Screw
See Also: Thread, Linear Actuators
-
product
Digital Frequency Meter
CSF-400
Measuring frequency. Accuracy: +/- 0.05%. 4 Digital display: 9999 Input Max. 400Hz/600 V, 30KHz/12V. Aux. Power AC 115/230V +/-15%, 50/60Hz. Isolation Aux. Power 12Vdc, 24Vdc, 48Vdc, 110Vdc available in option. Easy-to-wire, screw type terminal. Outside dimensions is DIN standard (96mm x 48mm) High stability & low cost.
-
product
Dual MAX31865 PT-100 RTD to Digital Breakout
SEN-30202-PT100
Dual channel breakout board for the MAX31865 RTD-to-Digital converter from Maxim. Two breakout hardware configurations are available standard, designed to interface with either the PT100 or PT1000 platinum RTDs. For non-standard applications, including thermistors, custom hardware configurations can be accommodated. Contact Technical Support for more information. RTD devices may be wired in 2, 3 or 4-wire configurations using the 4-pin screw terminal input. The MAX31865 breakout is interfaced via 3 or 4-wire SPI with a data-ready output for specific operating modes. An LDO and a high-speed level shifter are included to allow interfacing with microcontroller devices between 3.0V and 5V (all Arduinos, Raspberry PI, etc) without sacrificing device performance.
-
product
Optical Balloon Theodolite
F. W. Breithaupt & Sohn GmbH & Co.KG
*Robust instrument*Bright scope with wide field occular and fix focus*Magnification 16x (20x optional)*Field of view 55,6m/1000m (optional 27,8m)*Open finder sights*Double vertical circles (reading from both sides of the instrument)*Reading of circles 0,1°*Convenient targeting through friction-controlled by endless wormdrive screws*Accessories upon request like alarm clock, filters, tripod etc.*Long life cycle, full spare part availability*Made in Germany
-
product
Automated Tuners / Impedance Tuners / Load Pull Tuners
MT97x, MT98x and XT98x series automated tuners (also known as automated impedance tuners and automated load pull tuners) are precision instruments that are optimized for a broad class of in-fixture and on-wafer applications, and may be used in any automated or manual application requiring the ability to match the impedance of a microwave circuit element or to establish specific impedances at a terminal interface. The tuner design is based on the slide screw concept using the inherently broadband slab-line transmission structure. Each unit has two non-contacting probes deliver high VSWR with superb accuracy and reliability over a wide frequency range. These probes can be fully retracted leaving a low-loss, well-matched transmission line, which is a significant benefit in power related applications where two-port tuners capable of handling large amounts of power are required. As integral components of Maury Device Characterization Solutions, these PC-based tuners are controlled using Maury's family of Device Characterization Software tools, including MT930 IVCAD, MT993 ATS and the DLL-based measurement automation environment. Maury Microwave automed impedance tuners are ideal for load pull, harmonic load pull, active load pull, hybrid active load pull, noise figure, noise parameters and all automated tuner applications.
-
product
sbRIO 2mm IDC Connector Breakout
784507-01
50-Pin Male IDC to 66-Pin Female Screw, Breakout for sbRIO Terminal Block - The sbRIO Breakout Box is a 2 mm insulation-displacement contact (IDC) connector breakout that provides easy access to the multifunction I/O and digital I/O connectors on CompactRIO Single-Board Controllers. The connector breakout provides screw-terminal access to the onboard I/O, which eliminates the need to create a custom cable. You can use this accessory at your desk or mount it directly to the controller for an alternative wiring solution during deployment.
-
product
96-Pin Micro-D Connector Block, Female With Backshell
44-965-096-F
This connector block provides a simple method of connecting to high density 96-Pin SCSI Style Micro-D BRIC connectors. The screw terminals accept wires up to 20 AWG and use a rising cage screw clamp mechanism to minimize risk of copper strand breakage. The metal shell includes an internal insulation barrier under the carrier board.
-
product
Electric Linear Actuators
MaxJac
The MaxJac actuator features a smooth high response ball screw and gear motor and utilizes a proprietary guidance bushing to provide precision smooth linear actuation. Standard equipment includes a 12 volt motor with potentiometer feedback. It is ideal for throttle control, solenoid actuation, and valve actuation in such applications as construction equipment, motor vehicles, marine, and blood infusion pumps.
-
product
Lamp gauge
E27
Shenzhen Chuangxin Instruments Co., Ltd.
To check the maximum dimensions of the screw thread and dimension T1 minimum of caps on finished lamps shown on sheet 7004-2.
-
product
SH25M-10F Cable, 25-Pin Male D-SUB to 10-Pin Female COMBICON, Shielded Multifunction Cable
190654-02
25-Pin Male D-SUB to 10-Pin Female COMBICON, Shielded Multifunction Cable - The SH25M-10F Cable, sometimes referred to as SH10F-25M, connects C Series DAQ devices with a 10-pin screw terminal to a 25-pin D-SUB. The SH25M-10F Cable is offered in different lengths.
-
product
BF-Series Mini Screwdriver Models
The E-DRIV® BF-Series miniature soft stop models is designed with an unique "soft-stop" shock absorbing clutch that is ideal for fastening shock delicate components such as disk drives, plastics, and electronics. The ergonomically designed soft stop clutch reduces impact and vibration transmitted in the screw fastening process, which delivers less torque reaction to operator. The electric screwdriver offers an adjustable speed setting. Designed for precision torque control the brushless motor design ensures durability and reduces the standard maintenance costs associated with brush type electric screwdrivers. The mini BF power tool is ESD certified, ensuring less than 1 Ohm at the bit tip. ESD management assures product quality, cost savings and a reduction in overall ESD failures.
-
product
Shaft Speed Sensors
Electro-Sensors offers many shaft speed sensors for virtually any environment. Our Hall-Effect and Magnetoresistive Sensors sense magnetic targets and work with our magnetic pulsers (Discs, Wraps, and Wheels). Our proximity sensors sense ferrous metal targets, including bolt-heads, screws, gearteeth and keyslots. Our speed sensors monitor shaft speed of equipment and output data as PNP, NPN, or 4-20 mA signals. The sensor data can be used by facilities to monitor machinery and safeguard equipment. Monitoring shaft speed is a fundamental aspect of hazard monitoring and should be utilized by any facility with rotating shafts.
-
-
product
200-Pin LFH Connector Block, Male
40-965-200-M
Suitable for use on the front of PXI modules this connector block provides a simple method of connecting to high density 200-Pin LFH connectors. The screw terminals use a rising cage screw clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximise copper cross sectional area and insulation properties.
-
product
Digital Input/Output Expander (Normally-Open Relay Contact Outputs)
ENVIROMUX-DI16DOR16
Adds 16 digital inputs and 16 digital normally-open relay contact outputs to the ENVIROMUX-2D/5D/16D. Interfaces with the ENVIROMUX-2D/5D/16D via the RJ45 Sensor Port. Digital inputs: 16 screw terminal pairs for connecting dry contact devices; One screw terminal pair for tachometer; 0 to 255 Hz. Accepts 26 to 16AWG wire. Potential free. Voltage range: 0 to +36VDC. Over-voltage surge protected. Digital outputs: 16 screw terminal pairs for normally-open relay contact outputs. Accepts 26 to 16AWG wire. Potential free. Rated switching load: 0.5A @ 125 VAC, 1.0A @ ±30VDC. Fused. Supports CAT5/5e/6 cable up to 500 ft. (152.4 m). Includes 5V/3A power supply. Compatible with ENVIROMUX-2D/5D/16D. Dimensions WxDxH: 6.49x3.10x1.78 in (165x79x45 mm). Regulatory approvals: RoHS.
-
product
Ultra HD Surgical Monitor Series
ASM27UHB
The ASM27UHB Series of medically certified UHD surgical monitors features clear image and accurate color reproduction to fully support medical personnel. As a result of its hygienic surface design that eliminates exposed screw heads and air vents, the ASM Series can be easily and quickly cleaned using all common disinfectants and cleaning agents. This ensures a high level of hygiene in pathogen-sensitive environments such as the OR. The ASM Series’ hygienic design also can speed up turnaround time and operating theater preparation.
-
product
Bolt Extensometers for Proof Load Testing
Model 3565
Jinan Testing Equipment IE Corporation
The Model 3565 uses hard conical points to contact the bolt at the center of the head and at the bottom. It is fully adjustable for different length bolts ranging from 25 mm (1 inch) in length to 150 mm (6 inches) standard. Extension beams are available for longer bolts. The standard maximum measuring range is 1.25 mm (0.05 inches). Generally, on longer bolts this extensometer will be self-supported without requiring any centering marks or punch marks on the bolt. For shorter bolts these marks may be required. If the conical pins are sharp, marks are often not needed even on the shortest bolts.The extensometer has a zero adjustment screw to adjust the length between the contact pins. This is used to set the output voltage to zero, which corresponds to the correct starting position for the test. It also includes a breakaway lower arm. In the event a bolt should fail, the breakaway arm snaps free, helping to prevent damage to the extensometer. This is easily re-installed. In the event that bolt failures are likely during a test, it is recommended the user attach a cord around the upper part of the beam and tie the other end to the test frame to prevent the extensometer from falling. The conical point contacts included with the extensometer are made from tungsten carbide.The Model 3565 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
product
Tensile Grips
Instron offers a wide array of tensile grip solutions engineered to suit virtually any materials testing application, with force capacities from one gram to two meganewtons covering fibers, films, metals, composites, elastomers, textiles, and more. From classic manual wedge and screw side action grips to pneumatic and hydraulic powered versions, Instron’s grips support static and dynamic testing across ambient and temperature environments. Built to global standards and backed by decades of durability and service, these tensile grips help labs reliably secure specimens while delivering consistent, repeatable test results—even for highly specialized or custom applications.
-
product
Enclosure, 25 Module, Large
410112368
The 25 Module Enclosure, Part # 410 112 368 is made of aluminum, painted black and secured to the ITA by eight socket head cap screws (included). It is equivalent in length to the 50 module enclosure with a depth of 6" and handles on each side.
-
product
Enclosure, G2, 2 Module, No Cable Exit (for ITA p/n 410120112)
410114365
Enclosure, G2, 2 Module, No Cable Exit (for ITA p/n 410120112)This ITA enclosure is for use with G2 ITA p/n 410120112, which is an ITA that does not include the standard removable housing/backshell. This enclosure is screw mounted to the ITA and does not include a cable exit.
-
product
NI-9222 , ±10 V, 500 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
783283-01
±10 V, 500 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The NI‑9222 performs differential analog input. This module is well suited for applications such as ballistics, impact, and blast wave testing. The NI‑9222 can sample at the maximum sample rate per channel while the module next to it samples at a much slower rate, which is ideal for mixed-measurement test systems. There are two connector options for the NI‑9222: a 10‑position screw terminal or a 25‑pin D‑SUB connector.
-
product
SparkFun MicroMod GNSS Carrier Board (ZED-F9P)
With GNSS you are able to know where you are, where you're going, and how to get there anywhere on Earth within 30 seconds. This means the higher the accuracy the better! GNSS Real Time Kinematics (RTK) has mastered dialing in the accuracy of their GNSS modules to just millimeters, and that's why we had to put it on this board! With the flexibility of the MicroMod's M.2 connector, you can easily test and swap out different MicroMod processor boards for your application. Simply match up the key on your board's beveled edge connector to the key on the M.2 connector and secure the boards with a screw. This means solderless access to the ZED-F9P modules features via UART1, UART2, SPI, and I2C ports!
-
product
Triaxial Accelerometers
Metra Mess- und Frequenztechnik in Radebeul e.K.
Triaxial accelerometers are intended for simultaneous measurement of vibration in 3 perpendicular axis. All models have a central drilling for easy screw attachment and convenient axis alignment.
-
product
37-Pin D-Type Breakout DIN Female
40-967-037-F
This termination option is capable of accepting heavy duty connection wires and uses rising clamp screw terminals to minimize the danger of copper strand damage. Users should care take to protect the termination, provide a suitable method of restraining the cables, and ensure appropriate electrical safety precautions are observed.
-
product
TB-4300B, 96-Pin Female DIN to 25-Pin Female Screw Terminal, 300 V, PXI Module Mount Terminal Block
781338-02
NI TB-4300B Terminal Block for PXIe-4300, 300V Input.
-
product
Posi Drives® (Lead Screw Driven)
Del-Tron's Posi-Drive™ lead screw actuators are compact and economical, taking the work out of designing linear motion systems. Available in 3 size profiles, our lead screw actuators require no alignment of components and install with standard fasteners. They are fitted with anti-backlash lead screws and multi-beam couplings with high speed misalignment capability and standard NEMA motor mounts. Available in one, two or three axis configurations these stages travel up to 12”.
-
product
68-Pin SCSI Micro-D Conn Block DIN
40-966-068-F
Suitable for mounting on DIN Rails this connector block provides a simple method of connecting to 68-Pin SCSI Style Micro D connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. The metal shell includes an internal insulation barrier under the carrier board.
-
product
HD-Series Automation Electric Screwdrivers
The HD-Series automation electric screwdrivers operate with only the HDC controllers. The HD-Series electric screwdrivers feature a high performance brushless motor design that provides durability and reduces the common maintenance costs associated brush type electric screwdrivers. These brushless electric torque screwdrivers are engineered for automation assembly applications that provide manufactures with a rapid, reliable and precise method of fastening screws. The technology of these automation tools provide tighter process control and higher quality standards, while keeping costs down. The patented HD-Series hybrid torque control system is the world's first torque tool using both air and electric power to set and control torque.
-
product
Data Logging Kit
ThermoVault
Oven Temperature Profiling kit. Comes with TC101A Thermocouple based Temperature Data Logger with screw terminal, Thermally insulated enclosure, and Type K thermocouple probe.
-
product
ITA, G6, 6 Module, With Protective Cover
410104273
This G6 ITA is equipped with a removable EMI-shielded backshell. This backshell slides up to provide access to wires and connectors. This ITA also includes a keying feature. Removable and adjustable U-shaped cable clamps are attached by screws to the ITA frame and allow ITA modules to be pre-wired before assembly. The clamps can hold cable bundles with an oblong bushing effective diameter of 1.59". ITA strain relief plates are not needed.
-
product
General Purpose Surface Temperature Assembly
S2-2
The Series S2-2 General Purpose Surface Temperature Assembly is ideal for monitoring the temperature of indoor distribution lines when it is not possible to penetrate the pipe. The plastic housing is in the shape of a standard junction box with multiple knockouts for easy conduit access. The strap-on connection quickly wraps around a pipe and can be securely tightened using a flat head screw driver. The Series S2-2 can be ordered with a choice of 11 output options that allow it to communicate to any standard building control system
