Filter Results By:
Products
Applications
Manufacturers
-
product
High Resolution Microscope For Multi-fiber Connector
D SCOPE MT LWD
Designed for inspection of MPO connectors, patch-cords or bulkheads, the D Scope MT LWD checks the cleanliness of the connector face and precisely measures the defects on the optical fiber end-faces. Using Deep Learning technology associated with a high-resolution optical bench, the scratch and defect detection thresholds are significantly improved compared to traditional software.
-
product
Double Embossed Shrouds
BE-DE
Bemcoil-DE (double embossed) is made from roll and continuous welded 18 gauge 304 stainless steel sheet. Each tube passage is almost equivalent to a 7/8 inch OD tube. It is available in three finishes. A number 2B (semi-reflective) finish on the inside face and a number 4 (polished unidirectional) finish on the outside surface, specified when one side of the shroud is to be painted with black epoxy.
-
product
End Face Inspection Microscopes
D SCOPE EFI – D SCOPE EFI-C – D SCOPE EFI-C LWD
The new D Scope EFI for MTP/MPO and multifibers field connectors is a cost effective microscope for inspecting fiber optic patchcords and cassettes.
-
product
4.0mm Hazardous Live Parts Probe
CX-4.0
Shenzhen Chuangxin Instruments Co., Ltd.
Used to verify protection against access to hazardous parts through top openings. Meets IEC, EN, UL and CSA Standards including IEC 1010, EN61010-1, UL3101-1, and CSA 1010-1. The handle and stop face are made of Delrin®. The rod is made of stainless steel.
-
product
Single-Output Software-Defined GNSS Simulator
BroadSim Solo
Designed to address the permanent challenges that engineers face with laboratory capacity and availability, BroadSim Solo was developed to bring advanced GNSS scenario creation to your desk and propel development cycles.
-
product
SAP Testing
ZenQ SAP Testing Services are on-demand, providing the best testing solution for identifying application errors before they make their way into production. Enterprises normally face challenges in analyzing SAP test requirements, handling compatibility issues while configuring, customizing and integrating different modules. We help our clients ease these testing challenges by having test accelerators to bring down cost overheads.
-
product
Drop Test Machine
Single-wing Drop Test Machine Simulate the drop conditions of packaged products when different faces, edges and corners fall to the ground from different heights, thus to understand the damage of the product and evaluate the drop height and impact resistance that the packaging materials can endure while falling down, so as to improve and optimize package design according to actual conditions of the product and national standard range.
-
product
Durometer
HD3000
Hildebrand Prüf- und Meßtechnik GmbH
Durometer Model HD3000 is our standard model. The gauge features a full-sized non-reflective dial face for readability accuracy of 1/2 point. The durometer conforms to DIN 53505, ISO 868, ISO 7619 and ASTM D 2240. Model HD3000 offers maximum accuracy available in a dial model gauge at minimum cost.
-
product
Fume Hood Monitors And Controls
Research in laboratories helps advance science in many different disciplines. Professionals working in laboratories need protection from potentially hazardous compounds. Within laboratories, fume hoods are a primary source or protection. Fume hood face velocity measurements are often used to gauge the performance of a fume hood’s ability to contain and exhaust harmful vapors.
-
product
Heavy Duty Dynamometers
MD-7500-HD
Today’s Fleet Managers are faced with many challenges – most important of which is maintaining a healthy bottom line. With fuel costs at an all-time high, these challenges have become increasing difficult. Fleets being transitioned from fossil fuels to electric propulsion also face challenges with durability and range to make sure routes can be completed on time each and every day. To help combat these problems and others facing fleet managers today, Mustang Dynamometer offers the MD-7500-HD Series Chassis Dynamometer – which features the most advanced diagnostic capabilities in the industry. The MD-7500-HD is designed to simulate the driving conditions that fleet vehicles encounter on the road every day in a safe and controlled shop floor environment so that critical engine and drivetrain systems can be evaluated to insure vehicles are performing properly and at maximum efficiency. What’s more, the MD-7500-HD offers several levels of testing capabilities in a modular, compact package and with capabilities that can be upgraded in the future as your needs change. Every vehicle in your fleet can now be tested and validated before and after a repair to ensure proper diagnosis and repairs have been performed. In addition to testing repaired vehicles, the MD-7500-HD can be used to test vehicles on a regular basis as a preventative maintenance measure which decreases unexpected breakdowns and allows fleet management to control fuel costs while reducing repair costs. Periodic testing keeps fuel consumption to a minimum and helps technicians identify suspect components before they fail. A proactive approach to Fleet Service can prevent unexpected engine and or drive-train failure which saves organizations thousands of dollars in lost fair revenues. At the heart of the MD-7500-HD is a set of three air-cooled eddy current power absorbers. Each absorber, or brake, can hold up to 600-hp (total power of 1,800-hp) – more than enough to simulate a fully loaded transit bus. As the systems PAU’s (brakes) are air-cooled, no water is required to or from the device – eliminating the high cost of water consumption and/or the cost of an expensive water recovery system – which can sometimes exceed the cost of the dynamometer system itself. Mustang is the only company that offers a Universal Fleet Test Bed without water supply requirements. AC Motors can be added to simulate regeneration and validate range for organizations that have transitioned to carbon free electric propulsion. The 7500 is the best solution for fleet managers looking to improve their bottom line and offer disruption-free public transportation.
-
product
Mask Produce and Test Machine
LISUN produce the bfe tester for face mask, pfe tester, melt-blown cloth electrostatic electret generator according to ASTM F1862-17, ASTM F2299-03 (2017), ASTM F2100-2019, BS EN14683-2019, BS EN 14387-2004+A1 2008, BS EN 136-1998, BS EN 140-1999, BS EN 143-2000 +C1-A1, BS EN 149-2001+A1
-
product
Pressure Equipment
Will your pressure equipment be able to stand up to the operating conditions it will face in the future? Take advantage of our experts’ know-how in calculations and analytical expertise – ranging from design and production to conformity assessment. We support you with our extensive experience and state-of-the-art methods and tools. In addition, as a certified body for testing pressure equipment and simple pressure vessels, we are authorized to administer final acceptance and model type approvals on individual pieces of equipment.
-
product
ITC Style VXI Module Shield Kits
* Box design for C-size ITC style PC Boards with 11 slots on their sides.* Pre-machined flat front panel with ejector handle cutouts.* Side shields include 0.375 inch wide vent slot on top and bottom sides for maximum cooling.* Shroudless design fits all VXI chassis.* Each kit includes side shields, front panel, ejector handles, two ejector face places with VXI and ICS logos, all hardware and assembly instructions.* Complimentary layout support includes PCB design template and CAD layout files.
-
product
MPO Visual Cable Verifier Kit
KI-TK832
Kingfisher's unique and innovate MPO Visual Cable Verifier Kit is a quick, versatile and inexpensive way to visually check MPO cable installations and patch leads for polarity and continuity, and overall end face condition. Just connect the source, and view the far end with the microscope to observe the repeating color pattern at the far end.
-
product
MPO Visual Cable Verifier Kit
KI-TK812
Kingfisher's unique and innovate MPO Visual Cable Verifier Kit is a quick, versatile and inexpensive way to visually check MPO cable installations and patch leads for polarity and continuity, and overall end face condition. Just connect the source, and view the far end with the microscope to observe the repeating color pattern at the far end. Fiber 1 is easily identified with a winking light.
-
product
Portable Connector End Face Geometry Interferometer
Thorlabs’ Vytran® Connect-Chek® Interferometer automatically and precisely measures radius of curvature, apex offset of polish, and fiber undercut or protrusion on any PC or APC, single-fiber connector. The CC6000 interferometer uses a non-contact tilted-phase-analysis technique for fast, reliable measurements of connector end faces. This compact interferometer has a carrying handle and must be attached to a desktop or laptop computer (not included) with a standard USB 2.0 port for operation. The included CC6000 software, which is used to control the interferometer, can be installed on a computer with the minimum requirements in the table below. Designed for use in both the factory and the field, this interferometer provides crucial quality information needed to assure long-term performance of fiber optic connectors. One CC250P Mount for Ø2.50 mm PC Connectors and one RT250P Reference Tool for calibrating the CC250P mount are included with the CC6000 interferometer; mounts and reference tools that enable measurement of other PC or APC, single-fiber connectors are available separately below. When used with an appropriate mount for APC connectors, the CC6000 interferometer is also capable of measuring the APC angle and key error.
-
product
Remote Temperature and Humidity Sensor
CHV-RTHS
The CHV-RTHS is a wall-mounted remote temperature and relative humidity sensor designed for use with select Crestron thermostats. The 1-1/2 inch diameter face of the CHV-RTHS protrudes just 1/8 inch from the wall surface and is easily painted or wallpapered to blend into the wall surface.
-
product
Interferometers
Sumix interferometers are designed for inspection of fiber optic ferrules, patch cords, pigtails and bare fiber in the process of polishing and assembly. They enable you to check polishing quality, test connector end face geometry per IEC, Telcordia or your own custom standards and generate reports to supply with your patch cords.
-
product
MPO Visual Cable Verifier Kit
KI-TK872
Kingfisher's unique and innovate MPO Visual Cable Verifier Kit is a quick, versatile and inexpensive way to visually check MPO cable installations and patch leads for polarity and continuity, and overall end face condition. Just connect the source, and view the far end with the microscope to observe the repeating color pattern at the far end.
-
product
Manual Non-Shift Wedge Grips
Manual non-shift wedge grips are versatile grips for tensile testing a wide variety of materials, including metals, plastics, and composites. The open-front design allows easy insertion of specimens and exchange of grip faces. The self-tightening action means samples are held firmly within the grip faces, minimizing slippage during testing.
-
product
Fume Hood Controller
FHC50-01
Fume hoods are a primary source of protection in laboratories. Face velocity measurements are often used to gauge the performance of a fume hood’s ability to contain and exhaust harmful vapors. By measuring and controlling face velocity, TSI FHC50 Fume Hood Controllers provide a higher level of fume hood safety and energy efficiency.
-
product
IEC60065 Socket Torque Balance Tester Torsion Tester
Shenzhen Chuangxin Instruments Co., Ltd.
*Plug and Socket Torque Tester/Device is for compliance is checked by engaging the device, as during intended use, with the socket-outlet of a test apparatus. *Plug Torque Tester/Equipment is a device provided with pins intended to be introduced into fixed socket-outlets shall not impose undue strain on these socket-outlets.The balancing arm of the test apparatus pivots about a horizontal axis through the centre lines of the contact tubes of the socket-outlet at a distance of 8 mm behind the engagement face of the socket-outlet.*With the machine not in engagement, the balancing arm is in equilibrium, the engagement face of the socket-outlet being in the vertical position.After the device has been engaged, the torque to be applied to the socket-outlet to maintain its engagement face in the vertical plane is determined by the position o a weight on the balancing arm.
-
product
Bottom Entry Style Temperature Gauges
Bottom Entry Style Bi-Metal Stainless Steel Temperature Gauges, 100mm face. Available in a selection of Temperature Ranges, with or without a 1/2" BSP Pocket
-
product
Masks Synthetic Blood Penetration Tester
Sataton Instruments Technology CO., Ltd
Medical face masks synthetic blood penetration resistance tester is to evaluate the penetration – splash resistance property of medical face masks by the impact of a small fixed volume of a high-velocity stream of synthetic blood which is projected horizontally. The pneumatically controlled valve will simulate the splatter of blood or other body fluid to disburse at the specimen mask. The tester is suitable to determine the synthetic blood penetration of materials or certain materials used in medical face masks.
-
product
Thermometers
Whatever jobsite needs you face, Klein Tools has a thermometer that will work for you. With both infrared and pocket models, you’ll be ensured a quick and accurate reading whether you can physically touch an object or not.
-
product
LED Volt Meter
Global Digital Instruments, LLC
SenDEC LED Volt meters were developed to fill the need for a modern, high quality, super rugged DC Volt meter at an economical price.?? These solid state meters display the equipment's DC voltage level using a 10 segment LED bar graph display.?? Each bar represents 1 volt and corresponds to the printed voltage on the meter face.?? Models may be ordered for 12, 24, 36, or 48 volt DC systems.??
-
product
DC Meters/Rail Meters:
Digital DC Resistive Voltmeter has a single range of 0 – 2kV. The unit consists of a meter probe, second probe, and connector cable. This unit is designed to measure DC voltage between the negative return rail and overhead positive cantenary conductor used on transit systems. The five position selector switch located on the face, controls OFF, ON, and Test. The OFF positions are for storage and transit. The ON position is for measurements from 0 to 1999 volts with one-volt resolution. The T position tests basic meter functions and the digital display.
-
product
Test Strategy Consulting
Organizations and companies looking to drive change and increase engineering efficiency frequently need to step back and consider the big picture, without losing track of the details. Our consulting provides a comprehensive review of the challenges you face related to the cost and quality of test. We partner with you to develop a better understanding of test from a business perspective and create a strategic plan for aligning the test function with your corporate objectives. It's all geared to developing a test strategy that will help you launch a product or program in the most efficient way possible.
-
product
Wireless Fiber Inspection Probe
OCI-20BN-W
OCI-20BN-W is a portable optical fiber connector inspector for checking fiber and connector end-face cleanliness, ideal for bench top and fiber optic network installation technicians to eliminate error caused by poor quality or improper cleaning.OCI-20BN-W offers excellent viewing on connector/fiber end-face and is able to feature to record and save image/video of fiber end-face; It can be connected to PC or phone by WIFI.More than 40 assorted high-precision tips designed for inspection solutionsAngled/Lengthened tips for awkward positions.Connect smart phone for testing FiberEye2 is the application on an android or IOS smart phone to capture, display and record the fiber end-face image from the Wi-Fi probe.Connect tablet/laptop for testing EFD is the analysis software on Windows tablet/laptop to have dusts, and scratches on end face inspected, analyzed, compiled and reported
-
product
Battery Testing Machine
Dongguan Kejian Instrument Co., Ltd.
Test method is to use test sample cell on a plane, a diameter of 15.8 mm (5/8 inch) rods on the cross placed in the center of the sample.one 9.1 kg or 10 kg weight from a certain height (610 mm or 1000 mm) fell to the samples.Cylindrical or square battery in accepting the impact test, the vertical axis parallel to the plane, vertical steel column longitudinal axis.The longest axis vertical steel column square battery, the bedding face perpendicular to the direction of impact, each battery only accept an impact test.
