PXI Carriers
-
Product
PXI 4-Slot BRIC Matrix, 22x16 1-Pole (2 Sub-cards)
40-562B-021-22X16
Matrix Switch Module
The 40-562B-021-22X16 is a high density BRIC4 matrix module with a size of 22x16 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI Breadboard Module, 2-Slot, 25-Pin D-Type
40-220A-302
Signal Module
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
Product
Astronics PXIe-1209 , 2-Channel, 100 MHz PXI Pulse Generator
785033-01
Pulse Generator
2-Channel, 100 MHz PXI Pulse Generator - The Astronics PXIe-1209 provides dual independent pulse generation with full control of all timing parameters with extremely high resolution. Both channels are fully independent, and you can configure pulse delay, double pulse spacing, pulse width, and period. Each channel offers front panel trigger inputs with software-programmable thresholds and PXI backplane triggering.
-
Product
Fixed Wavelength CW Laser Source (FP) - PXI
Laser 1100 Series
Laser Source
The Laser-1102 is a Continuous Wave (CW) laser source offering high power 850 nm output into multimode fiber with stable output power operation.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-044-HI
Programmable Resistor Module
The 40-230-044-HI (PXI) and 42-230-044-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4Ω and 1.5MΩ with 2Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI 8 Slot BRIC 45x16 2-pole (3 sub-cards)
40-561A-122-45X16
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 12-Slot BRIC Matrix, 924x6 1-Pole (11 Sub-cards)
40-558-121-924X6
Matrix Switch Module
The 40-558-121-924x6 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
PXIe-1066DC, 18-Slot, DC Power Supply PXI Chassis
781812-01
Chassis
PXIe, 18-Slot, DC Power Supply PXI Chassis—The PXIe‑1066DC adds high-availability features to the PXI Express platform to maximize system uptime. Built on the PXIe‑1065 backplane architecture, the PXIe‑1066DC incorporates hot-swappable, redundant DC power supplies as well as hot-swappable, front-accessible, redundant cooling fans. These high-availability features improve the mean time between failure (MTBF) and mean time to repair (MTTR) of the PXI system.
-
Product
PXI High Density MUX BRIC, 4-Chan, 40-Pole
40-570-211
Multiplexer Module
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
PXI 2.5W Programmable Resistor Module, 4-Channel, 1Ω to 62.1Ω
40-251-111
Programmable Resistor Module
The 40-251-111 is a programmable resistor module with 4 channels which can be set between 1Ω and 62.1Ω with 0.25Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
Product
PXI 8 Slot BRIC 161x16 1-Pole (7 sub-cards)
40-560A-121-161X16
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-354-HI
Programmable Resistor Module
The 40-230-354-HI (PXI) and 42-230-354-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4.5Ω and 22.05MΩ with 2Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXIe-5774 , 12-Bit, 6.4 GS/s, DC-Coupled, 2-Channel PXI FlexRIO Digitizer
785646-02
FlexRio Digitizer
The PXIe-5774 provides up to 3 GHz of DC-coupled analog bandwidth and 12 bits of resolution. You can operate the PXIe-5774 in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. The voltage ranges are software-selectable and include 200 mV peak-to-peak and 1 V peak-to-peak, with a selectable DC offset. The PXIe-5774 is ideal for time-domain measurements in areas such as scientific instrumentation, medical imaging, and particle physics. The FlexRIO driver includes support for finite acquisition, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA.
-
Product
PXI Monitored Multiplexer, Quad 16-Channel, 1-Pole
40-619-004
Multiplexer Module
The 40-619-004 is a high density PXI 2 A multiplexer module in quad 16-channel configuration using high quality electro-mechanical signal relays allowing each channel to switch current up to 2 A and voltage up to 250 VAC/DC.
-
Product
PXI-8517, 2-Port PXI FlexRay Interface Module
780689-02
FlexRay Interface
2-Port PXI FlexRay Interface Module—The PXI‑8517 is designed for developing FlexRay applications. As part of the NI‑XNET platform, the PXI‑8517 works well in applications requiring real-time, high-speed manipulation of hundreds of FlexRay frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The PXI‑8517 contains two fully functional FlexRay interfaces, allowing an individual ECU to be connected to the interface when other cold-start nodes are not available. You also can use the interfaces individually to connect two separate FlexRay networks while maintaining full performance on each interface.
-
Product
PXI 24 Channel High Voltage Multiplexer
40-320-101
Multiplexer Module
The 40-310/320 Range of High Voltage Switching Modules will hot switch up to 750V peak and cold switch up to 1000V peak in either general purpose relay (40-310) or multiplexer (40-320) configurations. These modules contain high-quality reed relays with switching ratings comfortably higher than the 40-310/320 specification. Applications for the 40-310/320 series modules include; circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing.
-
Product
PXI 8-Slot BRIC Matrix, 44x16 1-Pole (4 sub-cards)
40-562B-121-44X16
Matrix Switch Module
The 40-562B-121-44X16 is a high density BRIC8 matrix module with a size of 44x16 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI Prototyping Module, 2-Slot, 9-Pin D-Type
40-225A-702
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
PXI 2.5W Programmable Resistor Module, 4-Channel, 1.5Ω to 472Ω
40-251-020
Programmable Resistor Module
The 40-251-020 is a programmable resistor module with 4 channels which can be set between 1.5Ω and 472Ω with 0.125Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI Single 16 Channel Switch Simulator
40-485-221
Switch Module
Designed to simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. It allows automotive I/O devices to be tested for correct operation under adverse conditions.
-
Product
PCI Express FMC Carrier
RFM-BSC5GT7H1
-
Sundance Multiprocessor Technology Ltd.
The RFM-BSC5GT7H1 is a PCI Express short sized FMC carrier board with Cyclon V FPGA (Altera), which is designed mostly for low cost, high-performance data acquisition.
-
Product
PXI Source/Measure Unit
-
Keysight PXI source/measure unit (SMU) offers high-throughput and measurement quality for design validation and production test of RF power amplifiers. It delivers industry-leading output stability under extreme, dynamic load conditions and unmatched transient performance to dramatically reduce voltage droop due to pulse loading for faster test time.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-152-HI
Programmable Resistor Module
The 40-230-152-HI (PXI) and 42-230-152-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4.5Ω and 5.762MΩ with 0.5Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI Solid State Switch Module, 6xSPST, 30 A
40-183B-011
Switch Module
The 40-183B-011 has 6 high current SPST switches in two PXI chassis slots. Each SPST switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each SPST switch can support 30A of continuous current and switch up to 40V signals. The switch can sustain inrush currents in excess of 120A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
PXI 32 Channel I/O, High Side Driver
40-413-001
Digital I/O
A 32 channel Digital I/O module with high output voltage and currentcapability and a dual variable threshold input. The 40-413 range is available in three configurations, a high side only (shown here), alow side only and a combined high and low side each capable of driving 2A loads. Eachoutput is fully protected against over-voltage, over-current and thermal overload,ensuring robust and reliable operation in the toughest test environments. For highside voltage driving the high side voltage source is supplied from an external voltagesource, permitting the module to drive high capacity loads without impacting thePXI chassis power supply.
-
Product
PXI 3A Power MUX BRIC, 24-Channel, 6-Pole
40-571-403
Multiplexer Module
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
PXI 8 Slot BRIC 60x32 1-Pole (12 sub-cards)
40-562A-121-60X32
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 8 Slot BRIC 64x12 2A 1-Pole Matrix
40-597-102
Matrix Switch Module
The 40-597 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 100VDC/70VAC. The 40-597 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
PXI 8-Slot BRIC Matrix, 528x4 2-Pole (12 sub-cards)
40-562B-122-528X4
Matrix Switch Module
The 40-562B-122-528X4 is a high density BRIC8 matrix module with a size of 528x4 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI 4-slot BRIC Matrix, 64x16, 1 pole (2 Sub-cards)
40-558-401-64x16
Matrix Switch Module
The 40-558-401-64x16 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
