-
product
50/75 Ohm Micro Coax Contacts
Rated to 3 GHz using RG 316 or RG 178 Max of 10.5 GHz using RG 316 Double Shield.Rated to 10,000 cycles.50 and 75 Ohm impedance.Mating force of 1.5 lb.High density I/O Crimp contact designed for RG 316, RG 178, and RG 179 wire.
-
product
PXI/PXIe Power Relay Module, 5xSPST, 30 Amp
40-166-002
The 40/42-166-002 is a PXI/PXIe high density power relay module with 5xSPST switches rated at 30A. The 40/42-166 range is available with SPST, SPDT or SP4T switching configurations. It uses power relays which are suitable for switching loads up to 20A at 240VAC (SPDT & SP4T versions) or 30A at 277VAC (SPST versions).
-
product
PXI High Density Precision Resistor Module, 6-Channel, 3.5Ω to 395kΩ
40-298-042
The 40-298-042 is a high density programmable resistor module with 6 channels which can be set between 3.5Ω and 395kΩ with 0.5Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
PXI 5A Power MUX, 1-Bank, 48-Channel
40-651-001
This range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats: 1-bank 48-channel. 2-bank 24-channel 4-bank. 11-channel 8-bank 5-channel. Connections are made via a front panel 50-way male D-type connector. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
product
PXI 8-Slot BRIC Matrix, 220x4 2-Pole (5 sub-cards)
40-562B-122-220X4
The 40-562B-122-220X4 is a high density BRIC8 matrix module with a size of 220x4 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
product
Bit Error Rate Tester
100G NRZ BERT
The C-BERT 2810-4 is a complete bit error rate tester dedicated for 100G Ethernet applications. The four independent channels enable an actual operating environment with traffic on all lanes. The simultaneous testing of 4 channels is much faster than testing each channel individually saving time and money. The BERT eye scan reveals low-probability events and shows the true performance of the DUT to aid troubleshooting. The high RF port density eliminates long cable length which degrades the signal at 25 Gb/s. The OS independent GUI is easy to install and enable remote control from everywhere. The complete and compact C-BERT is a powerful and cost efficient test solution for 100G Ethernet.C-BERT MI-PE2810-4 Product sheet_rev05.
-
product
PXI 20 Banks of 8 Channel 1 Pole MUX
40-615-022-20/8/1
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
product
MTCA 4.0 1000W PS
The WIENER MTCA.4 is a low noise and ripple / high power density power supply in a double height / double width form factor. Designed according to the PICMIC MTCA-4 standard it provides 1000W for 12V payload power as well as 3.3V management power.
-
product
PXI BRIC8 FIBO Matrix Dual 20x4 3pin brkout
40-592A-101
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units.
-
product
DC Power Supplies
SG Series
AMETEK Programmable Power, Inc.
The Sorensen SG Series (hereafter SG Series) represents the next generation of high power programmable DC power supplies. The SG Series is designed for exceptional load transient response, low noise and the highest power density in the industry. With a full 15 kW available down to 20VDC output in a 3U package the SG Series leads the industry in power density. The power density is enhanced by a stylish front air intake allowing supplies to be stacked without any required clearance between units.
-
product
PXI/PXIe MEMS Optical Switch, Single Insert/Bypass, Multi-Mode, 62.5/125 Fiber
40-860A-512-M-HI
The 40/42-860A-512-M-HI is a PXI/PXIe single insert/bypass switch with ST connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode
40-850A-214-M50
The 40/42-850A-214-M50 is a PXI/PXIe 4-channel multiplexer with SC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
PXI 4 Slot BRIC 25x32 1-Pole (5 sub-cards)
40-562A-021-25X32
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
PXI Octal 3:1 High Voltage Power MUX
40-331-005
The Pickering Interfaces 40-331/332 High Voltage Power Multiplexer and Matrix Modules are suitable for applications requiring high voltage power relay switching with high density. They feature current handling up to 5A, 1000VDC/1000VDC peak cold switching and 110VDC/250VAC hot switching. The 40-331 is available as a single 24:1, dual 12:1, quad 6:1, hex 4:1, octal 3:1 or twelve 2:1 multiplexer, and the 40-332 is available in 12x2 or 6x4 matrix configurations. Connections are made via a front panel mounted 37 pin high voltage D-Type connector.
-
product
PXI 2 Banks of 40 Channel 1 Pole MUX
40-615-021-2/40/1
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
product
PXI 2 Amp MUX, Single 8-Channel 4-Pole
40-635-103
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
product
DCDC
SC20A Series
The SC20A series is an economically priced 20 watt DC/DC converter featuring ultra-wideinput range, efficiencies to 85% and a continuous six-sided shielded case. Telecom models (-48) feature thermal shutdown and undervoltage lockout compatible with ETS 300 132-2 paragraph 4.6. Other key features include: overvoltage protection, output trimadjustability, TTL and CMOS compatible remote on/off, short circuit protection and small size. The SC20A series measures only 1.6” x 2.0” x 0.40” and offers a power density of 15.7 watts/cu. in.
-
product
LXI Optical Switching - 2:1 Multiplexer Plugin Module
65-281-381
The 65-281-381 2:1 multiplexer is part of the 65-280 and 65-281 ranges of optical plug-in modules offering matrix & insert/bypass or multiplexer & SPST topologies respectively with all models based on MEMS fiber optic switches and available in various populations per plugin. In addition, a choice of different connector styles to suit most applications is offered: FC/APC (for optimal performance), FC/PC, SC/PC and ST for general applications and LC for high density applications. They use MEMS (Micro-Electro-Mechanical-Systems) based optical switches to route signals between terminals by redirecting the optical signal. This is achieved using micromechanical mirrors driven by a highly precise mechanism activated via an electrical control signal.
-
product
MIL-STD-1553 Module
QPM-1553
The QPM-1553 provides the highest level of performance, flexibility and interface density for MIL-STD-1553A/B on a PMC (PCI Mezzanine Card) module. The QPM-1553 is integrated with powerful software that reduces development time. All 1553 databus functionality is supported from our advanced API (Application Programming Interface).
-
product
PXI 8-Slot BRIC Matrix, 55x16 1-Pole (5 sub-cards)
40-562B-121-55X16
The 40-562B-121-55X16 is a high density BRIC8 matrix module with a size of 55x16 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
product
PXI/PXIe High Density Precision Resistor Module, 9-Channel
40-297A-035
The 40-297A-035 (PXI) and the 42-297A-035 (PXIe) are 9-channel programmable resistors with a range of 2 Ω to 102 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
PXI 2A Multiplexer, 8-Bank, 8-Channel, 2-Pole
40-614C-004
This 8-bank, 8-channel, 2 pole version is part of the 40-614C High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
224 TTL Channels, Digital I/O With 4 Counters PXI Card
GX5732
The GX5732 is a 6U PXI static digital I/O card with 224 TTL I/O channels. Designed for ATE, data acquisition, or process control systems where a large number of discrete I/O channels are required, the GX5732 offers the highest digital channel density in the industry for a single PXI plug-in board.
-
product
PXI Mixed Configuration Relay Module - 12 Cells Populated
40-138-AA-BB-CC-DD (12 CELL)
The 40-138 2A Relay Module with 12 cells populated is a cell-based mixed configuration switching module suitable for applications requiring medium power switching with high density. It provides a broad selection of mixed relay types for greater flexibility and features 2A current capacity and voltages to 300VDC/250VAC.
-
product
PXI 12-Slot BRIC Matrix, 448x8 1-Pole (7 sub-cards)
40-558-121-448X8
The 40-558-121-448x8 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
product
PXI 8-slot BRIC Matrix, 504x12, 1 pole (12 Sub-cards)
40-558-801-504x12
The 40-558-801-504x12 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
product
PXI 4 Banks of 16 Chan 1 Pole MUX
40-657-001-4/16/1
40-657 High Density Power Multiplexer Modules are available in a choice of configurations, containing up to 8 separate multiplexers, all 1-pole switching. They are suitable for switching signals to 110VDC/250VAC at 2Amps, 90W.
-
product
PXI/PXIe RF Matrix, 8x4, 100 MHz, 75 Ω SMB
40-729A-101
The 40-729A-101 (PXI) and 42-729A-101 (PXIe) are 8x4 75 Ω RF matrices with SMB connectors. The 4x-727A/728A/729A range are high density RF matrix modules suitable for switching up to 300 MHz in 50 Ω or 100 MHz in 75 Ω. They are available in 50 Ω or 75 Ω versions with SMB connectors or in 50 Ω versions with a multiway connector. They provide a simple and scalable bidirectional matrix for RF signals and are intended for the construction of high performance switching systems.
-
product
PXI/PXIe MEMS Optical MUX, Single 2-Channel, Single-Mode
40-855A-212
The 40/42-855A-212 is a PXI/PXIe 2-channel multiplexer with SC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
product
PXI Dual 10x4 Matrix 2A 1 Pole
40-546-001
Model 40-546-001 is a high density dual 1-pole 10x4 power matrix module. It is also available in single 10x4, single 10x8 or single 20x4 relay formats: Typical applications include power routing in Functional ATE systems, specifically automotive electronics, for example testing of Engine Management Units.
