-
Product
Control Units
-
For integration into a larger system or for automated measurements, the gain control unit for automated systems lets you control the settings of the intensifier attachment. The control unit uses standard TTL and analog signals for communication, allowing the user to switch the intensifier on or off, alter the gain and the anode current limit of the image intensifier without the need of software integration.
-
Product
Motor Termination Units
-
Since the rise time of IGBTs are in the range of a few tens of nanoseconds (between 50ns-200ns), even short cables between PWM motor drives and motors cause voltage doubling at the motor terminals due to Travelling Wave Phenomenon as in transmission lines. The insulation of motor windings are prone to failure due to high voltage spikes if necessary precautions are not sufficiently taken. RC Type Output Filter Modules reduce these high voltage spikes to protect motors by connecting to stator terminals.
-
Product
Inertial Measurement Units
IMU
-
Analog Devices inertial measurement unit (IMU) sensors are based on multiaxis combinations of precision gyroscopes, accelerometers, magnetometers, and pressure sensors. Our technology reliably senses and processes multiple degrees of freedom, even in highly complex applications and under dynamic conditions. These plug and play solutions include full factory calibration, embedded compensation and sensor processing, and a simple programmable interface.
-
Product
Programmable Logic Units
-
- Programmable FPGA to implement complex logic functions- VHDL coding expertise not required- User-friendly software tools for board programming- Pre-programmed set of standard functions (N1081B/DT1081B)- Different I/Os connectors and standards available (NIM, TTL, ECL, LVDS)
-
Product
Plate Demagnetizing Unit
DM-P
-
Easy handling plate demagnetising unit for demagnetizing parts of ordinary steel and iron. Also suitable for subsequent implementation in automatic systems.
-
-
Product
Hydraulic Power Units
3520 Series
-
The 3520 Series HPUs are used to provide varying flow rates of hydraulic oil at high pressure, to operate Instron® Dynamic and Fatigue and Multi-Axial Testing Systems. In the lower flow region, the 3520 Series includes the following model variants:
-
Product
Manual Clemen Unit
Elcometer 3000
-
The Elcometer 3000 Manual Clemen Unit is a robust and simple to use instrument for evaluating the resistance to scratching of a coated surface.
-
Product
Generator Monitoring Unit
-
Avoids the requirement of 2 different meters (energy and VAF in one)Reduces the cost and simplify wiringHigh resolution reading with auto scaling in LEDEnergy consumption in counter even if CT is reversed
-
Product
Energy-Conservation Unit For Servopulser Hydraulic Power Supply Unit
ECU1/ECU2 Series
-
Up to 50 % energy savings. Contributes to reduced CO2 emissions and lower running costs. The conventional hydraulic power supply unit for fatigue and endurance tests is always driven at full power to achieve the maximum test force and maximum velocity and the hydraulic power supply unit is selected in order to satisfy the maximum test performance. Therefore, depending on the test conditions, energy is excessively consumed. With the ECU Series the motor rotational speed and the supply pressure of the hydraulic power supply unit can be set in multiple stages, so energy savings of up to about 50% can be achieved depending on the test conditions and test circumstances. It is used in combination with the Servo Controller 4830. (The Servo Controller 4830 is provided separately.) * Appearance and specifications are subject to change without notice.
-
Product
Ethernet/AFDX/BroadR-Reach PCI Fault Insertion Switch - 4 Channel
50-201-004
Fault Insertion Unit
This high bandwidth differential PCI fault insertion card is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This card supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, Broad R-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground.
-
Product
Caraya Unit Tester
-
Caraya is a new experimental open source assertion and unit testing framework for LabVIEW. It takes a whole new approach to unit testing; your VI is your test. Caraya allows you to convert your manual test VIs you use for debugging into unit test cases with nearly no effort. Even running the tests is easy, just run the test case VI. Caraya significantly lowers the barrier for developers to write unit tests leading into improved overall code quality in real-world projects where developers don’t always have the luxury to write unit test cases first.
-
Product
Power Supply Unit
PS-18V-U
-
Panasonic Industrial Devices Sales Company of America
A Portable Power Supply Unit available from Panasonic.
-
Product
Diagnostic and Service Units
-
- Reliable wireless data exchange for mobile machines- Real-time diagnosis via CODESYS programming system- Data display and storage via internet portal- Display and processing of position and route data- Different interfaces for integration into the machine network
-
Product
PXI/PXIe Fault Insertion Switch, 74-Chan 2A, N/C Through Relays, Fault Buses on M & U
40-190C-012
Fault Insertion Unit
The 40-190C-012 (PXI) and 42-190C-012 (PXIe) are fault insertion switches with 74 channels. They are part of a range of modules available with 74, 64 or 32 channels and are primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
Pulsed Source Measure Unit
-
The SpikeSafe SMU is a precision pulsed source measure unit that precisely sources pulsed current and simultaneously digitizes voltage. Optimized for precise and repeatable high-power LED and laser testing, SpikeSafe™ SMU (Source Measure Unit) current sources deliver precise pulsing with low microsecond rise times, low-jitter triggering and integrated digitizer for more accurate and repeatable high-power LED and laser testing.
-
Product
Intelligent A/D I/O Unit
RAD242
-
Model RAD242 is an intelligent, two-differential-channel, 24-bit analog-input interface unit that includes a Delta-Sigma A/D converter. The converter has a digital output filter with adjustable notch frequency from 10 Hz to 2000 Hz. The pod also has 13 bits of digital input/output. A precision 10 VDC voltage that can be used for transducer excitation is available at connector pin 5. As much as 60 mA current can be provided. It is packaged in a NEMA 4 enclosure for remote installation in harsh environments. RAD242 also provides a user-definable interrupt input and counter/timer input. An optional RAD Firmware Development Kit is available if you wish to use those user-programmable input lines or to develop a custom program.
-
-
Product
Source Measure Unit (SMU)
-
Source and Measurement Units (SMUs) are devices that generate voltages or currents and can measure them simultaneously using the integrated measurement units (VMU, CMU).
-
Product
PXIe Precision Source/Measure Unit, 15 MSa/s, 100 FA, 60 V, 3.5 A DC/10.5 A Pulse
M9603A
Source Measure Unit
The Keysight M9603A is a PXIe precision SMU featuring best-in-their-class narrow pulse width as narrow as 10 μs. It enables dynamic/pulsed measurements with up to 15 MSa/s for broad emerging applications such as VCSEL optical devices.
-
Product
Photoacoustic Multi-Gas Measurement Unit
GASERA OEM
-
GASERA OEM MODULE is a stand-alone photoacoustic multi-gas measurement unit that can be easily integrated as part of a monitoring system. The module utilizes the same photoacoustic engine as the GASERA ONE family analyzers.
-
Product
CAMAC Multifunctional Logic Unit
CMDGG8
-
The CMDGG-8 is a multi functional FPGA based delay, logic and timing module which provide often needed functions such as gate, delay & pulse generator, logic fan in / fan out, coincidence register and scaler / pre-scaler.
-
Product
DC BIAS CURRENT UNIT
3265B SERIES
-
To evaluate components at currents up to 125 A the 3265B DC Bias Units are used with either the Wayne Kerr 3255B series of Inductance Analyzers or the 3260B Precision Magnetics Analyzer. When one 3265B/25A or 3265BQ/25A DC Bias Unit is connected to an instrument up to 25 A of DC bias current can be set in steps of 25 mA with one unit. Additional DC Bias Units can be added such that with five units connected in parallel it is possible to set DC bias currents up to a maximum of 125 A DC.
-
Product
Servopulser Control Unit
4830 Controller
-
The 4830 has been developed as a controller for servo control type test devices to have the ultimate in advanced performance and operator ease. A single controller unit allows a variety of tests from testing of static properties through to testing of endurance and dynamic characteristics, and has all functions and performance required of a controller for testing machines for actual objects and structures in addition to materials.
-
Product
PXI/PXIe Source Measure Unit Family
PXS(e)840x
Source Measure Unit
The PXS840x PXI SMU family is a high-speed, 4-quadrant source measure unit. Carry out measurements directly on the DUT with the integrated CMU and VMU.
-
Product
Passenger Service Units
-
Astronics serves commercial applications for Passenger Service Units (PSU), offering vertically-integrated solutions through in-house design, manufacturing, and finishing capabilities. For most PSU programs, Astronics assumes full responsibility for design, development, and qualification of new technologies, including manufacturing and final assembly.
-
-
Product
Battery Loading Unit
BLUe
-
BLUe series Battery Loading Units; portable instruments for controlled & monitored discharge of batteries. It is designed for integrated site discharge test, design & QC test and also for monitoring discharge process of battery bank with connected load. Single autonomous unit having inbuilt display, keypad and wireless communication with PC makes it very easy to use. It comes in different configurations ranging from 12V to 380V discharge voltages and 50A to 300A discharge currents. Various options are available to control & monitor the discharge process. With the help of optional Cell Monitoring Unit - CELLMon, voltage of each individual cell can be monitored & data sent to main BLUe unit and then from main unit to PC via wireless communication. Each BLUe unit is supplied with PC downloading & analysis software for real time monitoring of discharge process.
-
Product
Benchtop Units
-
Provide real-time or near-real-time data on chemical reactions and manufacturing processes.
-
Product
Control Unit
Epec 5050
-
Epec 5050 Control Unit is ideal for applications that require plenty of I/O and enhanced algorithms. Epec 5050 control unit has also a large memory and its I/O is widely programmable. For example, PI pins’ threshold voltage can be selected and many inputs have pull-up/pull-down selection.
