PMC Modules
-
Product
PMC Modules
ARINC 429
-
Sycos range of ARINC 429 PMC modules offer the user up to 32 channels on a single width PMC module. Each channel can be programmed independently to operate at either high or low speed. Firmware options available for Tx Error Insertion and Rx Error Reporting are available.
-
Product
ARINC 429 Test And Simulation PMC Module
PMC-429
-
*4, 8, 16 or 32 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*PXI interrupts, star trigger, and PXI clock*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Sorting according to SDI field*VXI Plug & Play driver including soft front panel*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
Product
PMC Module
PMC-softDAC
-
2 µS settling time, 0-5v range• Six Programmable OutputRanges per channel• Unipolar: 0V to 5V, 0V to 10V• Bipolar Mode: ±5V, ±10V,±2.5V,–2.5V to 7.5V• 1LSB Max DNL and INL Over theIndustrial Temperature Range• 64k DAC buffers• Power-On Reset to 0V• Flash ram for configuration file• Two stage buffers• Global output buffer w/ internal orexternal triggering
-
Product
CompactPCI (3U) Generic Carrier Card For PMC(PCIbus Mezzanine Card) Modules
ACC-1
-
cPCI (3U) generic carrier card for PMC (PCIbus mezzanine card) with 1 PMC slot. Modular solution combines any AIM PMC module for AFDX®/ARINC664P7, ARINC429, MIL-STD-1553 or any standard 3rd party PMC module.
-
Product
PMC Module
PMC-CycloneII-64LVTTL
-
User Programmable Altera Cyclone II FPGA 672 BGA, EP2C35, EP2C50, EP2C70, Stand alone possibility, Single wide PMC Module, 64 LVTL, Optional User clock oscillator
-
Product
VME Generic Carrier Card For PMC(PCIbus Mezzanine Card) Modules
AVC-2
-
VME64x (6U) generic carrier card for PMC (PCIbus mezzanine card) with 2 PMC slots. Modular solution combines any AIM PMC module for AFDX®/ARINC664P7, ARINC429, MIL-STD-1553 or any standard 3rd party PMC module.
-
Product
VME PowerPC Single Board Computer
DP-VME-0405
-
The DP-VME-0405 is a high performance VME PowerPC single board computer(SBC) that features the latest PowerPC 7410, SDRAM with error detection and correction and a dedicated L2 cache bus. The board's architecture strikes a balance between high performance processing power, memory and I/O resources. With its vast array of interfaces, the DP-VME-0405 allows the user to perform intensive I/O while permitting rigorous computing. Two industry standard PMC slots enhance the I/O capability, allowing the users to provide program specific features by using commercially available PMC module.
-
Product
6U VME Carrier for PMCs and PrPMCs
Ti4400
-
The Ti4400 is a 6U PMC/PrPMC carrier for VME systems and forms the basis of a flexible I/O system. The user can integrate two single PMC modules or one double-wide PMC.
-
Product
PMC to 3U CompactPCI Carrier
7000
-
This low-cost family of CompactPCI adapters enables the use of standard and custom 32-bit based PMC modules in a 3U or 6U CompactPCI system.
-
Product
VME Generic Carrier Card For Conduction Cooled PMC(PCIbus Mezzanine Card) Modules
AVC-2-CC
-
VME64x (6U) generic carrier card for conduction cooled PMC (PCIbus mezzanine card) with 2 PMC slots. Modular solution combines any AIM conduction cooled PMC module for ARINC429, MIL-STD-1553 or any conduction cooled 3rd party PMC module.
-
Product
PMC Products
-
Our PMC modules are based on technology and circuit designs with time-tested reliability in thousands of installations. Great effort goes into selecting high-performance parts to withstand the demands of military, aerospace, and manufacturing applications. Most models are available with extended temperature ranges for reliable operation in harsh environments. Acromag products are also designed for the long lifecycles required for OEM and defense projects.
-
Product
PMC-BiSerial II-NG1
-
The PMC BiSerial-II NG1 is part of the PMC Module family of modular I/O components by Dynamic Engineering. The PMC BiSerial-II is capable of providing multiple serial protocols. The NG1 protocol implemented provides two full-duplex RS-422 UART interfaces with error detection, two half-duplex RS-485 custom "index" interfaces, external clock input, two clock outputs, and various discrete signal inputs and outputs, all using RS-485 transceivers
-
Product
32x ADC, 16x/0x DAC & 8x Digital I/O PMC Module
TPMC533
-
The TPMC533 is a standard single-wide PCI Mezzanine Card (PMC) compatible module providing 32 channels of simultaneous sampling true differential bipolar 16bit analog input, 16 or no channels of simultaneous update single-ended unipolar/bipolar 16bit analog output and 8 channels of tri-state 5V-tolerant TTL digital input/output. All signals are accessible through a HDRA100 type front I/O connector.
-
Product
CompactPCI
3U PMC Carrier
-
This conduction cooled 3U CompactPCI single slot PMC provides an active interface between the CompactPCI bus (backplane) and a PCI Mezzanine Card (PMC). This product addresses the needs of aerospace, military, and rugged applications. It contains a thermal heat frame made of aluminum that fits together with conduction cooled PMC modules. Conduction cooling conducts heat away from the hot spots of the board and transfers the heat to the card edges and to the system chassis. No active ventilation is necessary inside of the system, which means the boards are sealed from the environmental influences found outside of the chassis. The heat frame and integrated wedge locks for the conduction cooling stiffens carrier and PMC module enabling the board to resist high shock and vibration.
-
Product
Mezzanine Module
RS485-MOD2
-
Curtiss-Wright Defense Solutions
The RS485-MOD2 is a front panel mezzanine module designed to provide serial I/O functionality to Curtiss-Wright FPGA-based processing PMC and XMC modules including the PMC-FPGA03, PMC-FPGA05 and XMC-FPGA05D. This RS485 I/O module provides 33 channels of EIA-485 or EIA-422B serial I/O. Each channel is configured as an input or output. The serial protocol and timing are handled by the host FPGA.
-
Product
Avionics Grade Power PC
DP-VME-0450
-
The DP-VME-0450 is a high performance VME PowerPC single board computer(SBC) that features the latest PowerPC 7410, SDRAM with Error detection and correction and a dedicated L2 cache bus. The board's architecture strikes a balance between high performance processing power, memory and I/O resources. With its vast array of interfaces the DP-VME-0450 allows the user to perform intensive I/O while permitting rigorous computing. Two industry standard PMC slots enhance the I/O capability, allowing the users to provide program specific features by using all commercially available PMC module.
-
Product
Audio Card I/O Modules
PIM481-J/DSUB
-
The PIM481-J PMC I/O Module, with four 3.5mm stereo connectors and the PIM481-DSUB PMC I/O Module, with D-sub for rear I/O can be mounted on a rear transition module (RTM).
-
Product
PMC Carrier Card
APC-PMC
-
This board provides an easy and low cost solution that enables use of a PMC mezzanine I/O module in a standard PCI computer system. The carrier card acts simply as an adapter to route PCI bus signals to and from the PMC module through the PCI card slot edge connector.
-
Product
Interface
RCNIC-A2PA
-
The RCNIC platform is a high performance PMC module for the AFDX/ARINC 664 protocol. With two independent ports for traffic monitoring, traffic generation, external triggering and analysis, the RCNIC provides high-resolution time-tagging of incoming packets simultaneously with highly accurate traffic generation.
-
Product
PMC Module
XMC-603
-
Curtiss-Wright Defense Solutions
The XMC-603 PMC module allows customers to readily incorporate MIL-STD-1553 into military and aerospace embedded computing systems. As one of several products in our comprehensive range of rugged XMC modules, the XMC-603 integrates well with other elements of our product line, featuring technical support, lifecycle management services, and assured long-term availability.
-
Product
AFDX ® / ARINC 664 Test And Simulation PMC Module
PMC-664
-
*Supports IEEE 802.3 10/100/1000 Mbit / s full duplex Ethernet connections*Uses SFPs to support both electrical and optical interfaces*Half-size PCI / PCI-X modules*Simulates multiple AFDX® / ARINC 664 end systems*Standard Ethernet processes simultaneous to AFDX® / ARINC 664*Up to 128 output VLs and 512 input VLs*Upper layer protocol handling (ARINC 653, UDP, IP) managed onboard*DMA for high data rate applications*Windows XP / 7, Linux, and LabVIEW Real Time Drivers & APIs (others on request)Easy to use tool for configuring A*FDX® / ARINC 664 end systems (XML based)
-
Product
PMC Module
PMC-1553
-
Operating temperatureCommercial: 0 to +55 °COptional: -25°C to +80°C• Non-operating: -40°C to 85 °C• Airflow requirement: .5 CFM• Humidity: 5 to 90% (non-cond.)• Altitude: 0 to 10’000 ft
-
Product
PCIe Carrier Boards
-
These non-intelligent carrier cards interface XMC and PMC mezzanine modules and Industry Pack Modules to a PCI Express bus in a PC-based embedded computer.
-
Product
Mezzanine Cards
-
PMC and XMC are the quasi standard for mezzanine cards in VME systems. esd's PMC and XMC modules extend your system with a bus interface (CAN, EtherCAT, Ethernet) or an intelligent sub system (e.g. XMC-CPU/2041, PMC-CPU/440). Furthermore esd develops customized PMC and XMC modules. VME systems without PMC slot can be extended with an esd VME-PMC-Caddy or PCIe-XPIMC-Carrier board.
-
Product
64x LVDS Module
LVDS-MOD4
-
Curtiss-Wright Defense Solutions
The LVDS-MOD4 is a front panel mezzanine module designed to provide LVDS I/O functionality to Curtiss-Wright Xilinx Virtex II-Pro and Virtex-5 FPGA-based processing PMC modules, the PMC-FPGA03, PMC-FPGA05, and XMC-FPGA05D. This module provides 64 differential I/O pairs to the front panel. The LVDS-MOD4 LVDS I/O module is aimed at embedded application development.
-
Product
ARINC825 Cards
-
AIM’s ARINC825 cards can work either with full functionality as an active CAN node for testing and simulating or in listening only mode for monitoring and recording purposes of Avionic CAN bus (ARINC825) applications on up to 4 electrically isolated CAN bus nodes concurrently. All nodes are in conformance with the ISO11898-1/-2 standard. They are accessible by software separately and can be used as 4 independent CAN bus nodes. An onboard IRIG-B time decoder allows users to accurately synchronize single or multiple modules to a common time source. All supported signals are available through front I/O and rear I/O interface. ARINC825 cards consist of FPGA based CAN interface controllers as well as a FPGA based 32-bit microcontroller core and a separate processor for IRIG-B synchronization with high resolution time stamping. All nodes are operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s with the intelligence to process scheduling of CAN frames in real time onboard to significantly off-load the host processor.For embedded applications the AMC825-4 PMC module is available in a conduction cooled version. Using AIM’s family of PCI, CPCI (3U and 6U) and VMEbus carrier cards for PMC our clients have off the shelf solutions in a broad range of card formats. ARINC825 (CAN bus) modules are delivered with an Application Programming Interface (API) and Driver Software compatible with Windows, Linux and VxWorks.An ARINC825 Resource Component is available for AIM’s PBA.pro™ databus test and analysis tool including Tx and Rx simulation capabilities, a Chronological Bus Monitor and support for decoding of payload data within CAN messages. This allows to implement a powerful ARINC825 (CAN bus) analyzer or a complete test system in conjunction with other AIM avionics databus interfaces and PBA.pro™ supported 3rd party hardware.
-
Product
PCIe Carrier For PMC And PrPMC
PCI104
-
The PCI104 is a PCIe carrier for PCI Mezzanine Cards (PMC) or Processor PCI Mezzanine Cards (PrPMC). The PCI104 carrier allows simplified testing of PMC/PrPMCs and their associated PMC I/O Modules (PIMs) by using a PC environment during board development or deployment. The PCI104 can also reduce the costs of manufacturing PMC/PrPMCs by allowing manufacturers to use off-the-shelf PCs for functional testing. The PCI104 converts the PCIe x4 edge connection to PCI-X via a PCIe to PCI-X bridge. The trace lengths to the PMC/PrPMCare kept to a minimum so the PMC/PrPMC can run with a133MHz PCI-X clock speed. The J4 connector of the installed PMC/PrPMC is routed to a 96-pin DIN connector per theVITA-35 specification. The PCIe to PCI-X bridge can run in either transparent or non-transparent mode and can also operate in forward or reverse mode. The PCI104 has a fan mounted on the board to cool the PMC/PrPMC. The fan can easily be removed for testing and probing of hosted card.
-
Product
PCI Express x1 PMC Carrier
TPCE261
-
The TPCE261 is a standard height PCI Express Revision 2.0 compatible module that provides one slot for a single-width PMC module used to build modular, flexible and cost effective I/O solutions for all kinds of applications like process control, medical systems, telecommunication and traffic control. The TPCE261 is a versatile solution to upgrade well known PMC I/O solutions to the PCI Express signaling standard.
-
Product
PMC-to-PCI Express Adapter (PCIe/PCI-e)
5243
-
Our PMC-to-PCI Express Adapter (PCIe/PCI-e) 1X (5243) permits the use of a single-wide PMC module in a 1x PCIe slot. The A and C rows of a 96-pin DIN connector, located toward the rear of the board, connect with the 64-pin user I/O connector (J4/P4) on the mezzanine card.
-
Product
Socket Saver
4690
-
The Technobox PMC Socket-Saver permits cost effective volume testing of PMC modules when used with Technobox P/N 3390 ?PMC to PCI adapter for Test.? It may also be used to reduce wear and tear on Technobox P/N 1518/1523 (?Extender/Preprocessor?).
