PCI Carrier
PCI card facilitating the integration of other bus type cards.
-
Product
Dual Port Simulator Fiber Channel PCI Module
PCI-FC4 Simulyzer
Simulator
The modules are available as a single-function board - for analysis or for simulation / data generation - but also as a full-function board for simultaneous analysis and simulation. By simply upgrading the firmware / software, a single function board can become a full function board without having to purchase new hardware.
-
Product
PCI Resistor Card 2-Channel 2 Ohm To 65.5k Ohm With SPDT
50-293-133
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCIe and PCI Avionics Interface Cards
Interface
Ballard PCI Express (PCIe) and PCI Avionics Interface Cards enable computers to interface with a variety of avionics databuses for testing, validating and simulating commercial and military avionics equipment and systems.
-
Product
14-Bit, 32-Ch Isolated Analog Output Universal PCI Card
PCI-1724U
-
32 high-density analog output channelsFlexible Output Range: +/-10 V, 0 ~ 20 mA and 4 ~ 20 mASynchronized output functionKeeps output values after system hot resetBoardID™ switch
-
Product
PCI Express Card with 96 DIO and Counter/Timers
PCIe-DIO-96C3
-
This is a x1 lane PCIe, 96 line digital input/output card with counter/timer capabilities designed for use in high I/O density application requirements. I/O connections are made via four 50-pin header connectors. The card is 12.25 inches long (312 mm) and may be installed in any full-length slot that has x1 lane PCIe.
-
Product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 1.02k Ohm
50-294-021
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI Precision Resistor Card 3-Channel, 3Ω To 22.3MΩ
50-297-154
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI High Density Pecision Resistor Card, 3-Channel, 3.5Ω To 395kΩ
50-298-142
Programmable Resistor Module
The 50-298-142 is a high density programmable resistor card with 3 channels which can be set between 3.5Ω and 395kΩ with 0.5Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI 48 Channel TTL Digital Interface
8005
-
The 8005 digital I/O interface provides 48 channels of buffered drive digital I/O emulating 8255 mode zero, which can be utilized for PC based control and automation of equipment including sensors, switches, security control systems, and other industrial automation systems. 10K pull-up resistors are included. Optional values are available.
-
Product
8-CH Relay Outputs & 8-CH Isolated DI PCI Cards
PCI-7250/7251
Relay
ADLINK's PCI-7250/7251 provide 4-CH SPDT (Form C) & 4-CH SPST (Form A) relay outputs and 8-CH isolated digital inputs. The status of each relay output is represented by an onboard LED. When the relay is in SET condition, its corresponding LED will turn ON, and on the contrary, it is OFF. All digital input channels are nonpolarity, optically isolated, and may be set to use RC filter or not. The devices are suitable for collecting digital inputs in noisy environments. The PCI-7251 is an 8-CH relay outputs and 8-CH isolated DI extension card of the PCI-7250. All the I/O functions of PCI-7251 are the same as those of the PCI-7250. The PCI-7251 has to be connected with PCI-7250 and the bus interface is controlled by the PCI-7250. Up to three PCI-7251 cards can be connected to one PCI-7250, therefore, expanding the PCI-7250's DIO from 8 DIO to maximum 32 DIO.
-
Product
SATA Drive Carrier
SD1-DISCO
-
The SD1-DISCO is a peripheral slot card for CompactPCI® Serial systems. The board accommodates a 2.5-inch size SATA drive, controlled by the SATA channel derived from the backplane connector P1.
-
Product
PCI Express 5.0 Transmitter Electrical Performance Validation and Compliance Software
D9050PCIC
-
Use the PCIe 5.0 Tx compliance software to test, debug and characterize your PCIe Gen5 designs quickly and easily. It automatically configures the oscilloscope for each test and generates an informative HTML report upon test completion. The application compares the results with the specification test limit and includes margin analysis which indicates how closely the device passes or fails each test. With the option InfiniiSim Waveform Transformation Toolset, the software supports integrated de-embedding of the breakout channel of the test fixture.
-
Product
PCI Precision Resistor Card 3-Channel, 3Ω To 11.4MΩ
50-297-153
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI High Density Pecision Resistor Card, 6-Channel, 3.5Ω To 102kΩ
50-298-040
Programmable Resistor Module
The 50-298-040 is a high density programmable resistor card with 6 channels which can be set between 3.5Ω and 102kΩ with 0.125Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Low Profile PCI Express 4-Port
7402e
-
The 7402e low profile PCI Express serial interface provides four serial ports, each individually field-configurable for RS-422 or RS-485 communications. The board uses a 16C954 UART with 128-byte Tx/Rx FIFOs that enables data rates to 921.6K bps for reliable high-speed communications in data intensive applications. This high-performance UART includes 9-bit framing support and is register compatible with legacy 16550 software applications. In addition, the board derives a 62.5 MHz clock from the PCI Express link. This ultra-high speed clock is divided by a flexible 8-bit clock prescalar with 1/8 steps to provide support for the widest range of standard and non-standard baud rates.
-
Product
PCI Express Cable Extender
SKU-016-XX
-
The PCI Express Cable Extender was designed to support the development and debugging of PCI Express boards. The PCI Express Cable Extender allows easy access from both sides of the PCI Express board that are plugged into the Extender. It has overcurrent protection and provides access to the PCI Express bus JTAG signals. By enabling access to the PCI Express bus JTAG signals, the PCI Express Cable Extender becomes a universal device that helps support the programming/loading of FPGA/CPLD during debugging and the verification PCI Express boards.
-
Product
PCI Express 6 Base Specification Receiver Test Automation
N5991PB6A
-
The N5991PB6A is the receiver test automation software for bit error ratio testers, allowing you to test and characterize PCI Express 6.0 ASICs
-
Product
33 lane, 9 port, PCI Express
PEX 9733
-
Broadcom has extended the reach of PCIe for use as a fabric for data center and cloud computing through its ExpressFabric initiative and platform of hardware and software. ExpressFabric can eliminate expensive bridging devices within the rack, such as adapter cards that translate native PCIe to Ethernet and back to PCIe. Yet ExpressFabric works seamlessly with other standards used within the rack and in rack-to-rack connectivity.
-
Product
Osprey PCI Unibus Adapter
9793
-
Dual-height card plugs into PDP-11 Unibus backplane. Fibrechannel cable plugs into Unibus logic connector on Osprey /TXP I/O Adapter logic provides Programmed I/O and DMA access to "real" Unibus compatible controllers (those not otherwise emulated).
-
Product
PCI Strain Gauge Simulator Card, 2-Channel, 2k
50-265-302
Strain Gauge Simulator
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
cPCI IP Carrier Module With Front And Rear I/O
DP-cPCI-5211
-
DP-cPCI-5211 IP carrier board provides electrical and mechanical interface for four industry standard IP modules. The board provides full data access to the IP modules I/O, ID and memory spaces. The programmable registers are used for configuring and controlling the operation of IP modules.
-
Product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 510 Ohm - SPST
50-294-114
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Low Profile PCI 8 Reed Relay Output
8012
-
The 8012 Low Profile PCI digital interface provides eight Reed relay outputs (SPST) and eight optically isolated inputs. Reed relays are well suited for low current applications. The relays are normally open, and close when energized. The board is MD1 Low Profile and Universal Bus (3.3V and 5V) compatible.
-
Product
PCI Express Digital I/O Card With Counters And IRQ
PCIe-DIO-24HC
-
This product is a x1 lane PCIe DIO board with basic DIO, Counter/Timers and interrupt generation capabilities. The card uses an 8255 compatible chip, providing 24 DIO lines. The DIO lines are grouped into three 8-bit ports: A, B, and C. Each 8-bit port is configured via software to function as either inputs or outputs. Port C is further broken into two 4-bit nybbles via software, configured as either inputs or outputs.
-
Product
PCI Express Optical Link Board
SIS1100-E2
-
The SIS1100-e2 is the follow up card to our SIS1100-eCMC board (without CMC carrier functionality). It was developed to extend the lify cycle of our PCIe to VME interface. For software/driver compatibility reasons we still employ the PEX8311 PCI Express to local bus bridge chip.
-
Product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 16.3k Ohm
50-294-031
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
6U Dual 64/100 PMC VME Carrier
V2PMC2
-
The V2PMC2 PCI-X/PMC carrier card is a 6U VME that holds up to two single-width or one double-width PCI-X/PMC modules. The V2PMC2 works in association with a PCI-Express host which is connected to it through a x4 PCI-Express serial link onto P0 connector.
-
Product
1 MS/s, 12-Bit, 16-Ch Multifunction PCI Card
PCI-1712
-
16 single-ended or 8 differential or a combination of analog inputs12-bit A/D converter, with up to 1 MHz sampling rateTwo 12-bit analog output channels with continuous waveform output function16-ch digital input and 16-ch digital outputThree 16-bit programmable multifunction counter/timers on 10 MHzProgrammable gainAutomatic channel/gain scanningOnboard FIFO memory (AI: 1,024 samples AO: 32,768 samples)Auto-calibration (AI/AO)PCI-Bus for data transferPre-, post-, about- and delay-trigger data acquisition modes for analog input channelsFlexible triggering and clocking capabilities
-
Product
Carrier Card
SPR518
-
The SPR518 provides a smart upgrade path to affordably replace the existing SPR418A PCI Express (PCIe®) carrier for XMC modules. The new card provides for unimpeded data transfers within traditional PCs, at the full rate supported by the mezzanine card.
-
Product
2-Port PCI Express 10 GigE Vision Frame Grabber
PCIE-1182
Frame Grabber
Intel server-grade E610-XAT2 10 GbE MAC+PHY ControllerSupports Jumbo frame (9500 byte) and link aggregationPCI Express 4.0 x4 compliant, provide a low‑profile version (half‑length, half‑height) to offer greater flexibility for users’ applicationsPoE+ compliant to support up to 30W power output with recoverable eFuse
