LCR Meters
measure inductance(L), Capacitance, and Resistance or impedance.
See Also: Impedance Meters
-
Product
LCR Meters
-
GAOTek LCR meters are devices designed to measure the inductance (L), capacitance (C) and, resistance (R) of an electronic component. The LCR meters are measured in term of impedance but it can be converted through the instrument’s circuitry so the meter reads L, C and R directly with no human calculation required.
-
Product
LCR Meters
-
Sanwa Electric Instrument Co., Ltd
LCR meter is a type of electronic test equipment used to measure the inductance (L), capacitance (C), and resistance (R) of an electronic component. In the simpler versions of this instrument the impedance was measured internally and converted for display to the corresponding capacitance or inductance value.
-
Product
Chroma LCR Meters
-
Chroma Systems Solutions, Inc.
Some of the key features to look for in an LCR meter (also known as an impedance meter) are: accuracy, test frequency, measured parameters, test voltage and test current. Additionally, an easy to understand display of test results and the ability to access and use these results has become increasingly important. Component testing often requires much more than simply a resistance, capacitance or inductance value at a given test frequency and stimulus voltage. An LCR meter or impedance meter must have the flexibility to provide multi-parameters over wide frequency and voltage ranges.
-
Product
LCR Meters And Impedance Measurement Products
-
Complete impedance measurement solutions to meet your needs from LCR to impedance meters, plus test accessories for various R&D and manufacturing applications.
-
Product
Digital LCR Meters
-
Precision Mastech Enterprises Co.
Specialized, high-precision test instruments used to measure the inductance, capacitance, and resistance of electronic components by applying an AC signal to determine impedance, phase angle, and quality factors.
-
Product
High Frequency LCR Meters up to 30MHz
11050
-
Chroma Systems Solutions, Inc.
The Chroma 11050 Series HF LCR Meter is a precision test instrument designed to accurately measure and evaluate passive components at high speeds. Its measurement capabilities cover the primary and secondary parameters required for testing the inductance, capacitance, resistance, quality factor and loss factor of passive components. The HF LCR Meter has a broad testing frequency range 75kHz~30MHz/1kHz~10 MHz/60Hz~5MHz suitable for analyzing component characteristics under different frequencies. Its 0.1% basic measurement accuracy provides stable and highly reliable results. A fast 7ms measurement speed effectively increases productivity when working in an automated environment.
-
Product
LCR Meters/Capacitance Meters
-
Dual-band 1kHz/1MHz Capacitance Meter for High Speed Testing of Ceramic Capacitors on Production Lines
-
Product
LCR Meter 10Hz - 2 kHz High Precision
T3LCR1002
LCR Meter
LCR Meter 10Hz - 2 kHz High Precision.
-
Product
PathWave BenchVue LCR Meter Control App
BV0014B
-
Easily control your LCR meters with corrections, list sweeps, and more. Visualize results and create automated test for faster insights.
-
Product
LCR Meter
ET/QuadTech 1910/1920
-
The 1920 1 MHz LCR Meter is the most popular and designed to perform capacitance and impedance measurements on a variety of electronic components and materials over a frequency range from 20 Hz to 1 MHz. The1920 features programmable bias voltage from 1 mV to 2 V for biasing capacitors and other semiconductor devices during measurements.
-
Product
20000 Counts LCR Meter
LCR612 / LCR612R
-
Dual Displays provide quick tested results readouts,with L.C.R. Display values up to 19999 counts and Q.D.R. display values up to 9999 counts (Auto range). Basic accuracy: 0.5% for Resistance ;0.7% for Inductance, Capacitance
-
Product
LCR Meter
-
Precision Mastech Enterprises Co.
An electronic test device that measures Inductance (L), Capacitance (C), and Resistance (R) of components like capacitors, inductors, and resistors, often at various frequencies, to determine their actual values and parasitic characteristics beyond simple DC readings, essential for verifying component quality and suitability for circuits.
-
Product
High Precision LCR Meter
MCR-5000 series
-
MCR5000 series is a multifunctional LCR precision meter used for testing various electronic components. Adopt 4.3-inch TFT LCD display, simple display, elegant layout. It is a high speed, wide band, 5 bit test resolution impedance measuring instrument with 40hz-200khz multipie frequency points and 0.1% accuracy, which can meet the requirements of component parameter detection in various occasions. Is a high - quality cost-effective tester.
-
Product
LCR Meter 10Hz - 100 kHz High Precision
T3LCR1100
LCR Meter
LCR Meter 10Hz - 100 kHz High Precision.
-
Product
100 kHz LCR Meter
SR720
-
Stanford Research Systems, Inc.
The SR715 LCR Meter and SR720 LCR Meter measure passive components with as little as 0.05 % error. These easy-to-use instruments are quick to setup, adjust and calibrate.
-
Product
LCR Meter
-
*Rs, Rp, Cs, Cp, Ls, Lp, phase angle, Dissipation factor, Quality factor *Auto select series or parallel test mode *Auto select 100Hz/1kHz/10kHz test frequency, 0.5V rms approx. *Calibration
-
Product
Switch Modules - 16 Single Pole Relays Arranged as an 8x2 Matrix
JX16/AB-1
Switch Module
This module has 16 single pole relays arranged as an 8x2 matrix as shown in the figure to the left. The matrix may be operated and wired individually for up to 16 8x2's per chassis, or jumpered to the backplane to form up to a 128x2 matrix. It is available with Type S or M reed relays for high speed, long life application. These modules are usually used for 2 wire testing where high and low meter leads must be switched between any two points. Often used for 2 wire LCR meter measurements, cable testing, or open / short testing in a variety of applications.
-
Product
Short Termination, 4-Terminal Pair
42091A
Terminator
Use for performance tests of the 4-terminal pair LCR meters and impedance analyzers.
-
Product
LCR Meters
-
A type of electronic test equipment used to measure the inductance, capacitance, and resistance of an electronic component.
-
Product
LCZ LCR Meter
SS1062
-
This (SS1061 / SS1062 / SS1063) LCZ Meters are a test system for passive components designed for the use in electronic inspection or production process for quality control. They meet any demanding requirement on production speed and precision, discrimination of qualified products from unqualified ones, as well as internal setup, storing and calling function for up to 10 instrument groups, so they are actually optimum test instruments for component incoming and production inspection. Like as: transformer, inductor, resistor, capacitor, relay, motor, generator, eletric valve, contactor, cable, wire, etc..
-
Product
5MHz Bandwidth Precision
LCR01C
-
best handheld LCR Meter*Basic Accuracy: 0.2%*Test Voltage: 1Vrms*Circuit calibration:Open /Short
-
Product
LCR Meter
-
Delta United Instrument Co., Ltd.
Designed for measuring passive component attributes like inductance, capacitance, resistance, and impedance.
-
Product
Four Terminal Pair Standard Resistor Set
42030A
Programmable Resistor Module
The 42030A is a standard resistor set consisting of nine precision resistor standards which range from 1 mΩ to 100 kΩ. These resistors are primarily used for performance tests of Keysight's 4-terminal pair LCR meters and impedance analyzers. Refer to the instrument's operation/service manual for the method of using these standards.
-
Product
Precision LCR Meter, 20 Hz to 2 MHz
E4980A
LCR Meter
The E4980A precision LCR meter provides the best combination of accuracy, speed, and versatility for a wide range of component measurements. Offering fast measurement speed and outstanding performance at both low and high impedance ranges, the E4980A is the ultimate tool for general R&D and manufacturing test of components and materials. LAN, USB and GPIB PC connectivity enhances your design and test productivity.
-
Product
LCR & Component Tester
-
PeakTech Prüf- und Messtechnik GmbH
Digital LCR measuring device for resistance, capacitance and inductance with high-resolution dual multifunction display. Components can be measured in series or in parallel and the LCR meter also offers the choice between automatic and manual range selection.
-
Product
External DC Bias Adapter
16200B
-
The 16200B test fixture is designed to operate with high frequency LCR meters and impedance analyzers. It allows you to supply a bias current across the device of up to 5 Adc through a 7 mm port by using an external DC current source.
-
Product
10M/5M/1M/100K/10K/1KHz LCR meter
LCR01D
-
*Basic accuracy:0.3%*Test Voltage: 0.5Vrms* Circuit Calibration:Open/Short*Test Frequency:10MHz,5MHz,1MHz,100KHz,10KHz,1KHz*Measure Parameters Include:Z, Lp, Ls, Cp, Cs, ESR, D, Q, θ
-
-
Product
SMD Tweezer
U1782B
-
The Keysight U1782B is a tweezer to be used with the U1700 Series handheld capacitor and handheld LCR meters. For better noise immunity, the tweezer has a guard end to be connected to the meter´s guard terminal. The tweezer is now redesigned with a new shielded rigid cable to improve both usability and measurement stability.
-
Product
Standard Air Capacitor Set, 1pF To 1000pF
16380A
-
The 16380A is a standard capacitor set consisting of four precision capacitors - 1pF (16381A), 10pF (16382A) 100pF (16383A), 1000pF (16384A). These capacitors are primarily used for performance tests of Keysight's 4-terminal pair LCR meters and impedance analyzers. Refer to the instrument's operation/service manual for the method of using these standards.
