Interface Devices
soft and hard handshake between devices.
-
product
PCI-8512, 1‑Port, High‑Speed/FD CAN Interface Device
780683-01
The PCI‑8512 is a high-speed controller area network (CAN) flexible data-rate (FD) interface for developing applications with the NI‑XNET driver. The PCI‑8512 excels in applications requiring real‑time, high‑speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
product
Semiconductor Test Hardware Solutions
A critical element of every semiconductor test solution is the interface between the device and ATE. The hardware team at Test Spectrum has produced thousands of successful test interface solutions for some of the most challenging semiconductor products on all major ATE platforms. Our in-house team of PCB design experts has an added advantage of direct access to our senior test engineering staff.
-
product
Interface and Isolation
Analog Devices offers a wide range of digital interface and digital isolators with iCoupler® technology covering the industry’s field bus and peripheral communications standards. Digital isolators, isolated transceivers, isolated A/D converters and isolated gate drivers utilize the award winning iCoupler® and isoPower® technologies for isolation solutions without many of the constraints found in optocouplers. Find design solutions for interface devices including keypad controllers, level translators, and high voltage protection products (channel protection, fault protection, overvoltage protection), and latch-up proof switches and multiplexers.
-
product
PCIe-8431, PCI Express, 8-Port, RS485/RS422 Serial Interface Device
780592-01
The PCIe‑8431/8 is a high-performance interface for high-speed communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between … 4‑ and 2‑wire transceiver modes for full- and half-duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
product
FlexRay Interface Device
FlexRay Interface Devices provide two fully functional FlexRay interfaces, allowing an individual engine control unit (ECU) to be connected to the interface when other cold-start nodes are not available. You also can use the interfaces individually to connect two separate FlexRay networks while maintaining full performance on each interface. FlexRay Interface Devices work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
product
GPIB To ANSI X3.28 Interfaces
ICS's GPIB to ANSI X3.28 Interfaces adapt older devices that use the ANSI X3.28 devices to the GPIB Bus. All ICS GPIB Interfaces are IEEE-488.2 compliant and HP-IB compatible.
-
product
SpaceWire-USB Brick Mk3
326
The SpaceWire Brick Mk3 is a USB 3.0 (also works with USB 2.0 and USB 1.1) to SpaceWire interface device that is suitable for use in all stages of SpaceWire equipment development: initial SpaceWire evaluation, instrument simulation, control system simulation, unit testing, integration support, and EGSE. The SpaceWire Brick Mk3 provides two SpaceWire interfaces, support for high speed data transfer, the capability to inject various types of errors on demand, the ability to transmit and receive time-codes and act as a time-code master, and comes complete with highly optimised host software for low latency transmission of SpaceWire packets directly to and from the host PC.
-
product
Gas Detection System Controller
SMC Sentry IT
The SMC Sentry IT Controller is a powerful network-enabled hazardous gas detection system that operates up to 32 detectors and interfaces with devices over Modbus RTU, 4-20 mA, Sentry PSG Bus, and conventional dry contact. The embedded web application enables users to view important data remotely and provides connectivity into the Industrial Internet of Things (IIoT).
-
product
IP Gateway
SFT3503A
Hangzhou Softel Optic Co., Ltd.
SFT3503A Bidirectional IP Gateway is a head-end interface device which is used for DVB and Ethernet. It can be used both for a receiver and a lancers! On one hand, in the lancers part, this machine can be used for sending IP stream, turning the TS stream into IP Stream. On the other hand, in the receive part; this machine can be used for receiving IP stream, turning the IP stream into TS stream.
-
product
PCI-8513, 1‑Port, Software‑Selectable/FD CAN Interface Device
780684-01
1‑Port, Software‑Selectable/FD CAN Interface Device—The PCI‑8513 is a controller area network (CAN) flexible data-rate (FD) interface for developing applications with the NI‑XNET driver. NI‑XNET software-selectable CAN interfaces offer the best flexibility for CAN development with onboard transceivers for high-speed/FD, low-speed/fault-tolerant, and single-wire CAN as well as any external transceiver. The PCI‑8513 excels in applications requiring real‑time, high‑speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts.
-
product
Serial Interface Device
The Serial Interface Device offers a number of options for connecting to serial hardware. You can choose from Ethernet, USB, PCI, PCIe, or ExpressCard interfaces to add up to 16 serial ports to your system. You can choose from common serial protocols, such as RS232, RS422, and RS485. The Serial Interface Device also offers various isolation, hyperthreading, and multiprocessor compatibility options. Some models also support 4- and 2-wire transceiver modes for full- and half-duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
product
500-Pin SEARAY Cable Assembly, Male to 5x50-Pin D-Type, 2 Amp, 2m, 250 Port
A500RMR-05F050D4B200
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. The male SEARAY connector of this cable assembly is suitable for direct connection to Pickering Interfaces products. Five 50-Pin D-Type connectors allow an interface to other devices. Screwlocks are provided at both ends to secure the cable assembly to mating products.
-
product
PCIe-8510, 2- or 4-Port, PCIe Vehicle Multi-Protocol Interface Device
785324-01
2- or 4-Port, PCIe Vehicle Multi-Protocol Interface Device—The PCIe‑8510 is a hardware-selectable controller area network (CAN) and/or local interconnect network (LIN) interface for developing applications with the NI‑XNET driver. The PCIe‑8510 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
product
Analog Device Interface
ADI-123
Model ADI-123 Analog Device Interface offers the means of computer interfacing almost on any device whic is provided with dc inputs and/or outputs, for example programmable power supplies and measuring instruments of all kinds.
-
product
PCIe-8510, 2- or 4-Port, PCIe Vehicle Multi-Protocol Interface Device
785325-01
2- or 4-Port, PCIe Vehicle Multi-Protocol Interface Device—The PCIe‑8510 is a hardware-selectable controller area network (CAN) and/or local interconnect network (LIN) interface for developing applications with the NI‑XNET driver. The PCIe‑8510 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
product
192 Channel Power Supply
HDPMU
Today cost efficiency is more important than ever. Many manufacturers are working on maximizing multi-site testing. Often maximization can’t be done because of limited tester resources. Salland’s HDPMU gives you up to 192 additional independent parametric measurement units (PMU) channels on a single board. Our solution will increase parallel testing without the need for creating complex device interface board (DIB). It can be used for continuity, functional or parametric tests or simply for device setup or loading. Full integration with the Teradyne IG-XL™ Software, easy set-up and high parallel measurement capability will reduce test costs significantly.
-
product
PXI Vehicle Multiprotocol Interface Module
PXI Vehicle Multiprotocol Interface Modules use hardware-selectable NI-XNET Transceiver Cables (TRC) to communicate High-Speed/Flexible Data‑rate CAN, Low-Speed/Fault Tolerant CAN, and/or LIN. Using the NI-XNET driver, you can create applications that require real-time, high-speed manipulation of hundreds of CAN and/or LIN frames and signals. The NI-XNET device-driven DMA engine enables the onboard processor to move frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time. PXI Vehicle Multiprotocol Interface Modules work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
product
78-Pin Connector To Screw Terminal Interface
GT96078
78-Pin Connector to Screw Terminal InterfaceTerminal board interface. Interfaces to 78 pin connector.
-
product
ARINC 429 Interface
RCEI-715A
The RCEI-715A is an intelligent, high-density, Type II PC Card (PCMCIA) interface that provides up to 12 fully independent ARINC 429/575 channels, along with up to 4 bi-directional avionics-level I/O discretes.
-
product
Mini USB To 90 Series Interface
J90USBI
Use in ITA SideRequired Tripaddle Modules VPC 510108126
-
product
PXIe-1486, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO FPD-Link™ Interface Module
787454-01
The PXIe-1486 combines the Texas Instruments Flat Panel Display Link™ (FPD-Link™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1486 makes use of a combination of FPD-Link™ serializers and deserializers with a Xilinx FPGA to provide a high-throughput and customizable FPD-Link™ interface on PXI. The included FlexRIO driver, with LabVIEW FPGA examples, provides access and control for power-over-coax, I²C back-channel communication, and general-purpose input/output (GPIO) communication on the FPD-Link™ channels. The PXIe-1486 is ideal for applications such as in-vehicle data logging, lab-based playback, or hardware-in-the-loop (HIL). FPD-Link is a trademark of Texas Instruments.
-
product
PCI-8513, 2-Port, Software‑Selectable/FD CAN Interface Device
780684-02
2-Port, Software‑Selectable/FD CAN Interface Device—The PCI‑8513 is a controller area network (CAN) flexible data-rate (FD) interface for developing applications with the NI‑XNET driver. NI‑XNET software-selectable CAN interfaces offer the best flexibility for CAN development with onboard transceivers for high-speed/FD, low-speed/fault-tolerant, and single-wire CAN as well as any external transceiver. The PCI‑8513 excels in applications requiring real‑time, high‑speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts.
-
product
Mini USB (90º) To 90 Series Interface (R)
J90USBS
Use in Receiver SideTripaddle modules VPC 510104136 required
-
product
Interface
RPCIE-1553
Abaco Systems RPCIE-1553 is the latest generation of performance and flexibility for MIL-STD-1553 A/B Notice II on a native PCI Express module. Available in -40°C to +70°C temperature with one, two or four dual-redundant channels, the RPCIE-1553 includes advanced API (Application Programming Interface) software that reduces application development time.
-
product
PXIe-1487, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO GMSL™ Interface Module
787458-01
The PXIe-1487 combines the Maxim Integrated Gigabit Multimedia Serial Link™ (GMSL™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1487 makes use of a combination of GMSL™ serializers and deserializers with a Xilinx FPGA to provide a high-throughput and customizable GMSL™ interface on PXI. The included FlexRIO driver, with LabVIEW FPGA examples, provides access and control for power-over-coax, I²C back-channel communication, and general-purpose input/output (GPIO) communication on the GMSL™ channels. The PXIe-1487 is ideal for applications such as in-vehicle data logging, lab-based playback, or hardware-in-the-loop (HIL). GMSL is a trademark of Maxim Integrated Products, Inc.
-
product
MIL-STD-1553 Module
QPM-1553
The QPM-1553 provides the highest level of performance, flexibility and interface density for MIL-STD-1553A/B on a PMC (PCI Mezzanine Card) module. The QPM-1553 is integrated with powerful software that reduces development time. All 1553 databus functionality is supported from our advanced API (Application Programming Interface).
-
product
Embedded Avionics Interfaces
Versatile interfaces that enable embedded systems and computers to communicate with avionics databus networks.
-
product
Interface Panel for SLSC
THROUGHPOINT™
Bloomy's ThroughPoint™ Interface Panel provides a simple, yet highly-flexible connection between the unit under test and resources in a National Instruments Switch/Load/Signal Conditioning (SLSC)-based test system.
-
product
PXI Interface Module, AIT ARINC 429
M3407A
Interface to the LRU in avionics test solution 4, 8, 16, or 32 software programmable Tx/Rx channels with full error injection/detection Programmable high/low speed operation Real-time recording and post analysis of multiple channels Concurrent operation of all Tx/Rx channels PXI triggers, star trigger, and PXI 10 MHz clock
-
product
PXIe Remote Control Interface Module
43-921-003
The 43-921 PCI Express-to-PXI Express expansion kit provides control of PXI Express modules installed in a PXI Express chassis using high bandwidth PCI Express technology. The extension kit can provide up to 4GB/s using PCIe Gen 2 x8 signalling.
