Impedance Testers
See Also: Loop Impedance Test, Impedance Analyzers
-
product
Impedance Analyzer
6632
Frequency range: DC, 10Hz to 1/3/5/10/20/30MHz/50MHz. Basic accuracy up to ±0.08%. Automatic Level Control (ALC). Output impedance 25Ω/100Ω, switchable. Equivalent Circuit Analysis . Built-in DC Bias voltage ±12V. Ultra-high measuring speed < 3ms. Built-in the Dielectric constant-εr. Built-in the Permeability-μr. Support PC Link Software.
-
product
Antenna Impedance Converter
The low noise impedance matching equipment has a high impedance input with minimized capacity. With the 50 Ω output it can be used with common EMI receivers or spectrum analyzers to measure the emissions received by an antenna on a vehicle.
-
product
Capacitor Tester
MIG0603CAP
The MIG0603CAP consists of two circuits with impulse capacitance 20 µF and 0,25 µF. Both circuits generate a voltage wave shape 1,2/50 µs and are combined in a 4 unit height 19" rack. The generator circuits are defined in IEC 60384-14 and EN 132400. The serial resistors Rs, the impulse capacitor CT, and the load capacitance Cp will be automatically switched when different capacitance ranges are selected on the MIG0603CAP.
-
product
Voltage Tester
HH2611
Handy, quick response and easy to use tool. Safe to use Non-Contact testing 90-220V AC voltage. Delect AC voltage without connecting into the wire circuit. Very bright LED and buzz sound alarm if voltage is present. Used to detect where the wire is broken. Used to detect whether an outlet is present of voltage. Used to detect a broken Christmas bulb out of a series of connected Christmas bulbs
-
product
Epstein Tester
S21 and S21R Series
Incoming material inspection can be very useful where strict quality standards are maintained. It saves a lot of processing cost since lossy material is inspected at the entry level before it goes to production level. Epstein Stack testing is one of the oldest and widely used methods for electrical sheet testing.
-
-
product
Transformer Testers
*Quickly tests deenergized power distribution transformers*Briefly energizes the transformer and takes a snapshot of the condition by measuring the voltage, current and power factor of the test signal*Tests overhead, pad-mount and distribution transformers*Audible alarm confirms successful test*Improve SAIDI statistics by quickly testing and getting the transformer back in service*Auto self-test performed with every test*Compact, lightweight and easy-to-use
-
product
5uH Line Impedance Stabilisation Network LISN - CISPR 25
TBOH01
The TBOH01 5H LISN is a device required to setup conducted noise measurements of DC-powered devices. It is designed to be used for EMC pre-testing in the frequency range of 150kHz to 110 MHz.
-
product
Scratch Tester
CSR1000
This tester is highly effective in measuring the adhesion strength (adhesion strength) of hard coatings (Ti, TiN, SiC, DLC, etc.) formed by PVD and CVD on metal surfaces such as cemented carbide. Adopting a scratch test method that allows quantitative measurement with simple operations, the film surface is scratched while increasing the load on the sample surface, detecting film breakage with high sensitivity, and providing the load at which film breakage occurs (critical load). tools and mold tools that require
-
product
Puncture Testers
Mechanical puncture testers check the puncture resistance or hardness of materials like dry wall, foam boards, cardboard, etc. They are ideal for handheld penetration tests or mounting to a test stand and intrinsically safe in hazardous environments. An optional handle is available.
-
product
Vector Tester
PVT360A
The R&S®PVT360A is a VSG/VSA single-box vector tester optimized for FR1 base station, small cell and RFcomponent testing in production and characterization environments. Two independent signal generatorsand analyzers enable fast parallelized measurements. A frequency range of up to 8 GHz, flexible bandwidth configuration and an optional second TRX channel provide the necessary performance and enable flexible adaptation in a small form factor.
-
product
Torque Tester
WDIS series
Management of various torque tools PLC and connection alsoWDIS-IP (05/5/50/200/500/1500), WDIS-RL (005/05/6/10), WDIS-IPS (05C/5C/20CL). The DIS series has become easier to use and has higher performance. Interlocking with a personal computer or PLC, the torque measurement can be managed at a higher level.Management of manual torque drivers and wrenches, management of automatic and semi-automatic tools, inspection of screw tightening and loosening torques
-
product
Rotor Tester
SL Series
Shanghai Aoboor Electric Co., Ltd.
Applicable for testing fully opened, fully closed squirrl-cage rotors with process slot, with or without shaft, it can identify broken bars, slim bars, under-casting, porosity, sand holes, residues, improper end rings, internal short circut in bars, eccentricity.
-
product
Precision Impedance Meter
1689
The GenRad 1689 Precision Impedance Meter gives you the best performance for your most demanding applications whether they be production test, incoming inspection, component design and evaluation, process monitoring or dielectric measurement. It is a versatile, full function microprocessor-based passive component tester that's available in a rack mountable, (1689M) model.
-
product
Circuit Tester
TE6-0720
Hangzhou Tonny Electric & Tools Co., Ltd.
*For use on cars, trucks, boats, trailers and motorcycles*Needle point probes *Use to trouble shoot both primary and secondary circuits*Use this tester to check primary circuits of 6/12V*On secondary or high voltage circuits you can check spark plugs
-
product
Alternator Tester
ALTALYZER Tester
The Altalyzer tester is used to check the correct operation of alternators equipped with electronically controlled voltage regulators. In alternators of this type, the charging voltage is not constant, but varies depending on external factors such as: engine revolutions, number of current receivers, etc. The voltage at a given moment is determined by the motor controller by sending the appropriate information to the alternator.
-
product
Hardness Tester
JINAN PRCISION TESTING EQUIPMENT CO., LTD
Hardness testing is measuring a material's resistance to permanent deformation at its surface
-
product
GAS Testers
Shenzhen Noyafa Electronic CO.,LTD
Noyafa GAS Tester uses high-quality semiconductor sensors, which can effectively eliminate interference and accurately obtain the concentration of formaldehyde, TVOC, etc. within the measurement range, accurate to the thousandth. With more than ten years of professional testing background, well-known big brands are more at ease and assured to use.
-
product
Hardness Testers
The hardness tester products you will find at PCE Instruments (PCE) are used for determining surface hardness. Each hardness tester uses a standard method of measurement. The measuring principles of most hardness tester devices are based on either the penetration of a diamond indentor into the material being tested or a calculation related to the force of the rebound after striking the tested material. However, material hardness can also be measured accurately through ultrasonic testing. Each hardness testing method has its benefits and will allow for the precise measurement of material hardness in accordance with the technical specifications of the hardness testing instrument.
-
product
Thickness Tester
CX-Series
The Thickness Tester - CX-1000 combines our patented capacitance sensor with industry-leading software to give you plastic film thickness profiling resolution to one micron. This gauge can be run as a stand-alone bench unit, or can be connected to a computer for RS-232 operation by our Thickness Tester - CX-1100 Quality Control Software. Capacitance measurement is industry-recognized as the best choice for off-line, high resolution, continuous gauge profiling for plastic films.
-
product
Precision Impedance Analyzer
TH2851-015
Changzhou Tonghui Electronic Co., Ltd.
■ Test frequency: 10Hz-15MHz ■ High precision: using automatic balance bridge technology, four-terminal pair test configuration
-
product
Wire Testers
Precision Mastech Enterprises Co.
ower supply: 1*9V 6F22 BatteryProduct size: 190mm*89mm*42.5mm/7.48"*3.5"*1.67"Product weight: 420g/0.92IbSafety rating: CE(EMC+LVD) ETL CAT.III 300V RoHS
-
product
Tensile Tester
Wewon Environmental Chambers Co, Ltd.
Is a fundamental materials science test in which a sample is subjected to a controlled tension until failure
-
product
Impedance Analyzers
1MHz to 300MHz Measurement Frequency Impedance Analyzer with 0.5ms Test Speed and Superior Repeatability
-
product
Sensor Tester
QST-5
The QST-5 device is intended for testing many popular sensors used in the automotive industry. The tester powers the tested sensors by itself, so it can be used both in a vehicle and outside of it.
-
product
Network Tester
ZhangZhou Weihua Electronic co.,ltd
There is nothing worse than running your drops only to learn that you have a fault in one of the cable runs. Get it right the first time, get it right by choosing and using the right LAN Cable Testers. We offer a variety of cable testers, which are a must have to quickly and easily verify the integrity of Ethernet twisted pair cables. Our LAN testers will test twisted pair cables for open pairs, shorted pairs, reversed pairs, crossed pairs and split pairs. Network cable testers vary in complexity and price, but a basic tester consists of a source of electrical current and a measuring device. After that, cable testers vary in complexity and ability to do various testing.
-
product
EMI Tester
The EMI tester automatically measures the noise distribution of the electric field and the magnetic field radiated from electronic equipment with high accuracy.・ Even if PCB and IC parts have complicated bumpy shape and surface. The movable assembly can automatically trace them.・ EMI noise distribution is expressed as a variety of maps, such as 4D/3D/2D graphics and cross section view.
-
product
Battery Tester
IT5100 Series
IT5100 series is a series of battery internal resistance testers with high precision, high resolution and high speed. IT5100 adopts AC 4-terminal sensing, that means the tester can test internal resistance and voltage simultaneously with high precision. Resistance resolution is down to 0.1 μΩ, voltage resolution is 10 μV.
-
product
Defibrillator Analyzers, Pacemaker Testers and AED Testers
Fluke Biomedical’s defibrillator analyzers and defibrillator/transcutaneous pacemaker testing devices are rugged, portable precision test instruments that ensure proper operation and ultimate performance of critical life-support cardiac-resuscitation equipment. We offer best-in-class defibrillator testers that feature capabilities which encompass a wide spectrum of worldwide established pulse shapes, showcasing AED tester compatibility, and outperforming competitors in accuracy and standards.
-
product
Insulation Tester
AD-225
3 Measurement voltage range: 500 V; 1000 V and 2500 V, Control of measuring voltage during measurement, Insulation measurement up to 100 G W, Elimination of trough resistance insulation ? 3 connectors measurement method, Autoranging,
