Comparators
Contrast similar or divergent values.
-
Product
PXI/PXIe High Density Digital Input Module, 128-Channel, 50V
42-414-101
Digital Input Module
The 40-414-101 (PXI) and 42-414-101 (PXIe) are 128-channel digital input modules with 50 V inputs and provide a convenientway of determining the status of input lines by comparing the input voltage with two threshold voltages - quicklyestablishing if the input is low, high or in an intermediate logic state.
-
Product
Cable Testers
CableJoG 64
-
CableJoG 64 can test up to 64 individual connections of all manufacturers of connectors. This simple test instrument stores up to 55 separate connection configurations. Each cable that is tested is compared with the configuration stored in the cable testers memory to produce a pass/fail indication of each pin connection.
-
Product
Electric Insulation Oil Automatic Measurement System
DAC-5016
-
DAC-5016 is an automatic test system of insulation oils according to JIS C-2101.The system automatically enables changing over samples (liquid cells) up to max 8 pieces and testing the dielectric loss tangents and the volume resistivities.In automatic mode, the dielectric loss tangents and the volume resistivities are automatically measured, and then the results are printed out with the built-in printer. And the relative permittivities and the volume resistivities calculated are also printed out. Therefore the test time is greatly saved compared to the conventional test methods.
-
Product
Pressure Generators
-
Calibration hand pumps serve as pressure generators for the testing, adjustment and calibration of mechanical and electronic pressure measuring instruments through comparative measurements. These hand pump calibrators can take place in the laboratory or workshop, or on site at the measuring point.
-
Product
Goniophotometer
-
A goniophotometer is a system to measure the luminous intensity of the source (or illuminance from the source at a given distance) in many different directions from the source. Compared with the sphere method, the goniophotometer method is theoretically free from errors due to differences in intensity distribution of the light source under test. It is applicable to acquire the luminous intensity distribution, luminous flux, spatial color distribution, and luminance distribution of lamps and luminaires.
-
Product
Flash Vs. Scan
-
A LiDAR system can observe the complete field of view (FOV) at once, called Flash systems. Flash typically works well for short to mid-range (0-100m), and by capturing the complete scene at once also objects with high relative speeds can be detected properly. Another implementation is to focus on a subset of the FOV, consequentially look at the next subsets, until the complete FOV is covered, called Scanning. Scanning can focus the light on the subset instead of the full FOV, and therefore can do object detection at a longer range compared to Flash.
-
Product
Resistance Software
OhmRef
-
OhmRef provides the power of automation for Standards maintaining statistical control of resistance values in your laboratory. This program controls a Low Thermal Scanner along with other equipment commonly available in Standards Laboratories to compare resistance standards over the range of 100µΩ to 10GΩ . Comparison accuracies arebetter than 1 ppm in the midranges.
-
Product
Scanning Electron Microscope
E5620
-
The E5620 is a MASK DR-SEM(∗) product for reviewing and classifying ultra-small defects in photomasks and mask blanks. It implements Advantest’s highly stable image capture technology to easily import defect location data from mask inspection systems and automatically image the locations. Compared to the E5610, our predecessor DR-SEM system, the E5620 features a number of improvements designed specifically to target mask requirements for extreme ultraviolet (EUV) lithography.
-
Product
Linear Array
-
Linear array sensors consist of a linear array of integrating photosensing pixels which measure incident light over a user-defined exposure time and generate a voltage or digital output which represents the light exposure at each pixel. The sensors are available in a variety of lengths and pixel resolutions. The analog output may be directly interfaced to an ADC for digital processing or for comparing black/white thresholds. Applications include contact image sensing, optical character recognition, edge detection, and object measurement in products such as copiers, document scanners and spectroscopy.
-
Product
Agriculture Solutions
-
The trend in agriculture: The drives of machines and commercial vehicles must be capable of transmitting increasingly high power within a limited space. Reproducible quality in series manufacture with the shortest possible production times are the key requirements in this industry.The hay makers and harvesters perform their task using straight bevel gears. Because the loads in these machines are comparatively small, a cost-effective manufacturing solution is crucial for the market success of straight bevel gears. It’s a different story as far as tractors are concerned: Spiral bevel gears are installed in the rear axles in this case – and the bevel gear set of a tractor’s rear-axle differential must transmit up to 400 kW. In tractors, cylindrical and planetary gears are also used in manual transmissions and counter shaft transmissions as well as planetary gear drives for transmitting power to the enormous drive wheels. These cylindrical and planetary gears must be efficient, quiet-running, and low-maintenance. With solutions from Klingelnberg, the entire portfolio can be produced on bevel-gear and cylindrical-gear machines.
-
Product
Calibration Equipment
-
Calibration is the method of comparing tools and measuring devices to higher accuracy standards. Torque calibration equipment is the official means by which torque testers and sensors are calibrated and are traceable to National or International Standards, such as N.I.S.T and ISO. In order to maintain precision accuracy, it is essential that torque measuring equipment be calibrated regularly. By equipping your team with Mountz calibration equipment, you can avoid the costly chore of sending your torque tools to the lab whenever they fall out of alignment.
-
Product
Mini Digital Output Pressure Sensors
DLV Series
-
The DLV Series Mini Digital Output Pressure Sensor is based on the already popular DLVR series pressure sensors. This series offers excellent perfromance over middle pressure ranges of 5 PSI to 60 PSI compared to the DLVR low pressure range products.
-
Product
Partial Discharge Inductor
Tracy
-
Cable testing and diagnostics with the BAUR tracy. The BAUR tracy partial discharge inductor induces a signal at the apparent fault location in the cable from outside. In combination with any PD measurement system, e.g., PHG TD/PD, the induced signal can be located and compared with the result of the partial discharge pre-location. The partial discharge location can thus be determined precisely.* Portable, battery-operated signal coupling device* Suitable for cables and cable accessories* Inductive signal coupling* Aviods costly, unnecessary replacements of PD-free cable accessories
-
Product
Sawmill Green Lumber Sorting System
-
The transverse sawmill meter sorts pieces into four moisture groups with similar drying characteristics by assigning a dry-ability index number. This critical first step in end-to-end moisture control improves kiln performance by reducing aggregate standard deviation and total drying time when compared to unsorted loads.
-
Product
Megohmmeter
1863
-
The GenRad 1863 Megohmmeter is the choice for production and inspection tests on devices with resistances up to 20 Tohms. The GenRad 1863 will measure resistance at any of five test voltages of: 50V, 100V, 200V, 250V, and 500 VDC. Compared to the GenRad 1864, which has adjustable test voltages from 10V to 1090V, this unit has fewer controls, and is the more economical of the two models.
-
Product
1149.6 Boundary Scan Feature, GTE 10.00p
K8213B
-
Keysight’s Interconnect Plus Boundary Scan 1149.6 feature enables all the tools required to develop and execute this test method on the board under test. Compared to the 1149.1 standards, the 1149.6 standards define test methods for the boundary scan devices that are designed with AC coupled signals or differential nets needed for high-speed operations of the device.
-
Product
Renishaw Styli
-
Advanced Industrial Measurement Systems
Renishaw’s styli are some of the most accurate in the market. The balls on the end of the styli are bonded to the stems to ensure that there is no wiggle room – as compared to the traditional ball drilling method to fix the stem to the ball – which causes distortions, and thus measurement errors. Renishaw’s styli are a much more capable option for the CMM. These balls also perfectly spherical, are located at the optimum position on the stem, are threaded nicely and are extremely sturdy during measurement. Additionally, Revolution® CMM’s are supplied with Renishaw Grade 5 High Accuracy Styli.
-
Product
Micropower Voltage References
-
Analog Devices offers a broad line precision micropower voltage references with extremely low quiescent currents (series references) or minimum shunt currents (shunt voltage references). All of our precision voltage references offer excellent initial accuracy and low temperature drift over time and temperature. Our Reference Plus products combine precision voltage references with comparators or amplifiers.
-
Product
ElcoMaster Oven Profiling Software
-
*Oven Logger set up & programming*Paint/Powder parameter library*Product probe maps*Fully customisable inspection templates*Selectable probe/channel traces*Statistical analysis by probe/channel*Max, Min, standard deviation, coefficient of variation*Temperature profile, cure progress, histogram & individual cure value graphs against product*Time at temperature, time of peak difference*Time above maximum absolute & minimum cross link temperatures*Fully customisable inspection reports*Combined reports - coating thickness, gloss, adhesion, profile, climate, surface cleanliness*Report generator wizard & PDF generator*Email or export data*Import photo’s, data sheets, critical data, inspection notes, etc & include on inspection reports*Cloud computing - allows for cross site collaboration, including internal text messaging tool*Overlay temperature profiles, review and compare multiple oven profiles over time*Use additional data loggers for multiple channels or run overlays
-
Product
Thermistor Power Meter
N432A
-
Keysight N432A is the replacement for Keysight's legacy 432A analog thermistor power meter. The single-channel, average RF power meter operates with the Keysight 8478B and 478A thermistor mounts. The N432A-and-thermistor-mount pair is ideal for applications that require high measurement accuracy, particularly in metrology and calibration laboratory environments. The enhanced thermistor power meter comes with a digital color LCD display, and user-friendly front panel interface. Its built-in calibration factor table provides a more convenient and accurate method of storing calibration factors as compared to the old knob-turning approach of the 432A. The N432A is LXI compliant, and programmable via GPIB, USB and LAN.
-
Product
Desktop Inspection/Measurement Systems VisionGauge Digital Optical Comparators
400 Series
-
The 400 Series VisionGauge Digital Optical Comparator are state-of-the-art inspection and measurement systems in a compact desktop format. It''''''''s a compact desktop system that still provides a large working envelope. The 400 Series is a very cost-effective, full-featured system that has all of the advanced, patented VisionGauge software capabilities. This system is especially well suited for lower volume applications.Available in both Horizontal and Vertical Configurations. Patented VisionGauge CAD Auto-Align and CAD Auto-Pass/Fail tools provide fast, accurate and operator-independent results. 3 axis inspection and measurement system with manual stage movements
-
Product
Two Channel Phase and Amplitude Noise Analyzer
DCNTS -190
-
The DCNTS is a two channel Phase and Amplitude noise analyzer. Its dual demodulator architecture allows the system to use cross-correlation to cancel its internal noise and limitation; it is like comparing the outputs of 2 systems and only display the similarities while rejecting differences. Its main extension is the Residual Noise measurement front-end which includes all necessary hardware to automatically measure residual noise on 2-ports devices either in RF frequencies or microwave. It could be a frequency multiplier or divider, an amplifier or any other phase coherent input to output device.
-
Product
Ethanol In Gasoline Analyzer
InfraCal 2 ATR-E
-
The InfraCal 2 Ethanol Blend Analyzer for measuring percent ethanol in gasoline is the ideal solution where a quick, accurate, on-site measurement is required and a single, repetitive ethanol blend analysis is needed. The InfraCal 2 ATR-E is based on proven IR technology, and used by fuel terminals, laboratories and regulatory agencies worldwide. The compact, easy-to-use InfraCal 2 ATR-E has a measurement range of 0-20 & 70-98%% ethanol in gasoline and an accuracy of +/- 0.2%. These results are comparable to ASTM D4815.
-
Product
Analog Sequencers
-
Analog sequencers from Analog Devices integrate accurate comparators with the control functionality of power-on and power-down sequencing for voltage regulator banks. The comparators monitor the regulator voltage outputs and trigger the turn on of next rail in the system after a preconfigured time delay. Some members of this portfolio can be cascaded together, which provides scalable solutions to expand functionality across multiple devices. Our analog sequencers provide an easy to use solution for power sequencing challenges in cellular infrastructure, telecommunication, data communication, and data center applications.
-
Product
32-CH Discrete Input Modules with U Profile
HSL-DI32-UD
Digital Input Module
HSL U series is designed as compact & horizontal-placed slave module. For I/O module, ADLINK adopts three types of connectors to meet different users' requirements & habits. Compared with past models, U series brings compact size, easier-to-wire and cost-effective advantages for users. DI/O, AI/O and motion control module are supported
-
Product
Mid-Range Gas Filter Correlation CO Analyzer
Model T300M
-
Teledyne Advanced Pollution Instrumentation
The Model T300M CO analyzer measures low to mid ranges of carbon monoxide by comparing infrared energy absorbed by a sample to that absorbed by a reference gas according to the Beer-Lambert law. Using a Gas Filter Correlation Wheel, a high-energy IR light source is alternately passed through a CO filled chamber and a chamber with no CO present. The light path then travels through the sample cell, which has a folded path of 2.56 meters.
-
Product
Near Field Probes
-
A typical emi emission test is performed using broadband EMC antennas such as biconical, log periodics, Combilogs and horns. These antennas usually placed at 1, 3 or 10 meter distance as required by the test specification. These is considered far field measurements and the emission limits are given for the specific distance by the specification. During EMI compliance measurements, the emissions levels from products are compared with these limits. If the product exceeds these limits it is considered failing. These tests are typically conducted in a open area test site IOATS) or inside an anechoic chamber.
-
Product
Continuous-wave (CW) Lasers
-
Continuous-wave lasers (cw lasers) emit a continuous laser beam as compared to ultrafast or pulsed lasers that emit a pulsed laser beam. Spectra-Physics offers wavelength tunable cw lasers, standard cw lasers, quasi-cw lasers, and accessories for continuous-wave lasers.
-
Product
Charge Converter
CH-6130/6140
-
The CH-6130/6140 charge converter is a simplified type of charge amplifier converting charge signal to voltage.It can be connected directly to an input BNC connector of a CCLD applicable equipment such as FFT analyzer or vibration comparator, enabling direct connection of a charge output pickup without suing a box type amplifier.
-
Product
Correlation Analysis
-
EDM Modal Correlation Analysis allows the user to correlate two modal models; EMA and/or FEA models. Comparing the experimental data with that acquired through finite element analysis helps in validating the test results. Users can import the geometry model and mode shape data from FEA or EMA software.
