Phase Angle
Measure electrical phase angles or visualize stero sound.
See Also: Phase, Phasing, Phase Standards, Phase Meters, 3 Phase, Phase Angle Meters, Phase Angle Voltmeters, Phasors
-
-
Product
Phase Monitoring / Potential Selector Relay
-
This is a phase failure relay suitable for 3 phase supplies. The relay is designed to automatically change over from the primary supply to the secondary supply if any phase of the primary supply has faulted.
-
Product
Phase Verification Bridges
5002
-
Clarke-Hess Communications Research
The Model 5002 Phase Verification Bridge set comprises passive devices that are used in conjunction with Model 5500-2 Phase Standard and an output null indicator such as a true rms voltmeter, an oscilloscope or a wave analyzer to verify that the Phase Standard is continuing to operate within its specified phase accuracy limits.
-
Product
Two Phase AC Motor Drive
MS 2014
-
Excellent High Speed Response. With help of semiconductor high end motion control algorithm and advanced common gain concept, a high speed response is achieved, therefore satisfying all motion control needs. Built-in Accuracy Improvement Features. Drive include features to improve total positioning accuracy of the mechanical system.
-
Product
Digital Image Correlation System for Complete 3D Warpage, Thermal Expansion, and Strain Analysis of Materials and Components in the Heating and Cooling Phase
Q-400 TCT
-
The Q-400 TCT system is designed for complete three-dimensional and highly sensitive warpage, thermal expansion measurement and strain analysis of materials and components in the heating and cooling phase. Areas from 50 mm x 70 mm down to 2 mm x 3 mm can be investigated. Measurements can be done from room temperature up to 300°C and down to -40°C. The system is specially suited for thermal expansion measurement of electronic components and is frequently used in the development and testing of complex anisotropic materials, components, and structures in electronic applications.
-
Product
Three Phase Power Calibrators And Tester Of Power Engineering Devices
C300B
-
Calmet Smart Calibration Devices
Three phase, class 0.02 and 0.05 power quality calibrator up to 120A (360A) and 560VAC with programmable power quality parameters. It makes possible to make automatic test of electricity meters, measurement transducers, current transformers and protection relays.
-
Product
Analog Phase Shifter
-
Analog Devices analog phase shifters change the phase of RF, microwave, and millimeter wave signals. Our technology features consistent insertion loss vs. phase shift, monotonic phase shift, low insertion loss, and a compact size that makes it ideal for multiple applications, including:• Fiber optics• Military• Test equipment
-
Product
Phase Meter Current Shunts
610 and 650
-
Clarke-Hess Communications Research
The Model 610 and 650 Current Shunts are specifically designed to operate with the Model 6000A Precision Phase Meter. These shunts are frequency tuned to have negligible phase shift (less than 5m) at 50/60Hz making them ideal for line frequency applications. They can also be idealized for other frequencies as specified by the user. Consult factory for details.
-
Product
Wide Angle High Definition Underwater Camera
Surveyor-WAHD
-
The Surveyor-WAHD underwater camera is designed to provide a 14% increase in angle of view, from the previous WAHD camera, whilst remaining compact and very competitively priced. It is ideal for ROV inspection tasks, scientific observation and broadcast applications.Video output is available as component (Y/PbPr), utilising standard connectors or HD-SDI on hybrid 75 Ω coaxial or fibre optic connectors, a composite video output is also available.
-
Product
Three Phase Secondary Current Injection Test Set
TEST-330B
-
Beijing GFUVE Electronics Co.,Ltd.
Three phase secondary current injection test set is testing relay set, protective device, instruments, output ac dc current and voltage source, embedded Window XP system.
-
Product
Phase Noise Measurement Solutions
-
Keysight offers dedicated phase noise measurement solutions to simplify your measurements and maximize your efficiency. Building on 30 years of low phase noise and RF design and measurement experience, our innovative solutions are designed to provide the most accurate phase noise data possible, and are economically tailored to fit your specific performance and application needs - now and well into the future.
-
Product
Three Phase AC Voltage Source
EAC-TAVS
-
Electronic Test & Power Systems
The EAC-TAVS is a series of programmable high power AC voltage sources. Each system provides a three phase true sinewave output as standard. Each unit is built in a freestanding cabinet. The output frequency is adjustable in the range of 45 - 105Hz. Different frequency ranges are optional, with up to 805Hz possible. An RS-232 and CAN interface are provided as standard. The high resolution TFT front panel displays a host of measurement and setting functions. Besides standard models, other nominal power levels and voltages can be user specified. Single phase and bidirectional versions are available on request.
-
Product
Ultra-low Noise Phase Inverter - Buffer
WMA-IB-LN
-
The WMA-IB-LN can be used to double the output voltage of two high voltage amplifiers by driving them in bridge mode, or as high impedance input buffer while maintaining precision and ultra-low noise. The WMA-IB-LN model has been designed specifically for the Falco Systems WMA-200 high voltage amplifier. Two WMA-200 amplifiers combined with one WMA-IB-LN provide unprecedented noise performance and output voltage range.
-
Product
36" Support Angles
SA-36
-
36" support angles provide 3” of horizontal surface along each side of vertical cabinet for supporting instruments.
-
Product
Phase Shifters
-
Essential function blocks such as Teledyne Microwave Solutions' Phase Shifters provide reliable, high performance for RF/Microwave commercial, industrial and military systems.
-
Product
Header/Shroud Right Angle Kit, ITA, 90 Series, QuadraPaddle, for Custom PCB Mounting
510109316
ITA Module
Header/Shroud Right Angle Kit, ITA, QuadraPaddle, for Custom PCB MountingThis kit is for mounting QuadraPaddle ITA modules to custom-designed PCBs. Requires QPITA module p/n 510151107.If you do not have ITA module p/n 510151107, purchase the full ITA QP mounting kit instead, p/n 510151121.
-
Product
Spectral Phase Measurement
Avoca SPIDER System
-
Spectral phase interferometry for direct electric-field reconstruction (SPIDER) is one technique that can recover the spectral phase of an input pulse, without needing any reference pulse. SPIDER interferes two pulses which areseparated in time and in frequency, and the resultantinterferogram is read by a spectrometer.
-
Product
500-Pin Connector, Female Right Angle PCB Mount, 2 Amp
C500RFX-XPR-5A
-
The 500-Pin connector is used on switching products to provide a very high density 2A connector solution. This accessory allows a user to create their own PCB based termination solution mounted on a circuit board. The interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
Product
Phase Sensors and Phase Sequence Relays
-
Protect aircraft equipment & other devices from damage due to phase loss or reversal with DARE?s phase sensors & monitors. Designed to monitor the phase sequence of three phase power, DARE?s phase sensors will protect electrical equipment that is sensitive to incorrect phase sequence (rotation), phase loss, or phase reversal.
-
Product
Fully Automatic Close Link Single Phase Energy Meter Test bench
SY 8125
-
Hong Kong Songyang Industrial Ltd.
The devices are fully made by aluminum alloy materials and the table board is composed of fireproofing and heat-proof materials. The output voltage and current use soft startup and stop. It has the protection functions of voltage short circuit, current open circuit and power amplification exception. The device has the features of high stability, good reliability and large output power
-
Product
Multi-Purpose Digital H. V. Phasing Meter
MDP-50K
-
Standard Electric Works Co., Ltd
● AC 50kV and DC 50kV measurement with direct reading.● 4000-count LCD.● Input impedance : 400 Mohm● Auto-ranging : AC : 4.000kV / 40.00kV / 50.0kV DC : 4.000kV / 40.00kV / 50.0kV● MDP-50K must be connected with an approved hot stick, such as HS-175, HS-120.● Polarity indication : Positive / Negative● Backlight function.● Auto power off.● Power source : 1.5V(AA) alkaline battery × 2.● Low battery indication(Multi-level). ● Protection class : IP66
-
Product
68-Pin SCSI Micro-D Male Right Angle PCB
40-963-068-RM
SCSI Male Connector
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
Product
200-Pin LFH Connector, PCB Mount, Right Angle Female
40-963-200-RF
-
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. It is suitable for use with a variety of products. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
Product
Phase Noise Measurement Solution, 50 kHz to 110 GHz
E5505A
-
The Keysight Technologies E5500 Series of phase noise measurement solutions offers the most flexible set of measurements on one-port VCOs, DROs, crystal oscillators and synthesizers. Two-port devices, including amplifiers and converters, plus CW, pulsed and spurious signals can also be measured. The E5500 measurements include absolute and residual phase noises, AM noise, and low-level spurious signals. The stand-alone instrument architecture easily configures for various measurement techniques, including the PLL/reference source technique, residual and FM discriminator methods.
-
Product
OPTICAL PHASE NOISE TEST AND MEASUREMENT SYSTEM
-
OEwaves’ HI-Q® Optical Test Measurement System utilizes a homodyne methodology for automated measurement capable of testing ultra-low phase noise laser sources. The user friendly test system is capable of rapidly measuring laser phase noise and estimating its FWHM linewidth down to < 3 Hz without complex setup or reference lasers normally required to make such a narrow linewidth measurement.
-
Product
Phased Array Acquisition and Analysis Software
Prelude
-
Prelude is a powerful and flexible software package. At TPAC, we understand our customers have a heavy investment in scanning equipment. With this in mind, we have developed a software suite that is adaptable and complimentary to your existing devices.
-
Product
High Speed Phase Inverter - Buffer
WMA-IB-HS
-
The WMA-IB-HS can be used to double the output voltage of two high voltage amplifiers by driving them in bridge mode, or as high impedance input buffer while maintaining precision, high speed and low noise. Because of its high bandwidth, the WMA-IB-HS model is ideal for the Falco Systems WMA-100 or WMA-300 amplifiers. It can also be used with all other Falco Systems HV amplifiers, or even with high voltage amplifiers of another brand.
-
Product
Phase Sequence Indicators (Contact Type)
888 PMR
-
Standard Electric Works Co., Ltd
● Indicates phase rotation. ● Indicates phase presence.● Indicates motor rotation/wiring.● Indicates battery status.● Phase rotation and motor rotation indication works from as low as 1Vac.● Small, rugged enclosure.● Color coded test leads.● Phase presence indication from as low as 100 Vac. ● Very low consumption.● Fused. ● Lightweight, robust and compact.● Works from 2 Hz to 400 Hz Sine.
-
Product
Connector, 104-Pin D-Type Male, PCB Mount, Right Angle, 4-40 UNC
40-963-104-RM
D-Sub PCB-Mount Connector
This 104-pin male D-type connector allows users to create their own connection solutions. Right angled PCB mounting - supplied with 4-40 UNC screwlocks. This connector is not suitable for direct connection to Pickering modules that use the 104-pin D-type connector.
