Programmable Loads
-
Product
Programmable Ammeter
IM1953
-
Programmable Digital Ammeters are DC current indicators with High and Low alarm limits. Also known as AC Ammeter, Electronic Ammeter, etc.
-
Product
Partial Load Failure
PLF Device
-
The control device series “PLF” has been designed to monitor the partial and/ or total failure of the alternating current absorbed by loads driven by static switches and / or electromechanical relays.
-
Product
Programmer
TurboProg
-
TURBO-PROG supports two types of turbo actuators:*Hella actuators with the following markings:712120, 730314, 781751, 763797*Siemens actuators in a metal-plastic housing used in turbochargers made for VW/Audi with 2.7TDI and 3.0TDI engines.
-
-
Product
In-System Programmer for ARM
MPQ-ARM
-
Supports Nuvoton M05x and NUC1xx device families Field Upgradeable - always supporting the latest devices Secure image management - protects your IP In-circuit gang programming of up to four devices at once Can be deployed in arrays to program up to 64 devices in parallel Stand-alone, PC-controlled or ATE-controlled operation Automatic device serialization
-
Product
Load Banks
EL08 Series
-
*Rectifier Test 8kW*All of our Load Banks are continuously rated for Power and Current.
-
Product
Unclamped Inductive Load Tester
ITC75300
-
The ITC75300 is a 400 amp version of the ITC75100 which performs ruggedness testing of power MOSFET’s, IGBT’s and diodes that conforms to MIL-STD-750 method 3470 by stressing them to controlled energy levels, accomplished by the devices driving an unclamped inductive load. Improved Test Specifications allow complete control of test parameters.
-
Product
PCI Precision Resistor Card 9-Channel, 2Ω To 26.7kΩ
50-297-032
-
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Hand-Held/Digital Load Tester
6030DV
-
• Full 125 Amp load Tests 12 Volt and 24 Volt batteries (DUAL LOAD) alternators and starters on all types of vehicles• PATENTED• Made in USA of US and Global Components
-
Product
Universal Programmable Transmitters
-
Omega offers a large selection of programmable universal transmitters that accept universal inputs including mA and Vdc process signals and all commonly used temperature signal types.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-044-HI
-
The 40-230-044-HI (PXI) and 42-230-044-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4Ω and 1.5MΩ with 2Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
JD Edwards Load Testing
Dimension LoadTest
-
Dimension LoadTest™ is a powerful yet easy to use load testing tool for JD Edwards EnterpriseOne applications. DWS have designed Dimension LoadTest such that any experienced System Administrator/CNC should be able to setup, create, run and monitor load tests to effectively stress test JD Edwards EnterpriseOne applications.
-
Product
Low Profile Compression Only Load Button Load Cell with Mounting Holes
LBC SERIES
-
The LBC Series (Load Button) load cells are offered for compression only applications where space is limited. The matching surface must be flat and at least the diameter of (D1). The loading diameter (D2) is slightly convex for accurate load distribution. Counter bored mounting holes are provided for fastening down from the top. These sensors are manufactured from heat treated 17-4ph stainless steel and sealed for use in most industrial environments.
-
Product
Load Banks
PARELO
-
Amfax introduce the latest generation of load banks we affectionately call PARELO. This range of load banks provides a combination of high performance passive resistive loads along with extreme flexibility of use. This is achieved by our unique FLEXI-phase Switching(TM) technology.. Designed primarily for offering high wattage loads for the aerospace, energy, automotive and transport sectors. PARELO load banks are a cost effective solution for companies requiring high wattage loads when testing their products.
-
Product
Programmable Linear DC Power Supply
MPS-S Series
-
Triple channel programmable DC power supply is with high resolution, high precision and high stability, over-voltage and over-heat protection are available. Series and parallel operation are also provided. The resolution is 10 mV/1 mA.
-
Product
PCI High Density Pecision Resistor Card, 4-Channel, 3Ω To 52.4kΩ
50-298-133
-
The 50-298-133 is a high density programmable resistor card with 4 channels which can be set between 3Ω and 52.4kΩ with 1Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Digital Load Cell Simulator
Model EL41
-
Xiamen Elane Electronics Company, Ltd
Detection and debugging of all kinds of weighing instruments - "must have" for any scale service technician - fully RS232 controllable for testing of electronics for scale installation and manufacturing.
-
Product
PCI High Density Potentiometer Card 2-Channel, 12-Bit, 0 To 4k Ohm
50-296A-021-2/12
-
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Load Cells, Weighing and Force Sensors
-
We are pleased to offer Load Cells from both Zemic and Vishay. We are the exclusive UK distributor for Zemic load cells.
-
Product
High Voltage DC Electronic Load
3360F Series（600W~14.4KW）
-
3360F has its own control and display panel, CC/CR/CV/CP/Dynamic modes, 150 sets Store/Recall memory which provides load set-up more efficiently, also can be remote controlled via GPIB, RS232,USB and LAN interface.
-
Product
DC Electronic Loads
LSG Series
-
*Operating Mode : C.V/C.C/C.R/C.P/C.C +C.V/C.R + C.V/C.P. + C.C.*High Precision, High Resolution (10 A),High Speed Variable Slew Rate (16A/ s).*Sequence Function for High Efficient Load Simulations.*Parallel Connection of Inputs for Higher Capacity. (With 4 Booster Units : Max 9.45kW or 4 Master Units)*External Channel Control/Monitoring via Analog Control Connector.*Program Mode to Create Work Routines for Repetitive Tests.*Multiple-Interface : USB 2.0 Device/Host and GPIB/RS-232C.*Adjustable OPP/OCP/OVP Setting.
-
Product
PXI Resistor Module 2-Channel 1.5R to 8.19k with SPDT
40-293-124
-
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Dynamic Mechanic Loading Tester
-
King Design Industrial Co., Ltd.
*Complies with IEC 61646, IEC 61215 mechanical load test specification. * Air pressure is adjustable, output range is from 2400pa to 5400pa ±5% . * Maximum measurement range: 220 x 260 cm. * Apparatus structure material：aluminum-extruded. * Fixtures and holders can be customized design for requirement of testing module. * Manual operation is simple; manual maintenance is easy.
-
Product
0-5kv Programmable AC Hipot Insulation Tester
7112
-
Shenzhen Chuangxin Instruments Co., Ltd.
Programmable AC withstand voltage insulation tester Feature: Small volume, light weight Easy to operate, has keyboard lock function
-
Product
DC Electronic Load
3310G Series（800W）
-
Has its own control and display panel, CC / CR / CV / CP / Dynamic modes, with 150 sets Store / Recall memory which provides load set-up more efficiently, also can be controlled via RS232、Ethernet、USB and GPIB interface
-
Product
VME Load Card
-
WIENER VME load boards are designed to test VME crate power supplies and fan trays by drawing power from the VME backplane and dissipating it as heat. A series of switches on the module front panel allows for easy adjustment of the current draw for each voltage channel.
-
Product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 255 Ohm
40-294-013
-
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Thermal Load Boards
-
Thermal Engineering Associates, Inc.
A Thermal Load Board (TLB) is used to simulate an application printed circuit assembly (PCA) either before all the heat-producing components are available for mounting on the application PCA or if the heat-producing components require complex electronic circuitry to create heat within the components. The TLB is typically designed to be as mechanically and thermally equivalent to the application PCA and usually offers a way to vary the power dissipation of the elements that simulate the heat-producing components.
-
Product
Mini Low Profile Load Cell Universal/ Tension or Compression
MLP SERIES
-
The model MLP Series load cells were designed with economy as first priority. They are a scaled down version of our successful LPO Series Load Cells. MLP-10 through MLP-300 are anodized aluminum and the MLP-500 through MLP-1K are made from 17-4ph heat treated stainless steel. The unique low profile design of the MLP Series provides excellent stability for in line applications for tension and/or compression, while saving space at the same time.
-
Product
RF and Microwave USB Programmable Signal Generators
LSG Series
-
The Lab Brick LSG series of low cost USB-compatible RF and microwave signal generators covers frequencies from 20 MHz to 6 GHz with high output levels and excellent spectral purity. They require no additional DC supply voltage and offer several operating modes, including continuous-wave (CW) and swept-frequency. GUI software can track and control several connected signal generators, simplifying multiple-signal test setups. Each device stores settings in internal memory, allowing it to power up in a specific instrument state.
