In-circuit Test Systems
See Also: In-circuit, Incircuit, In-Circuit Debuggers, In-circuit Emulators, In-circuit Probes, In-Circuit Test, In-circuit Testers
-
Product
Battery Test Systems
-
Was designed to meet the specific demands of our loyal customers. This system is used to test both single cell batteries as well as super-capacitors.
-
Product
ATE Test Systems
-
Introducing the Procyon ATE System! When it comes to ATE Test Systems for a for low- to high-volume production, Intepro has the testing power you require to be successful. For more than three decades, Intepro Systems has designed, built and integrated power supply test equipment for the world’s largest and smallest power supply manufacturers.
-
Product
High Speed Test Bench
AT444
-
AC motor with mechanical multiplying gearbox test benches allow precise programming of all drive parameters required for accurate rotating devices test.The use of special high-speed bearings, mechanical components and parts wear resistant leads to a large life. The supply includes the electronic drive and control as well as the entire oil cooling unit.
-
Product
Vibrator Test System
Sandwich Box Kit
-
"Gold standard” for vibrator tests provides more information than radio, wireline similarities or internal analysis. Other forms of vibrator QC use the vibrator controller accelerometers to measure vibrator motion. The Sandwich Box system includes external accelerometers which are used to independently record vibrator motion, thus providing a check of the whole vibrator system including the accelerometers.
-
Product
Test Systems
-
6TL’s speciality is simplifying the architecture of test systems, so that our customer’s Total Cost Of Ownership is drastically minimized. The technology that conveys our mission is called FastATE.FastATE technology is based on using intelligent modules to build test systems.
-
Product
Test System
Tessy
-
TESSY automates the whole unit test cycle including regression testing for your embedded software in C/C++ on different target systems. As an easy-to-install and easy to operate testing tool TESSY guides you through the unit test workflow from the project setup through the test design and execution to the result analysis and reporting. TESSY takes additionally care of the complete test organization as well as the test management, including requirements, coverage measurement, and traceability.
-
Product
Electronics Testing Solutions
-
Don’t cut corners when it comes to developing high-quality electronics functional testing solutions. Ball Systems helps you ensure you deliver the quality your customers expect by providing open and reliable advanced technical testing solutions.
-
Product
Optics Test Systems
Electronic And Visual Autocollimators
-
Optik Elektronik Gerätetechnik GmbH
OEG GmbH specializes in the use of autocollimators, collimators and telescopes for special applications in optical measurement technology in the wavelength range from 380nm to 1550nm (SWIR).
-
Product
Build-to-Print for Test Systems
-
Built-to-print / test system replication addresses your internal capacity and capability constraints. Ball Systems has perfected quoting, procurement, planning, assembly, testing, quality, delivery and installation to ensure your testers are on-time and on-budget, and meet design and production standards while keeping open and transparent communication.
-
Product
Servo-Pneumatic Asphalt Testing System
-
All signal conditioning, as well as high-speed data acquisition and control functions are done by the unit and graphically interfaced through CATS, windows based software running on a standard PC. The system is capable of performing the full spectrum of HMA tests: dynamic complex modulus, flow number, flow time, indirect tension, beam flexural fatigue and resilient modulus. These tests are done with the appropriate testing modules. The different testing modules can be obtained after the initial system acquisition at the same discounted price. In addition, guarantees system upgrades in order to meet future standards .
-
Product
PXIe Optical Test Modules
-
Coherent Solutions’ expanding portfolio of PXIe optical test modules bring a wide range of new mixed-signal test capabilities to the PXI platform. The new modules offer seamless integration with PXI Platform and deliver reliable and repeatable results across a wide range of optical and mixed-signal test applications.
-
Product
Battery Testing Systems
-
The CT2001 series Battery Testing Systems are designed for energy storage materials research and battery test. The eight channels are independently programmed and controlled by the computer. The Current ranges are from 1 mA to 5 A and Voltage ranges from 2V to 15V. Each testing system is specifically built for customer needs.
-
Product
Optics Test Systems
F Number Meter
-
Optik Elektronik Gerätetechnik GmbH
The f-number of a camera lens is defined as the quotient of the focal length f' and the diameter of the entrance pupil. The f-number measuring device is a simple structure for the automatic, software-controlled measurement of the f-number of optical systems.
-
Product
High Node Count In-Circuit Test Fixtures
HNC Test Fixture
-
Circuit Check continues to be a leading edge provider of custom engineered test solutions with our new Keysight i3070 HNC test fixture. Working with Keysight Technologies during the development of their HNC adapter in 2011, we were the first test fixture provider to offer customers with a solution to test large node count boards. High node count test fixtures can handle greater than 10,000 probes.
-
Product
Gel Strength Test System
LD-LGST-A10
-
Gel Strength Test SystemLD-LGST-A10is mainly used to measure the gel strength of gelatine under the stipulated environment. It has traveling accuracy ± 0.3 % and Test range up to 5 to 1000 g Bloom. It consists of Jelly Strength Tester, Constant Temperature Bath and Refrigerator. Sampling depth can be present arbitrarily in 1 to 60 mm. It consists four kinds of sampling measurement modes: single-step, maintaining, circulating and automatic.
-
Product
Handover Test Systems
-
Family of handover test systems designed for handset-to-network handover testing. Internal step attenuators allow the RF signal between the network access points and the handsets to be dynamically faded up/down. The Ethernet/Serial models run our latest generation 3.x.x firmware that features easy to use ASCII formatted commands.
-
Product
RSE Wireless EMC Spurious Emission
TS8996
-
The R&S®TS8996 RSE test system is designed for EMI and radiated spurious emission testing on wireless devices in semi-anechoic or fully anechoic chambers. The modular design makes it easy to extend the system to include new communications technologies. Typical devices under test include mobile phones or radio sets along with radiated measurements of other short-range devices. Standards require a wide range of test setups and a wide and high frequency range (up to 40 GHz). ESW or FSW frequency ranges are extended up to 325 GHz with option B21 using receive units TC-RSE for 5G FR2. Dedicated RSE test routines are also covered for this frequency range.
-
Product
Test System for Circuit Breakers
-
Spitzenberger & Spies GmbH & Co. KG
Thermal testing with long-time currents up to 550 A. Magnetic testing with short-time currents up to 2000 A. Control software. Customer specifically adapted. 4 candidate records with pneumatic adapting.
-
Product
Manual Test System for ICT & ISP with Integrated ABex and up to 426 Test Points
LEON Fixture
-
The LEONFixture is the ideal ICT and ISP solution for small and cost sensitive applications. This manually operated test system combines optimal ergonomics with high performance, durability and precision, ensuring your investment over the long term. The LEONFixture features a test system integrated in a manual base fixture. The system is designed to be used with an Ingun ATS MA13 insert which could be customized by a lot of fixture houses all over the world.As part of the LEON Family, LEONFixture is based on the ABex platform which directly incorporates Konrad analog bus technology and PXI/PXIe in one chassis.
-
Product
Motorized Force Test System
MT Series
-
In the past, film extruders, paper producers, converters, and woven/non-woven fabric producers have had the choice of test stands and universal test machines which are either value-priced peak-force-only machines, or expensive computer-operated integral-load cell machines. Now you can have the best of both worlds in a single instrument. The series MT-1500, a simple to use computer operated tester, with Quality Control software for automatic calculation and graphical display of break, elongation, yield, modulus, and other, tension and compression force information.
-
Product
Mezzanine System
3564
-
The 3564 is a four channel comparator board with a common mode range of -150V to 150V on the two differential inputs and a DAC per channel to set trigger levels. The high common mode range and DC coupling provides a robust solution to level detection and triggering.
-
Product
ESD & Latch-Up Test System
-
Identify and help correct ESD and latch-up susceptibility issues on sensitive integrated circuit components prior to full-scale production with the Thermo Scientific™ MK.2-SE ESD and Latch-Up Test System. The MK.2-SE test system provides advanced capabilities to test high pin count IC devices to Human Body Model (HBM) and Machine Model (MM) ESD standards. The system’s pulse delivery design addresses wave form hazards such as trailing pulse and pre-discharge voltage rise, and performs Latch-Up testing per the JEDEC EIA/JESD 78 Method.
-
Product
Electronic Transformer Test System
UI2000-ET
-
• Input characteristics analysis 1) Measure Vrms (10-300V) Lrms (0.04-4A) W, PF, Hz, total harmonic and 0-50 component of harmonic 2) Accuracy: ± (0.4%reading + 0.1%range + 1digit) • Output characteristics analysis 1) Measure lamp voltage (1-60V) lamp current (03-20A) lamp power, crest factor and oscillatory frequency 2) Accuracy: Class 2 • It can print without compute, and provide the communication port for PC
-
Product
SR/QE Testing System
PVE300
-
Industrial Vision Technology Pte Ltd.
Solar Cell Multi-function SR/QE Testing System is specially designed for Photovoltaic Industry to characterize the Optical Performance of Raw material, process wafer, finished solar cell, as well as small Module.
-
Product
Electrolyzer Test Systems
-
Advanced Test System for Research & Development of PEM Electrolyzers
-
Product
Lightwave Test Systems
-
Keysight offers a wide range of innovative test-and-measurement solutions to accelerate the progress of next-generation high-bandwidth optical networks. Keysight's mission in the optical market is to shorten time to market and reduce cost of test for customers in R&D and manufacturing. In addition, Keysight enables new technologies that include 40 Gb/s optical components, network elements and systems, and all-optical fiber networks.
-
Product
Battery Test System
WBCS3000Ls / WBCS3000Le
-
Low current model8 channel battery cycler (expandable up to 128 channels)max. voltage range : ±5Vmax. current range : - Model WBCS3000Ls : ±10mA - Model WBCS3000Le : ±100mACustomized specification is available.
-
Product
Integrated I-V Test Systems
-
The OAI Integrated I-V Test System is perfect for R&D as well as production, the OAI Integrated I-V Test System delivers extremely accurate solar cell performance measurement. OAI’s advanced fully Integrated I-V Test System is designed to overcome the limitations of flash testing by providing a highly optimized pulse width and voltage sweep rate to match any type of solar cell’s high capacitance and slow dielectric response speed. As a result, the system produces extremely accurate measurements of solar cell I-V parameters and efficiency while leading to the most accurate test results.
-
Product
In-Circuit Testing and Test Engineering
Teradyne Z1890
-
2048 Pure Pin Test Nodes3 & 6-wire Analog MeasurementsVector Test for VLSI, PLCC’s & ASICSMultiscan II Vectorless TestingIEEE Functional Interface BoardLarge Custom Vector Library
-
Product
Vibration Test Systems
G-9 Series
-
The G-9 Series Vibration Test Systems, featured by high eccentric moment and a large loading table supported by the unique rigid lateral suspension structure, are suited to transportation tests for relatively large specimens; packaged goods and electric apparatus. In addition, the unique structure enables horizontal tests of relatively heavy specimens without conventional horizontal slip tables.
