Synchronization Modules
-
Product
LED Light Bar Module
UTC-100P-L
Module
Interface: USB (Cable Length:50cm). OS Support: Windows 10 & Android. Dimensions: 160.0 x 18.5 x 9.0 mm. Operating Temperature: 0 ~ 40° C.
-
Product
NI-9201 , ±10 V, 500 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module
779013-01
Module
±10 V, 500 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module - The NI‑9201 is an effective combination of channel count and speed at a low price for an economical multifunction system. The module features up to 100 V of overvoltage protection for errant signal connection or unexpected signals to the individual channels.
-
Product
H009 Module
M4KH009
Module
H009 modules can operate as a Central Computer Complex (CCC) and/or up to 16 Peripheral Units (PUs) simultaneously, or as a Bus Monitor. In addition, a Concurrent Bus Monitor enables concurrent monitoring of the bus during CCC and PU simulation. The module also supports error injection and detection, and all control parameters and data may be updated in real time. Note: The M4KH009 Module is a "double size" module, and occupies two vertically adjacent sockets in the EXC-4000 carrier Board.
-
Product
PXI Dual 2 x 2 Fibre Optic (M Mode) SC M50
40-860-222-M50
Switch Module
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
PXI High Density Multiplexer, 2-Bank, 40-Channel, 1-Pole
40-615A-017
Multiplexer Module
The 40-615A-017 is a 2-bank, 40-channel, 1-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. These feature a wide range of switching configurations and are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector.
-
Product
40 Channel Single-Ended Multiplexer Module for DAQ970A and DAQ973A
DAQM908A
Multiplexer Module
40 Channel Single-Ended Multiplexer Module for DAQ970A and DAQ973A. Single-wire switching for common low applications with scan speed of up to 80 ch/s.
-
Product
PXI/PXIe RF Multiplexer, Dual 8-Channel, 3GHz, 75Ω, MCX
42-834A-102
Multiplexer Module
The 40-834A-102 (PXI) and 42-834A-102 (PXIe) are 75 Ohm 8 to 1 RF multiplexers with 2 banks in a single slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The design of the 40/42-834A minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP4T, 67 GHz, 50 Ω, SMA-1.85, Terminated, Remote Mount, Failsafe
42-785C-472-TE
Multiplexer Module
The 40-785C-472-TE (PXI) and 42-785C-472-TE (PXIe) are dual failsafe SP4T 67 GHz with automatic termination of unused signals and remotely mounted relays. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
Product
PXI/PXIe High Density 2A Multiplexer, 16-Bank, 4-Channel, 2-Pole
40-614D-002
Multiplexer Module
The 40-614D-002 (PXI) and 42-614D-002 (PXIe) 16-bank, 4-channel, 2-pole multiplexers are part of the High Density 2Amultiplexer module range available in 22 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PXI/PXIe MEMS Optical Switch, Dual Insert/Bypass
40-860A-522-M
Multiplexer Module
The 40/42-860A-522-M is a PXI/PXIe dual insert/bypass switch with ST connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
Product
PXI Triple SP4T Multiplexer 6GHz 50 SMA
40-784A-103
Multiplexer Module
Pickering Interfaces’ range of 40-784A PXI Microwave Multiplexer Modules have a characteristic impedance of 50Ω and are capable of switching signals up to 40GHz. Available in single, dual or triple, SP6T or SP4T formats, they are suitable for constructing complex microwave switching networks and provide a range of switching configurations to suit most applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors
-
Product
PXI/PXIe Microwave Multiplexer, Single SP4T, 40GHz, 50Ω, SMA-2.9
40-784B-141
Multiplexer Module
The 40-784B-141 (PXI) and 42-784B-141 (PXIe) are single SP4T 40GHz unterminated microwave multiplexers. The 40/42-784B range is available with single, dual or triple, SP6T or SP4T multiplexers with front panel mounted or remotely mounted relays.
-
Product
PXI/PXIe MEMS Optical MUX, Dual 2-Channel, Single-Mode
40-855A-122
Multiplexer Module
The 40/42-855A-122 is a PXI/PXIe dual 2-channel multiplexer with FC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP6T, 40GHz, 50Ω, SMA-2.9, Remote Mount
40-784B-042-E
Multiplexer Module
The 40-784B-042-E (PXI) and 42-784B-042-E (PXIe) are dual SP6T 40GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-784B range is available with single, dual or triple, SP6T or SP4T multiplexers with front panel mounted or remotely mounted relays.
-
Product
PXI/PXIe Microwave Transfer Switch, Dual, 18 GHz, 50 Ω, SMA, Failsafe, Remote Mount
42-782B-522-E
Switch Module
The 40-782B-522-E (PXI) and 42-782B-522-E (PXIe) dual failsafe transfer switches with remotely mounted relays are part of our range of PXI microwave switching modules. They have a characteristic impedance of 50 Ω and a maximum operating frequency of 18 GHz. Connections are made via front panel mounted high quality SMA coaxial connectors.
-
Product
PXIe-5663E, 6.6 GHz PXI Vector Signal Analyzer
781259-02
Signal Module
6.6 GHz PXI Vector Signal Analyzer - The PXIe‑5663E offers wide instantaneous bandwidth and supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. You can use a PXIe‑5663E as either a spectrum analyzer or vector signal analyzer, and you can use it with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5663E can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5663E provides a low-cost solution to high-performance RF measurements.The PXIe-5663E comprises the following modules:• PXIe-5601 RF Signal Downconverter• PXIe-5622 IF Digitizer• PXIe-5652 RF Analog Signal GeneratorThere is no physical device named "PXIe-5663E".
-
Product
ARINC-708/453 2-Channel Test & Simulation Module for the Weather Radar Display Databus
M8K708
Test Module
The M8K708 module is an ARINC-708 / 453 2-channel test and simulation module for the Weather Radar Display Databus. The M8K708 supports two ARINC-708 / 453 channels, each selectable as transmit or receive. Each channel implements an 64K×16 FIFO and supports polling and/or interrupt driven operation.The M8K708 comes complete with Windows software, a C-driver software library including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application. In addition, Excalibur produces adapter cables that convert the carrier board I/O Molex™ connector to two twinax CJ70-49 connectors. The cable may be purchased at an additional cost.
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP4T, 50GHz, 50Ω, SMA-2.4
40-785C-452-TE
Multiplexer Module
The 40-785C-452-TE (PXI) and 42-785C-452-TE (PXIe) are dual SP4T 50GHz microwave multiplexers with automatic termination of unused signals and remotely mounted relays. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
Module, Receiver, RTCASS, Signal, 210 Position, Discrete Wiring
510113146
Receiver Module
Module, Receiver, RTCASS, Signal, 210 Position, Discrete Wiring.
-
Product
PXI Very High Density MUX 49 Chan 4 Pole
40-675-002-49/4
Multiplexer Module
The 40-675 series of very high density low cost multiplexer modules are available in a versatile range of switching configurations. The modules are supplied pre-configured in one of six multiplexer modes suitable for signal routing in high channel count ATE and data acquisition systems. The modules use high quality electromechanical signal relays allowing each channel to switch current up to 1A at 150VDC/100VAC. Connections are made via a front panel 200-pin connector.
-
Product
PXI/PXIe MEMS Optical Switch, Quad Insert/Bypass, Single-Mode, 9/125 Fiber, MU Connectors
42-860A-342
Switch Module
The 40/42-860A-342 is a PXI/PXIe quad insert/bypass switch with MU connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
Product
LXI High Voltage Switching
65-233-902-HI
Switch Module
The 65-233-902-HI plug-in module is part of a scalable high voltage switch platform that provides a high voltage switching solution with capability up to 9 kV.
-
Product
QSeven
ROM-7420
Computer-on-Module
ROM-7420 Qseven Module integrates an ARM Cortex-A9 NXP i.MX6 series ultra low power SoC and I/O solution chips with Linux. NXP i.MX6 supports 2D, 3D graphicsacceleration, full HD 1080P video decoding and an HD 1080p video encoding hardware engine.
-
Product
LXI Microwave Multiplexer, 50Ω 4-Channel 15-Bank 40GHz SMA-2.9
60-802-415
Multiplexer Module
The 60-802-415 is a 4-channel, 15-bank RF multiplexer suitable for switching 50Ω signals up to 40GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
LXI Dual 4:1 Optical MUX SC Multi-Mode
60-851-209
Multiplexer Module
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
Product
PXI Solid State Switch Module, 6xSPST, 10 A
40-182A-011
Switch Module
The 40-182A-011 has 6 off high current SPST switches in two PXI slots and is part of our range of high power solid state switching solutions. Each SPST switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each SPST switch can support 10A of continuous current and switch up to 200V signals. The switch can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
PXI/PXIe High Density 2A Multiplexer, 10-Bank, 4-Channel, 3-Pole
42-614D-022
Multiplexer Module
The 40-614D-022 (PXI) and 42-614D-022 (PXIe) 10-bank, 4-channel, 3-pole multiplexers are part of the High Density 2A multiplexer module range available in 23 configurations (see 'Also in this Range' link above).
-
Product
SIM, Module, Receiver, 90 Series, Fully Loaded with pairs of VTAC Standard Pass-Thru and Right Angle Inserts (610151106)
510170102
Receiver Module
This fully loaded SIM module kit comes with 34 pairs of VTAC Standard Pass-Thru and Right Angle Inserts (610151106). This kit also includes two PCB brackets for securing module to PCB.
-
Product
PXI Prototyping Module, 1-Slot, 9-Pin D-Type
40-225A-701
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
PXIe-5663E, 6.6 GHz PXI Vector Signal Analyzer
781259-01
Signal Module
6.6 GHz PXI Vector Signal Analyzer - The PXIe‑5663E offers wide instantaneous bandwidth and supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. You can use a PXIe‑5663E as either a spectrum analyzer or vector signal analyzer, and you can use it with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5663E can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5663E provides a low-cost solution to high-performance RF measurements.The PXIe-5663E comprises the following modules:• PXIe-5601 RF Signal Downconverter• PXIe-5622 IF Digitizer• PXIe-5652 RF Analog Signal GeneratorThere is no physical device named "PXIe-5663E".
