perfect tool for testing VoIP gateways, IVR, V.90 modems, RAS servers, audio conference bridges or anything that requires analog phone lines. 2 port T1/E1/PRI module provides non-blocking switching among FXS ports and any of T1/E1/PRI B-channels or Time slots.
-
Product
1000BASE-T1 Ethernet Logging Expansion With Low Latency
PT-20MG
-
The PT-20MG expands the PM-200 data logger from the Power Family by adding six 1000BASE-T1 automotive gigabit Ethernet interfaces. Ethernet traffic is looped through the device with constantly low latency irrespective of the frame length. This means that the time synchronization protocols of the logged Ethernet interfaces are not affected. 1000BASE-T1 packets are time-stamped, filtered and sent to the data logger via a 1000BASE-T interface.
-
Product
In-Service Electrical Continuity Test Card
Cisco ONS 15454
-
The Cisco ONS 15454 In-service Electrical Continuity Test Card is a solution for confirming proper DS-1 and DS-3/EC-1 cabling between the Cisco ONS 15454 shelf assembly electrical interface adapter (EIA) panels and the user's patch panels. The solution is designed for shelf installations that are presently carrying traffic and tests for common wiring errors including electrical shorts, opens, wrong connections, and tip/ring reversals.
-
Product
8 Port T1/E1/PRI ISDN Simulator
SIM-8PRI
-
The most inexpensive ISDN simulator on the market. This unit has eight PRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network.
-
Product
1000 BASE-T1 Ethernet
-
Compact, powerful computers and servers support diverse smart city applications at edge points.
-
Product
2 Port T1/E1/PRI Bulk Call Generator
BCG-2PRI
-
This unit has two PRI ports allowing to generate real calls to a T1/E1/PRI connected device for the stress-test.
-
Product
WAN Tester III
-
The Telinc WAN Tester III is a sophisticated bit error rate tester in a compact, hand held package. It can test a wide variety of communications facilities and equipment including T-1, fractional T-1, E-1, fractional E-1, T-3 and E-3 modems,multiplexers, CSU/DSUs, T-1 CSUs, DTUs, NTUs and TIUs. It is supplied with user changeable nickel metal hydride batteries and a built-in charger.
-
Product
Ultra-compact Laser Collimated Beam Sensor
HL-T1
-
Panasonic Industrial Devices Sales Company of America
The HL-T1 Sensor is an ultra-small laser Thru-Beam Sensor with very high resolution.
-
Product
Breakout Box
T1000-15
-
T1000-15 breakout box with dual 15 pin D-Sub connectors for signal capture or monitoring. Dual connectors provide a total of 30 test points plus a ground jack. All test points use standard size 4mm banana jacks. Test points may be connected using shorting banana cable to allow signal continuity. Ideal for continuity measurements, isolation testing, and signal capture.
