Simulators
create what could be.
See Also: Simulation, Simulation Software, Simulation Testing, Emulators
-
Product
GPS/GNSS Antenna Signal Splitter 4-Way, TNC Female, IP67 Weatherproof, 1-2 GHz
GPS421
-
INSTOCK Wireless Components, Inc
GPS421 is a four way, passive, GPS signal splitter ideal for splitting a GPS antenna signal between two receivers while providing a DC current path to power a remotely located active GPS antenna from one receiver while blocking the DC path from the other. Furnished with TNC female connectors all ports. A special feature of this unit is the 200 ohm internal load which provides a current drain for the GPS receiver not powering the active antenna. Some GPS receivers incorrectly sense an antenna fault when there is no current draw. The 200 ohm internal load provides a simulated antenna current drain which prevents receiver faulting. Max voltage rating at the DC blocked ports is 15 VDC; maximum current rating is 75 mA. Max voltage rating at the DC pass port is 50 VDC; max current rating is 2000 mA.
-
Product
Simulation Table
KRD61 6-DOF
-
KRD61 series 6-DOF simulation table is a closed-loop servo simulation platform consisting of six servo actuators and six sets of dedicated hinges connected at the top and bottom platforms respectively. By virtue of the telescopic movement of the six actuators, the upper platform moves in six degrees of freedom (X, Y, Z, α, β, γ), so various space motion attitudes can be simulated.
-
Product
PXIe Battery Simulator Module, 4-Channel, 5 Amp
43-754-011
-
The 41-754-011 and 43-754-011 are 4 channel battery simulators, capable of supplying up to 8 V and 5 A per channel. The channels are fully isolated from ground and from each other allowing series connection to simulate batteries in a stacked architecture. The isolation barrier (1000 V channel to GND and 750 V channel to channel) allows the module to be used as a battery stack representative of those used for vehicle propulsion..
-
Product
Testing of Rear Axle Steering
-
*2 high-precision servo axes for linear load simulation*Communication via CAN / Flexray*Function and noise measurements (NVH)*Supply and discharge of the test specimens via WTs on double belt conveyors*Connection to the production control
-
Product
Voltage Variation Simulator
KES7400A
-
The KES7400A Series comes in a single cabinet that consists of a Signal Generator module (including an arbitrary pulse generator), which combines our power supply technology and EMC technology, and a high-speed bipolar power supply module. Many automotive electronic devices have long wire harnesses and inductive load characteristics, as do motors, or capacitive load characteristics with a large-capacity capacitor connected between the input and ground. In the case of these devices, general DC power supplies exceed the linear operation range, potentially making it impossible to obtain the desired waveform output.
-
Product
Bite Test Clamp
G201A29-30
-
Simulates a child biting the accessible area of child-related products. The part of the child-related products being tested is placed in a bite test clamp & a specified force is applied for a specified period. The child-related products is then tested to ascertain whether or not any hazards result from the bite test such as sharp points/sharp edges/small parts.
-
Product
Radiation Microdosimeters
-
Teledyne e2v HiRel Microdosimeter is a compact hybrid microcircuit which directly measures total ionizing dose (TID) absorbed by an internal silicon test mass. The test mass simulates silicon die of integrated circuits on-board a host spacecraft in critical mission payloads and subsystems. By accurately measuring the energy absorbed from electrons, protons, and gamma rays, an estimate of the dose absorbed by other electronic devices on the same vehicle can be made. The Microdosimeter can operate from a wide range of input voltages. The accumulated dose is presented to three dc linear outputs and one pseudo-logarithmic output giving a dose resolution of 14 µrads and a measurement range up to 40 krads. These outputs are intended to be directly connected to most analog-to-digital converters (ADCs) or spacecraft housekeeping analog inputs (0-5 V range), which makes minimal demands on the host vehicle. The Microdosimeter incorporates a test function to allow electrical testing of the hybrid without the need for a radiation source.
-
Product
BRI and PRI Simulator
emutel Ultra
-
emutel Ultra is a standalone or rackmount unit that comes in five variants giving 8 BRI, 2 PRI and 8 BRI, 2 PRI and 15 BRI, 8 BRI and 14 analogue or 2 PRI, 8BRI and 14 analogue. emutel Ultra can emulate different country specific networks by adding network personality cards & networks supported include North American, NTT, Euro-ISDN, VN3, ITR6 and BTNR191. Protocol analysis option is also available on emutel Ultra.
-
Product
Test And Simulation Devices
BreakingPoint
-
Control global threat intelligence at Internet-scale to create massive-scale, high fidelity simulation and testing conditions for battle-testing infrastructures, devices, applications, and people.
-
Product
PXI Data Communications Multiplexer
40-736-001
-
This Data Communications Multiplexer is designed specifically for multiplexing or de-multiplexing up to 32 differential signal pairs having controlled 100 differential impedance. The multiplexer can be configured under software control to provide switching for 32 differential pairs, 16 dual differential pairs and 8 quad differential pairs. The dual and quad versions are particular well suited for providing switching of AFDX, BroadR-Reach and Ethernet signals. To support Ethernet applications, the design includes a switching network that simplifies the swapping of Tx and Rx pairs to simulate the effect of Ethernet crossover cables.
-
Product
Equipment
-
Based on a proprietary light engine, our solar simulation equipment delivers perfect and continuous artificial sunlight 24/7, allowing for accurate stability and performance assessments of solar cells at laboratory and industrial scales.
-
Product
MIMIC® Cable Modem Simulator
-
MIMIC Cable Modem Simulator, is the industry's first integrated simulation tool supporting DOCSIS, allows cable modem developers and cable companies to perform real world, integrated cable and internetworking device simulations. MIMIC allows suppliers of cable modems to design, develop and test their products in a virtual and scalable network environment, assuring customers that their cable modems will work properly when deployed across heterogeneous environments. Cable providers can use MIMIC to simulate the 1000s of households that use cable modems to assure the scalability of cable management software. In addition, providers can also use MIMIC for large-scale Operations Support System (OSS) testing deployments in place of large banks of cable modems, which would be cost prohibitive.
-
Product
Structural Durability Solutions
-
Instron offers a variety of testing systems and rigs for static, quasi-static and dynamic loading of structures and components. This includes Component Test Systems, Shaking Tables, Road Simulators, Axle Test Systems, Full Vehicle Test Systems, Wheel Test Systems, Shock Absorber Test Systems, Elastomer Test System and Dynamic Torsion Test Systems.
-
Product
PXI Battery Simulator 2.8 Amps
41-753-001
-
The 41-753 is a battery simulator module that can be used to simulate the power supplies of cellular phones and other portable battery devices. It features fully floating output terminals that can deliver voltages up to 6 Volts. The fast responding remote sense connections allow the module to regulate the supply voltage at the device under test.
-
Product
Software Tester & Test Manager
-
With their ability to replicate all types of networks (i.e. Wide Area Networks, the Cloud, over Wireless, Radio and Satellite links etc. ) iTrinegy network emulators provide testers with the ability to test application performance in a realistic simulation of the target network environment.
-
Product
Solar Spectrum Test Chamber / Solar Radiation Test Chamber
-
WEIBER Solar Spectrum Test Chambers are one of solutions to be utilized in large scale PV testing program. We offer customized as well as standard multidimensional test program for PV modules in reasonable prices. This system delivers the weathering stress representative of long term outdoor exposure.Our flexible system can be designed according to our test requirements, to suit environmental test conditions like volume, temperature, humidity solar radiation intensity and other measuring instruments. Weiber provide Solar Radiation Test Chamber.WEIBER solar test system are recognized for superior solar simulation environmental Testing, evaluating outdoor use product reliability, quality & safety. This technology allows for very high concentrations of UV energy without excessive heating of test samples. Custom mounting and cooling can be added depending upon specific material exposure requirements. MHGs (metal halide global lamps) are used as radiation source. Weiber provide Solar Simulation Test Chamber.
-
Product
Mixed Protocol Modules
-
The ANET-MxAy offers mixed protocol support, combining MIL-STD-1553 and ARINC429 data bus test and simulation capabilities in one ANET device.
-
Product
ARINC 429 Test And Simulation PMC Module
PMC-429
-
*4, 8, 16 or 32 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*PXI interrupts, star trigger, and PXI clock*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Sorting according to SDI field*VXI Plug & Play driver including soft front panel*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
Product
Refrigeration Training Chamber
-
The most effective way to help a student learn about refrigeration is through hands-on experience. Skill retention and efficiency improve when they are practiced and applied in a setting that simulates real work experience. In cooperation with a local vocational program, Thermotron developed the S4-T Refrigeration Chamber.
-
Product
Continuous Real-Time Data Feeds
Application and Threat Intelligence (Subscription)
-
Keysight Network Applications and Security
Test and simulation conditions must reflect the latest security threats and applications so that you can ensure your equipment and systems will perform reliably and protect networks from the most advanced and malicious traffic. With Ixia's BreakingPoint Application and Threat Intelligence (ATI) program, we do the research for you by identifying and generating security attacks and application protocols that keep you current.
-
Product
Four-Wheel Drive Single Roller Dynanometer for Cars with Axle Load of up to 2.4T
MSR 500/2 CAR 4WD | VP 230036
-
Maschinenbau Haldenwang GmbH & Co. KG.
The MSR 500/2 CAR 4WD single roller dynamometer is used in workshops for designers and tuners as well as in educational institutions. It is especially suitable for performance measurements, tuning and diagnostic work on particularly powerful vehicles. With test speeds of up to 300 km/h, it is used for dynamic and static power measurement. The MSR 500/2 CAR 4WD guarantees optimum measurement accuracy and reproducibility through the active measurement of the towing power.The rolling behaviour of the tyre is the same as on the road. Operating methods such as load simulation, including optional modules for the measurement of external data, e.g. driving cycles, are possible.
-
Product
Recloser Control Analyzer
GEN-I3V
-
The GEN-I3V is a universal analyzer for Recloser Controls and a Recloser Simulator of up to 15 Amps. In addition to current injection up to 15A, it also supplies 3 voltage sources to perform a complete range of testing and provides high precision curves in no more than 10 minutes.
-
Product
Simulation Design For Manufacturing
-
Altair offers a unique set of simulation tools to evaluate product feasibility, optimize the manufacturing process, and run virtual try-outs for many traditional, subtractive, and additive manufacturing processes. Users can validate designs early in the manufacturing process with the simplicity and affordability of the simulation software, as well as use optimization technology with specific manufacturing constraints to design better, more efficient products.
-
Product
6U Single VME Slot Intelligent Interface Card
IIB-3910-VME-2C
-
The IIB-3910-VME-2C is a 6U single VME slot intelligent interface card providing complete STANAG 3838 andSTANAG 3910 test, simulation and bus analysis capability, for two 3838 dual redundant and two 3910 buses, which support optical dual redundant and electrical single redundant 3910 protocols.
-
Product
EMBEDDED MMC (EMMC)
SD 3.0 / eMMC 4.51 IP Family
-
The eMMC Host IP is an RTL design in Verilog that implements an MMC / eMMC host controller in an ASIC or FPGA. The core includes RTL code, test scripts and a test environment for full simulation verifications. The Arasan MMC / eMMC Host IP Core has been widely used in different MMC applications by major semiconductor vendors with proven silicon.
-
Product
Low Power Programmable AC Source with Transients
61500 Series
-
Chroma Systems Solutions, Inc.
Power:500VA (61501)1500VA (61503)2000VA (61504)4000VA (61505)Voltage range: 0-150V/0-300V/AutoCompact size and weight attributable to advance PWM technologyAC+DC output mode for voltage DC offset simulationProgrammable slew rate setting for changing voltage and frequencyLow output impedance for testing IEC 61000-3-2 (61505)Programmable output impedance for testing IEC 61000-3-3LIST, PULSE, STEP mode function for testing power line disturbance (PLD) simulation capabilityIEC 61000-4-11 voltage dips, short and variation simulationHarmonics, inter-harmonics waveform synthesizer for testing IEC 61000-4-13Programmable voltage, current limitComprehensive measurement capability, including current harmonicsHigh output current crest factor, ideal for inrush current testingTurn on, turn off phase angle controlTTL signal which indicates output transientAnalog programmable interface3 units combined to 3-phase power outputEasy-use software for operation and IEC regulation testOptional GPIB and RS-232C interface
-
Product
Ethernet/AFDX/BroadR-Reach PXI Fault Insertion Switch - 8 Channel
40-201-008
-
This high bandwidth differential PXI fault insertion module is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This module supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
Product
PCI Precision Resistor Card 9-Channel, 1.5Ω To 925Ω
50-297-021
-
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI High Density Resistor Card 5-Channel, 12-Bit, 0 To 4k Ohm
50-295A-021-5/12
-
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Electrical Ground Support Equipment:
EGSE
-
Keysight provides a variety of configurable test systems for satellites and satellite flight hardware; including Solar Array Simulators, Battery Simulation and Conditioning, RF signal simulation and analysis as well as fully custom solutions.
