T1
A phone line connection with data rates of 1.544Mbits per second over 24 channels running at 64Kbs.
See Also: E1
-
product
T1 E1 Testing
T1/E1 carriers are used extensively throughout the world for carrying large volumes of call containing both voice and data. Their popularity can be attributed to their high reliability, manageability and flexibility. The available digitized channels, 24 for T1 and 32 for E1 can be used for carrying voice and/or data. Further, the carriers can be used separately or they can be combined in order to provide higher transmission bandwidth.
-
product
850NM T1 3/4 Phototransistor
350-00029
This phototransistor responds to visible light as well as the lower infrared range.
-
product
PXIe-8523, 4-Port, 100/1000BASE-T1 PXI Automotive Ethernet Interface Module
787311-01
PXIe, 4-Port, 100/1000BASE-T1 PXI Automotive Ethernet Interface Module - The PXIe-8523 is a 100/1000BASE-T1 unshielded twisted pair (UTP) PXI Automotive Ethernet Interface Module for developing applications with the NI‑XNET driver. With this hardware, you can develop applications … that require Automotive Ethernet to test and validate automotive electronic control units (ECUs). The PXIe-8523 provides up to four independent endpoints or up to two network terminal access points (TAPs). It features onboard hardware timestamping and can act as up to four separate 802.1AS masters or slaves, so it can synchronize with an external network as well as the rest of a PXI system. The PXIe-8523 also provides LEDs on the front panel to help you monitor the network link and activity.
-
product
Low Voltage Test System
CKT T1
The CKT T1 is a compact size solid-state test system featuring 128 test points.
-
product
E1 T1 Tester
NetProbe 2000 PDH
New Generation Analyzer for Legacy PDH networksThe NetProbe 2000 E1E3 is newest, state-of-the-art handheld analyzer on the market for testing the legacy E1 and E3 in PDH networks. It includes all features for E1 & E3 BERT and E1 physical layer testing. Automated line monitoring performs autocheck of essential alarms and errors.
-
product
Digital And Analog Call Simulation
GL’s T1 E1/Analog Test Suite supports analysis and emulation of legacy protocols (MFCR2, E&M, SS1/SS4, SS5, Voice Call Signaling, 2-wire Call, SF Signaling (DTMF)) applicable to Federal Aviation Administration "FAA" within their National Airspace System "NAS" Ground-to-Ground Air Traffic Control Network and Voice System (NVS) to Analog Interphone.
-
product
Media Gateway
A Media Gateway is a networking device that provides valuable and essential functions for organizations, service providers, and network operators. When interconnecting traditional time-division-multiplexed (TDM) telephony systems with modern voice-over-internet protocol (VoIP) systems, a VoIP media gateway works by providing protocol conversion (translation) and interoperability between the two network technologies. Also known as an IP media gateway or SIP media gateway, the device converts a traditional analog plain-old-telephone-system (POTS) voice signal or related digital telephony signals such as T1, DS3, STM1 or OC3 into packets for transmission over a data network such as the Internet, private IP Network or a corporate LAN. When the legacy system is based on digital integrated services digital network (ISDN) technology, the device may be called a digital VoIP gateway or ISDN media gateway. Some manufacturers combine gateway functionality with WAN-access (internet-access) capability into a single device or network appliance. Such a dual-purpose device may be known as an access media gateway.
-
product
WAN Tester III
The Telinc WAN Tester III is a sophisticated bit error rate tester in a compact, hand held package. It can test a wide variety of communications facilities and equipment including T-1, fractional T-1, E-1, fractional E-1, T-3 and E-3 modems,multiplexers, CSU/DSUs, T-1 CSUs, DTUs, NTUs and TIUs. It is supplied with user changeable nickel metal hydride batteries and a built-in charger.
-
product
New Generation Analyzer For IEEE C37.94
NetProbe 2000 C37.94
The NetProbe 2000 C37.94 is a field analyzer with IEEE C.37-94 Multimode optical fiber interface for testing bit error preformance between teleprotection and digitalMultiplexer equipment. Can be combined with many optional interfaces for T1,E1, WiFi, VoIP and V-series testing.
-
product
Infrared T1 3/4 LED
350-00003
T1 3/4 Infrared light emitting diode, for breadboard or through-hole projects. Used with the LED Standoff and LED Light Shield to build the IR Transmitter Assembly (#350-00017). Frequently used with the IR Receiver for object detection and autonomous robot navigation, this is a compatible replacement wherever an Infrared LED is found in any of our Education Kits Components Listings.
-
product
Lamp gauge
E27
Shenzhen Chuangxin Instruments Co., Ltd.
To check the maximum dimensions of the screw thread and dimension T1 minimum of caps on finished lamps shown on sheet 7004-2.
-
product
Analog Platforms
(T1/E1/T3/E3/OC-3/OC-12/STM-1/STM-4)
Almost all T1 E1 T3 E3 Testers can be accommodated into rack-based units. Multiple rack units can be stacked together for greater scalability. Shown below is a rack based tProbe™ T1 E1 / T3 E3 Analyzer unit, and a Channelized T3 E3 Analyzer unit supporting 6 T3s (6 * 672 DS0s). Such customized rack serves the purpose of handling multiple communications lines and test complex functionalities.
-
product
WAN Tester II
The Telinc WAN Tester II is a sophisticated bit error rate tester in a compact, hand held package. It can test a wide variety of communications facilities and equipment including DDS, T-1, fractional T-1, E-1, fractional E-1, T-3 and E-3 NTUs, multiplexers, CSU/DSUs, T-1 CSUs, DTUsand TIUs. It includes a speaker to listen to voice in a DS0. It is supplied with changeable nickel metal hydride batteries and a built-in charger.
-
product
Non-Destructive Subsurface Layer Profiling
NMR-Mouse one-sided NMR
The unique, powerful Profile NMR-MOUSE® probe works hand-in-hand with the Kea2 spectrometer. The Profile NMR-MOUSE is a portable, open NMR sensor equipped with a novel permanent magnet geometry that generates a flat sensitive volume parallel to the scanner surface. The system can measure *Proton density as a function of depth *T2 NMR relaxation times *T1 NMR relaxation times *Self-Diffusion coefficient of liquids
-
product
PXI/PXIe Trigger Module
PXT1741
The PXT(e)1741 Trigger Module ist designed to build up a connection between trigger signals from any external trigger source (5V TTL Standard) and the PXI(e) trigger bus. Therefore the device is equipped with four SMA front connectors (T1 to T4).
-
product
T3/E3, OC3/OC12, & STM1/STM4 Testing
T3 E3 Analysis software compliments the hardware and supports simultaneously monitoring up to 12 x T3 E3 lines (2x Rack units) for all alarms, frame errors, signalling and data. If one adds the Channelized T1 Analyzer software to the system, then the T1s within the T3s can also be analysed in software, 12 x T3 E3 lines (=12*28 T1s) constituting 336 full duplex T1s, or 672 simplex T1s monitored simultaneously using a single Rack unit.
-
product
1000BASE-T1 SFP Module
Art.-Nr.: TE-1437
Convert between 1000BASE-T1 (automotive Gigabit Ethernet) and SGMII Interface. The 1000BASE-T1 SFP Module is the cutting-edge solution to convert between 1000BASE-T1 and SGMII. It fits into a standard Small Form-factor Pluggable (SFP) and generates 1000 Mbit/s full-duplex.
-
product
Dual Temperature
The Fieldpiece Dual-Temperature Accessory, model ATH4, measures two temperatures simultaneously using the included k-type, wrap tab beaded thermocouples. The technology inside the ATH4 provides superior temperature compensation in rapidly changing environments commonly found while performing field service. Use the ATH4 to find Delta T and just about any temperature split you want to measure. Displays T1, T2 and T1-T2 on your Fieldpiece meter, handle or data logger. It is included with the HVAC Guide® System Analyzer to get target superheat and for the Target Evaporator Exit Temperature test. Fieldpiece offers a wide variety of k-type thermocouples for various HVAC specific applications. Use pipe clamp T/Cs with the ATH4 to check for blocked filters.
-
product
100BASE-T1 MEDIACONVERTER NXP
Art.-Nr.: TE-1600
The ideal physical layer conversion between Automotive Ethernet and your PC system. The 100BASE-T1 MediaConverter NXP establishes one direct point-to-point conversion between automotive ECU’s using 100BASE-T1 and any standard Fast Ethernet device with RJ-45 connector.
-
product
2 Port T1/E1/PRI ISDN Simulator
SIM-2PRI
The most inexpensive ISDN simulator on the market. This unit has two PRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network.
-
product
Paper Softness Tester ZRD-T1
The ZRD-T1 Paper Softness Tester is a device designed to objectively measure the softness of paper products, such as tissues, toilet paper, or specialty papers. Softness is a complex tactile property influenced by factors like surface smoothness, flexibility, and bulk compressibility. It is widely used in industries such as tissue manufacturing, hygiene product development, textiles, and packaging to ensure compliance with quality standards and end-user comfort requirements. This test instrument conforms to many national and international standards: ASTM D2923: Standard Test Method for Rigidity of Paper – Measures bending resistance to determine stiffness. ASTM D6828: Standard Test Method for Stiffness of Nonwoven Fabrics – Evaluates drape and flexibility in materials like medical textiles or wipes. TAPPI T498: Bending Resistance of Paper (Gurley Method) – Quantifies resistance to bending forces, inversely related to softness. GB/T 8942: Chinese Standard for Softness Testing of Household Paper – Aligns with consumer expectations for tissue and toilet paper tactile quality. ISO 12625-9: Softness Evaluation of Tissue Products (optional add-on).
-
product
ISDN Chip Set
Emutel Symphony
Emutel Symphony is a convenient and flexible Basic Rate ISDN, Primary Rate ISDN and Analog PSTN network simulator. With support for S, U, E1, T1 and PSTN analog interfaces you can use the Emutel Symphony to test and develop a full range of ISDN(E1/T BRIS BRIU) and PSTN analog (FXS) equipment.
-
product
4 Port T1/E1/PRI ISDN Simulator
SIM-4PRI
The most inexpensive ISDN simulator on the market. This unit has four PRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network.
-
product
PXIe 10GBase-T1 Ethernet MEMS Fault Insertion Switch, 8 Channel
42-205-008
42-205-008 (PXIe) is a 8-channel fault insertion switches designed to simulate common faults on high speed two wire communication interfaces such as xBaseT1 Ethernet. They available with 4 or 8 channels of two wire serial connections and can be used for simulating faults on 10BaseT1, 100BaseT1, 1000BaseT1 and 10GBaseT1 Ethernet interfaces. Any wire can be set as open circuit and shorts can be applied across wire pairs. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to supply voltage or ground.
-
product
PXIe 10GBase-T1 Ethernet MEMS Fault Insertion Switch, 8 Channel
42-205-008
The 42-205-008 (PXIe) is an 8-channel fault insertion switch designed to simulate common faults on high speed two wire communication interfaces such as xBaseT1 Ethernet. It is available with 4 or 8 channels of two wire serial connections and can be used for simulating faults on 10BaseT1, 100BaseT1, 1000BaseT1 and 10GBaseT1 Ethernet interfaces. Any wire can be set as open circuit and shorts can be applied across wire pairs. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to supply voltage or ground.
-
product
Voice Monitoring
VOIP Echo
*The Voice Band Analyzer (VBA) is an analysis tool for monitoring the quality of voice band traffic (including hybrid echo) over VoIP, TDM and wireless networks*VBA works in conjunction with GL's TDM, Packet, and Wireless non-intrusive capture products, such as T1 and E1 Call Capture and Analysis, VoIP PacketScan&trade, and GSM, CDMA, and 3G Call Capture Products. VBA instantly detects voice file captures and with appropriately installed analysis modules, monitors speech levels, noise levels, and hybrid echo. Other analysis modules such as ITU-T P.561, P.562, P.563, fax and modem analysis, and many others can be hosted as plug-ins.*The VBA application can also operate on pre-captured files. It supports A-Law, µ-Law, 16-bit PCM (Intel), 16-bit PCM (Motorola) and MS Wave file formats.*Required software PKV100 and VBA032 at each probe location and PKV170 PacketScanWEB - Network Surveillance Software*Required hardware - 1U rack PC with sufficient hard disk for capturing over 10,000 calls (80 GB HD) for each VBA colocated with a probe*Additional hardware - PC for PKV100 PacketScan™ Software
-
product
WAN Simulator / Emulator
LANforge ICE
LANforge ICE emulates networks that involve limited bandwidth, latency, packet loss, and corruption. LANforge ICE tests the behaviour of devices that sit on either side of an impaired network. Reduces lab and training costs by replacing expensive WAN hardware, such as T1 and FrameRelay devices. Automates testing with various scripting features and libraries.
-
product
PXI/PXIe 1000Base-T1 Dual Multiplexer With Fault Insertion, Dual Channel
40-204-002
The 40-204-002 (PXI) and 42-204-002 (PXIe) are dual channel differential multiplexers designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They are available with support for 1 or 2-channels of two wire serial interfaces. Each channel pair can be looped out to external equipment or the switches can be used simulate a channel open fault. Using the fault bus, switches can simulate a short between both wires or a short to one of two externally applied fault conditions – such as battery supply or ground - via two fault buses.
-
product
PXI 10GBase-T1 Ethernet MEMS Fault Insertion Switch, 8 Channel
40-205-008
The 40-205-008 (PXI) is an 8-channel fault insertion switch designed to simulate common faults on high speed two wire communication interfaces such as xBaseT1 Ethernet. It is available with 4 or 8 channels of two wire serial connections and can be used for simulating faults on 10BaseT1, 100BaseT1, 1000BaseT1 and 10GBaseT1 Ethernet interfaces. Any wire can be set as open circuit and shorts can be applied across wire pairs. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to supply voltage or ground.
-
product
100BASE-T1 SPY 12 PORT
Art.-Nr.: TE-1500
Capture the traffic of 100BASE-T1, CAN/CANFD, LIN and Flexray Buses using only one device. The 100BASE-T1 SPY 12 port is a highly specialized test and evaluation tool for seamless capture of multiple in-vehicle-network technologies. It provides common timestamping of all incoming messages and delivers the traffic via Standard Gigabit Ethernet.
