Interface Devices
soft and hard handshake between devices.
-
product
Smart GPIB Serial Interface Board
Model 4808
* Provides smart GPIB-to-serial path for serial devices with RS-232, RS-422 or RS-485 signals.* Provides all IEEE-488.2 functions and the Status Reporting Structure.* Smart firmware automatically passes GPIB data to serial device.* SCPI commands set serial configuration, GPIB address and user's IDN message.* On board voltage regulator for operation from 5 to 15 Vdc power.* Rear panel mounting eliminates cables.
-
product
USRP-2940, 50 MHz to 2.2 GHz, Reconfigurable USRP Software Defined Radio Device
783146-01
50 MHz to 2.2 GHz, Reconfigurable USRP Software Defined Radio Device - The USRP-2940 provides an integrated hardware and software solution for rapidly prototyping high-performance wireless communication systems. Built on the LabVIEW reconfigurable I/O (RIO) architecture, USRP RIO delivers an integrated hardware and software solution, so researchers can prototype faster and significantly shorten time to results. You can prototype a wide range of advanced research applications that include multiple input, multiple output (MIMO); synchronization of heterogeneous networks; LTE relaying; RF compressive sampling; spectrum sensing; cognitive radio; beamforming; and direction finding.
-
product
Simulator / Analyzer / Tester PCI BUS Interface Card
CIC301 - MIL-STD-1553
The CIC301 is a full-featured, high performance, Dual Redundant MIL-STD-1553 A/B serial bus Simulator Analyzer Tester designed as a plug in card for PCI backplane. The CIC301 includes full error injection and can operate in independent or simultaneous mode as a Bus Controller, multiple simulated Remote Terminals and full/selective Monitor. Its data structure can be changed on the fly without interrupting the processor for real time operation. The active monitor stores, time tag and annotates bus traffic with the message type and any detected errors. Stored words are annotated with a break down of the word error.
-
product
PCI-5114 , 125 MHz Bandwidth, 2-Channel, 8-Bit PCI Oscilloscope Device, 8 MB
779745-01
125 MHz Bandwidth, 2-Channel, 8-Bit PCI Oscilloscope Device—The PCI‑5114 low-cost oscilloscope device has two channels that sample up to 250 MS/s with flexible settings for coupling, impedance, voltage range, and filtering. Oscilloscope devices also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with fast signals that require flexible measurement configurations and up to 125 MHz of analog bandwidth.
-
product
USB-5133 , Oscilloscope 50 MHz Bandwidth, 100 MS/s, 2-Channel, 8-Bit USB Oscilloscope Device
780469-02
50 MHz Bandwidth, 100 MS/s, 2-Channel, 8-Bit USB Oscilloscope Device - The USB‑5133 low-cost oscilloscope device has two channels that sample up to 100 MS/s with flexible settings for coupling, impedance, voltage range, and filtering. Oscilloscope devices also feature a number of triggering modes and an instrument driver that includes data streaming and analysis functions. This device is ideal for portable and benchtop applications with fast signals that require flexible measurement configurations and up to 50 MHz of analog bandwidth.
-
product
PCI-6110, 4 AI (12-Bit, 5 MS/s/ch), 2 AO, 8 DIO, PCI Multifunction I/O Device Multifunction I/O Device
777475-01
4 AI (12-Bit, 5 MS/s/ch), 2 AO, 8 DIO, PCI Multifunction I/O Device - The PCI‑6110 is a simultaneous-sampling, multifunction DAQ device. It offers analog I/O, digital I/O, two 24‑bit counters, and digital triggering. The PCI‑6110 is ideal for a variety of applications, such as stimulus/response applications that require synchronization among analog input (AI), analog output (AO), and digital I/O. It is also ideal for 42 V automotive applications, radar, sonar, and ultrasound. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements. The PCI‑6110 dimensions require chassis slots that can accommodate full-length PCI modules.
-
product
Interface Converter
ZET 7176
Interface converter Ethernet/Wi-Fi↔CAN ZET 7176 is used for connection of CAN interface instrument communications nets based on digital transducers to PC over Wi-Fi or Ethernet. Wi-Fi or Ethernet network throughput rate allows to immediately fulfill commands and transmit great scope of data. Shared use of ZET7176 and ZET 7172 interface converters allows arranging instrument communications nets with radio linked transmission interface.
-
product
NI-9860, 2-Port, C Series Vehicle Multiprotocol Interface Module
783703-01
2-Port, C Series Vehicle Multiprotocol Interface Module—The NI‑9860 is a hardware-selectable HS/FD controller area network (CAN) and/or local interconnect network (LIN) interface for developing CAN and/or LIN applications. As part of the NI‑XNET platform, the NI‑9860 works well for applications requiring high-speed manipulation of hundreds of frames and signals while taking other data acquisition measurements in the same CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same CompactRIO chassis.
-
product
Test & Simulation Interface for PCI Express
PCIe-C1760
Avionics Interface Technologies
HS1760/MIL-STD-1760E Test & Simulation Interface for PCI Express
-
product
CPS-8910 , Switch Device for PCI Express
784307-01
PCI Express, Cabled Switch Device—The CPS‑8910 is designed for large multiple-input, multiple output (MIMO) expansion configurations and system control on the PXI platform or software defined radio devices. The CPS‑8910 provides two PCI Express upstream ports and eight downstream ports for seamless system expansion. You can connect the downstream ports to external devices, such as a Software Defined Radio Reconfigurable Device, to create large multichannel MIMO systems. You also can connect multiple CPS‑8910 switch boxes to a single PXI Express chassis to create massive MIMO systems with a Software Defined Radio Reconfigurable Device. The large data throughput capacity makes the CPS‑8910 an ideal data aggregator for massive MIMO systems. You can use the CPS‑8910 with copper or fiber-optic cables.
-
-
product
DSP, Mixers & Network Interfaces
Analog or digital, our line of mixers and interfaces help you effectively manage multi-microphone installations in boardrooms, city halls, conference spaces and distance learning environments.
-
product
*PC Interfaces
Ophir PC interfaces work on the smart plug principle. This means that almost any Ophir PC interface can work – plug and play – with almost any of the wide range of Ophir sensors. Ophir PC interfaces are also the most precisely calibrated units on the marketת, thus measuring with the highest accuracy. With the versatile Ophir StarLab software, your PC becomes a complete laser measurement station. Ophir also provides software to interface seamlessly with LabVIEW or the user's own software.
-
product
PCIe-1477, 80-Bit Camera Link, PoCL-Compatible Frame Grabber Reconfigurable Device
786502-01
The PCIe-1477 works well for deployment systems and features a user-programmable FPGA for onboard image processing. Placed directly in the image path, FPGAs can acquire and process images with closed-loop control without CPU intervention. This technology is also suitable for high-throughput system architectures to preprocess image data on the FPGA and then send the data to the CPU for further processing and decision-making. The PCIe-1477 also supports Power over Camera Link (PoCL), which you can use to power cameras through PoCL-enabled cables.
-
product
Avionics Interfaces & Test Instruments
ARINC 664
Avionics Interface Technologies
AIT’s ARINC 664 test instruments can be used in test and simulation applications that are required to transmit and receive data over the ARINC 664 avionics databus. AIT’s instruments use small form-factor pluggable transceivers (SFP) and support copper or fiber optic physical network interfaces.Using an FPGA based architecture, with multiple embedded processors, the ARINC 664 instruments provide onboard support for upper layer protocol processing (A653, UDP, IP) and utilize DMA to provide optimal data throughput. All ARINC 664 protocol operations, including VL traffic shaping, redundancy management, and IP fragmentation and reassembly, are handled onboard.
-
product
Gas Measurement Device
Gascoseeker 2-500
Teledyne Gas & Flame Detection
Built on the success of the robust and reliable Gascoseeker MK2, the Gascoseeker 2-500 is the UK gas industry standard instrument for measuring % LEL and % volume flammable hydrocarbons, with over 20,000 instruments in use in the UK gas industry.The two-button operation means the Gascoseeker 2-500 is easy to use and operator training can be conducted quickly. The rugged design allows the Gascoseeker 2-500 to be used in harsh environments. The Gascoseeker 2-500 is also fully compatible with our range of calibration software and equipment.
-
product
Isolated Interfaces
Isolate high-speed digital signals with ST's robust, reliable and flexible digital isolated interfaces.
-
product
8 GHz Differential Probe with ProBus2 Interface
DH08-PB2
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
product
Software to Simulate Large Area Semiconductor Devices
Laoss
Laoss is a powerful software to simulate large area semiconductor devices (OLED, thin-film PV), taking into account the voltage drop in the electrodes due to important resistive effects when the size of the device increases.Simulation of large area semiconductor devices (OLED, thin-film PV)Coupling law input: analytical or tabulated (experimental or simulated) IV curveDevice optimization (electrode material, device geometry etc...)High speed computation
-
product
Interface Adapter. USB Solution
U2C-11
Dimax USB to I2C Bridge device - U2C-11 converts USB transactions to I2C Master transactions. U2C-11 turns your PC running Windows or Linux OS into comprehensive I2C Bus master.
-
product
Interface Module for the Multimode, Muliprotocol Excalibur 8000 Family Carrier Boards
M8K1553MCH
The M8K1553MCH interface module for the multimode, multiprotocol, Excalibur 8000 family of carrier boards provide a complete solution for developing and testing 1553 interfaces and performing system simulation of the MIL-STD-1553 bus. The module handles all standard variations of the MIL-STD-1553 protocol.The M8K1553MCH contains 32k x 16 of dual-port RAM for Data blocks, Control registers, and Look-up tables. All Data blocks and Control registers are memorymapped and may be accessed in real time. The dual-redundant 1553 module may be programmed to operate in one of four modes of operation: Bus Controller, Remote Terminal, RT/Concurrent-Bus Monitor, and Bus Monitor. The M8K1553MCH comes complete with Windows software, and a C driver software library including source code.
-
product
3U cPCI Sensor Interface Unit
SIU33
NAI's SIU33 is a highly configurable rugged COTS system or subsystem ideally suited for rugged military, industrial, and commercial applications that require high-density I/O, communications, Ethernet switching, and processing. The SIU33 uses up three NAI field-proven, 3U cPCI boards to deliver off-the-shelf, SWaP-optimized COTS solutions that "Accelerate Your-Time-to-Mission."
-
product
Separation Layer Device
NivuScope 2
NivuScope 2 measurement system for reliable separation layer detection and sludge level measurement mainly in primary and secondary clarifiers
-
product
Power Transformer Automatic Test Device
XD71
Hangzhou Xihu Electronic Institute
The device is used for power transformer power outage routine test items to do automated testing.Which is characterized by dielectric loss, insulation resistance, DC resistance, tap-changer switching characteristics, short circuit impedance and variable ratio of six test items are concentrated in an instrument,so that the instrument function, test power and test lead height fusion.Field test, just start wiring once, at the end of unplugging wiring once,the middle process by the test personnel in the computer terminal to send command control,the test system automatically completes all or part of the above test items.
-
product
USB-7855, Kintex-7 70T FPGA, 1 MS/s Multifunction Reconfigurable I/O Device
782915-01
Kintex-7 70T FPGA, 1 MS/s Multifunction Reconfigurable I/O Device - The USB‑7855 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The USB‑7855 features a dedicated A/D converter per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical DAQ hardware.
-
product
Proving Devices
Martindale Electric Proving Devices - safely prove the operation of voltage indicators and test lamps
-
product
PCI-5421, 100 MS/s, 16-Bit Waveform Generator Device
778692-02
The PCI‑5421 can generate user-defined, arbitrary waveforms and standard functions, including sine, square, triangle, and ramp. This arbitrary waveform generator can generate signals from -6 V to +6 V and uses direct digital synthesis (DDS) to precisely generate waveforms. The PCI‑5421 also features advanced synchronization and data streaming capabilities.
-
product
ICD 3 Test Interface Module
AC164113
The Test Interface Board is an aid to isolate application interfacing problems when using the MPLAB ICD 3 (DV164035) as a debugger or programmer. Using the Test Interface Board and running confidence-test options under MPLAB IDE allows testing of the basic functions and signals of an MPLAB ICD 3. The diagnostic results under MPLAB IDE let the user know when the MPLAB ICD 3 is fully functional or if there is a malfunction. The MPLAB Online Help shows the user how to determine possible causes of hardware communication failures with the application.
-
product
25 Pin Breakout Interface
VSI-Breakout-25
The VSI-Breakout-25 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
product
Power Device Analyzer / Curve Tracer
The B1505A Power Device Analyzer / Curve Tracer is focused on the needs of power device manufacturers, while the B1506A Power Device Analyzer for Circuit Design is focused on the needs of power electronics circuit / product manufacturers. The B1507A Power Device Capacitance Analyzer helps both power device development engineers and power circuit designers maximize product value by revealing device capacitance characteristics.
