RS-232
A standard interface for serial binary data interchange defining voltage levels for logical one and logical zero, standard transmission speed and connector types.
See Also: Serial, I2C, LIN, Can bus, ExpressCard, Fieldbus, FireWire, RS-485, PCI Express, Serial ATA, Serial Peripheral Interface, SMBus
-
Product
Single Port RS-232 Interface
PCI-COM232
-
Serial ports: 1Configured: Address and interrupt configured through PCI BIOS and supplied driversMax. baud rate: to 460.8 Kbps, software selectable per channel for 115.2, 230.4, or 460.8KbpsSerial modes: 5, 6, 7, or 8 data bits; odd, even or no parity; 0, 1 or 2 stop bitsUART: 16C550 standardInterrupt Status: Each UART interrupt status read from any UARTís Scratchpad RegisterConnector: 37 position D-type with cable to DB-9 (DB-25 optional)Power: +5V only
-
Product
RS-232 Passive Tap Module
EZ-TAP™
-
Stratus Engineering’s EZ-Tap hardware module is a low-cost hardware bus analyzer and protocol analyzer solution that uses a traditional dual COM port approach to RS232 interface monitoring.
-
Product
- RS-232 to RS-485 2 Wire with LCD Display
Model 366
-
FEATURES: DataSpy® Status Display; Implements Low Cost LAN; Supports 32 Users; Uses Single Twisted Pair; External DTE/DCE Switch; Programmable Contention; Selectable Termination. The Model 366 allows interfacing RS-232 based equipment with networks/equipment using RS-485.
-
Product
RS-232 to RS-485 Optically Isolated Interface Converter
Model 8322
-
FEATURES: 4 Wire-Master/Slave Operation; Active Mode Control Via RTS or Data; Opto Isolation; Built-in Power Supply; Internal Microcontroller; 38.4 KBPS Data Rate; DIN Rail Mountable; Programmable Terminations. The Model 8322 RS-232 to RS-485 Interface Converter allows information exchange in half duplex mode over two twisted pairs.
-
Product
RS-232 to RS-422 Optically Isolated Interface Converter
Model 265
-
FEATURES: Eliminates Ground Loops; 19.2 KBPS at 2 Miles;TD and RD Indicators; Use in Pairs as Double Isolated Short Haul Modems; Use in Pairs as Double Isolated Short Haul Modem. Total isolation between RS-232 based systems and RS-422. Unique circuitry allows the RS-422 port to withstand surges exceeding 10 kilovolts.
-
Product
RS-232 Auto Powered Line Driver
Model 201
-
FEATURES: Operates with only Pins 2(TD), 3(RD), & 7(GND); Screw Terminals and RJ-11; DTE/DCE Switch; Built in Surge Protection; Male or Female RS-232; 19.2 KBPS, Full Duplex, 2.1 Miles. The Model 201 RS-232 Auto Powered Line Driver requires only TD, RD, and signal ground for power and full duplex operation up to 19.2 K BPS.
-
Product
Four And Two-Port Multi-Protocol RS-232/422/485 M.2 Cards
M.2-COM-4SM Family
-
The M.2-COM-4SM family of cards feature high performance 16C950-class UARTs. Available in 4-port and 2-port versions, each port is capable of communication speeds up to 921.6kbps in RS-232 (differential modes support speeds as high as 3Mbps) and has 128-byte deep transmit and receive FIFOs. Large FIFOs protect against data loss in multitasking operating systems, reduce CPU utilization, and improve data throughput, while reducing or eliminating inter-character or inter-packet pauses. The advanced integrated circuit with pre-scalar supports a wide variety of custom baud rates, and any rates not otherwise achievable can be supported via a custom factory-installed crystal oscillator (up to 10Mbps!).
-
Product
2-Port RS/232/422/485 Async Serial Communications Adapter PMC
2901
-
The 2-port Async Communications Adapter is a costeffective solution for providing additional RS232/RS422/ RS485 based serial ports for a host processor. Using configuration switches on the PMC board, each port is independently set-up at either RS232 or RS422 levels. In the RS422 case, an additional option is provided to transmit data on the receive data line in an RS485 fashion.
-
Product
- RS-232 to RS-422/RS-485 Converter
Model 285
-
FEATURES: User Selectable RS-422 or RS-485; User Selectable 2 or 4 Wire RS-485; Intelligent Control Of RS-485 Transmitter And Receiver; TD & RD LED's; DTE/DCE Compatible; Data Rates Up to 64 KBPs. The Model 285 RS-232 to RS-422/RS-485 Converter is a unique interface converter that can be configured to operate in compliance with RS-485 or RS-422 equipment, and RS-232.
-
Product
8 Serial Communication Channels, Programmable RS-232/422/485 Non-Isolated
SC3
-
Serial Communication Module SC3 provides up to 8 high-speed, programmable RS-232, RS-422, RS-485, non-isolated communication channels. Each channel is programmable for either Serial Communications (SC) protocol or General Purpose I/O (GPIO) modes as either RS-422/485 (differential) or RS-232 (single ended) hardware level interfaces.
-
Product
RS-232 to RS-422/RS-485 Interface Converter
Model 9365
-
FEATURES: DIN Rail Mountable; User Selectable RS-422 or RS-485; User Selectable Two- or Four-wire RS-485; DataSpy® LCD Display; Intelligent Control of RS-485 Transmitter and Receiver; DTE/DCE Compatible; Data Rates Up to 115.2 kbp.
-
Product
PC/104-Plus And PCI-104 8-Port RS-232 Serial Communication
P104-COM232-8 and 104I-COM232-8
-
The P104-COM232-8 (PC/104-Plus) and 104I-COM232-8 (PCI-104) are PC/104-based eight channel RS-232 communication peripherals. Based on the XR17D158, the boards have eight enhanced 16550 UARTs, each with a set of modem signals (CTS, RTS, RI, DTR, DSR, CD). A 460Kb/s rate is guaranteed for all channels with up to 3K Ohm 1000pF loads. All interrupts may be monitored at a 32-bit status register. Each UART has both a 64 byte transmit and a 64 byte receive FIFO.
-
Product
Serial RS-232 Expansion Connector Accessory for USBHub3c
-
Used for connecting a serial RS-232 interface to the control the USBHub3c through the expansion interface connector. Screw terminals are provided for the RS-232 interface. While this board provides for wiring connections, a host machine external to the USBHub3c is required for this control interface.
-
Product
- RS-232 Opto Isolation Module
Model 268
-
FEATURES: Total Electrical Isolation; Eliminates Noise Problems; Eliminates Ground Loops; Use for Data & Control; UL Components. The Model 268 Opto Isolation Module provides a communications link that has no electrical connections from one port to the other.
-
Product
3U CompactPCI® RS-232/422/485 Serial Communication Card
MIC-3955
-
The MIC-3955 is a low power 4-port or 8-port RS232/RS422/RS485 serial board with 3U CPCI form factor and is based on the EXAR PCI controller. MIC-3955 is PICMG 2.0 Rev. 3.0 compatible. Rear board module are named MIC-3527XX. The MIC-3955 supports front IO or rear IO with 4-port and 8-port, and every channel is independent.
-
Product
Cable Assembly, Receiver, TriPaddle, 36", 2 9-Pin Female D-Subs, for RS-232
540127010201
Cable Assembly
Cable Assembly, Receiver, TriPaddle, 36", 2 9-Pin Female D-Subs
-
Product
PCI Express 16-Port RS-232 Serial Interface
7161e
-
The 7161e provides sixteen RS-232 serial ports capable of data rates to 460.8K bps. Each RS-232 port implements all modem control signals for maximum compatibility with a wide range of peripherals. The board is PCI Express X1 compliant and utilizes 16C854 UARTs to provide 128-byte Tx/Rx FIFOs for maximum reliability in data intensive applications.
-
Product
Isolated RS-232
-
Analog Devices offers a wide range of RS-232 transceivers to suit many applications. As RS-232 cable networks and the systems to them can be vulnerable to voltage spikes and ground loops, we have developed a number of innovations that protect against these issues and create an isolated RS-232 environment. We accomplish this through our isoPower® integrated dc-to-dc converters, as well as our iCoupler® technology, which enable the power isolation and signal isolation required for system reliability in a noisy environment.
-
Product
68VHDCI-DB9M Serial Cable - 68-POS VHDCI to DB-9M, 8-Port RS-232, 1M
197545-01
Serial Cable
Serial Cable - 68-POS VHDCI to DB-9M, 8-Port RS-232, 1M
-
Product
Datalogging Digital Sound Level Meter with RS-232 Software and Cable
735
-
Whether you are testing for OSHA compliance, quieting equipment, or monitoring the roar of a stadium crowd, B&K Precision's Sound Level Meters can get the job done. The model 735 Sound Level Meter provides 30~130 dB capability in three convenient measurement ranges Low, Med and Hi with an accuracy of ±1.5 dB. The meter meets the IEC 651 Type II and includes frequency weighting A & C and fast and slow time weighting.
-
Product
RS-232 to RS-422/RS-485 Converter
ND-6520
-
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
Product
RS-232 and RS-562 Transceivers
-
Analog Devices offers single, dual, and combination transceivers of up to five RS-232/RS-562 drivers and receivers for 1.8 V to 5.5 V power supplies. Data terminal equipment (DTE) or data communications equipment (DCE) configurations are also available in 3.3 V or 5 V versions. Galvanically isolated modules break ground loops and provide a convenient, self-powered, isolated, low EMI solution that drastically reduces component count and design complexity.
-
Product
RS-232 Cable, 9 Pin (f) To 9 Pin (f)
34398A
-
The Keysight 34398A is an RS-232 cable, 9 pin (f) to 9 pin (f). Standard RS-232 cables are easy to find, but making them work is a different story. The Keysight 34398A has been verified for compatibility with Keysight's bench instruments to take the mystery out of RS-232 pinouts. The Keysight 34398A includes a 9-pin (f) to 9-pin (f) RS-232 cable and a 9-pin (m) to 25-pin (f) adapter.
-
Product
68SCSI-DB9M Serial Cable, 68 POS SCSI to 8 DB-9, 1 m (RS-232)
185196-01
Serial Cable
Serial Cable, 68 POS SCSI to 8 DB-9, 1 m (RS-232)
-
Product
RS-232
-
The RS-232 family includes transceivers with auto-power-down and standby functions, multi-channel interfaces and driver/receiver circuits. These devices have a 5 V supply or a 3 V to 5 V supply and are ESD protected enabling true RS-232 performance.
-
Product
RS-232 Line Driver with Control Signals and LCD Display
Model 224
-
FEATURES: DataSpy® Status Display; Full Duplex & Handshake; Loopback & DTE/DCE Switch; DC to 19.2 KBPS; Supports DTR & DCD; Optically Isolated. The Model 224 RS-232 Line Driver with Control Signals and LCD Display provides for transmission of a handshake signal in each direction, in addition to communicating full duplex data up to 19.2 KBPS and providing complete optical isolation.
-
Product
Universal PCI, Eight or Four-port RS-232/422/485 Serial Communication Card
LPCI-COM Series
-
The LPCI-COM Series are eight or four-port asynchronous serial communication cards designed for use in PCI bus computers. The cards support RS-232, RS-422, and/or RS-485 communications which can be selected on a port by port basis.
-
Product
- RS-232 to RS-422/RS-485 Concentrator - Wiring Hub
Model 290
-
FEATURES: Break RS-485 Limit, Expand to 496 Nodes 16 Port Capacity; Each Port Settable to RS-422 or 2 Wire RS-485; Provides Isolation Between Ports; All Ports Surge Protected; Increased System Reliability. The Model 290 RS-232 to RS-422/RS-485 Concentrator offers a unique group of features for those applications using RS-422 and/or RS-485 for communications between a multiplicity of devices.
-
Product
RS-232 to RS-422/RS-485 Interface Converter
Model 365
-
FEATURES: User Selectable RS-422 or RS-485; User Selectable 2 or 4 Wire RS-485; DataSpy® LCD Display; Intelligent Control of RS-485 Transmitter and Receiver; DTE/DCE Compatible; Data Rates Up to 115.2 KBPS. The Model 365 multimode interface converter allows operation in compliance with RS-485 or RS-422 equipment, and RS-232.
-
Product
200 KHz LCR Meter w/RS-232 Interface
LCR 200
-
Measurement Parameters : Z , Ls , Lp , Cs , Cp , DCR , ESR , D , Q , and £c. Test conditions : 100MHz , 120Hz , 1KHz , 10KHz , 100KHz , 200KHz Basic Accuracy 0.1% ; Test Voltage: 1Vrms , 250mVrms , 50mVrms , 1Vdc(DCR only). DMM Functionalities. Dual LCD Display with LED backlit
