Tension
forces causing extension.
See Also: Force, Compression, Crimp Force, Pull Force, Pull off Force, Push Pull Force, Peeling, Gravity, Electrical, Magnetic, Tensiometers, Tensile, Extensometers
-
Product
Mechanical Force Gauges
-
Imada mechanical force gauges are highly accurate instruments used to test the quality, strength or functionality of component parts or products. Imada mechanical force gauges check both compression and tension (push or pull). Peak force can be captured using the peak indicator needle and the tare ring compensates for the weight of attachments. Imada force gauges are constructed with a heavy-duty metal case and all metal components to enable them to retain their calibration for years with proper care. These mechanical force gauges never need charging or batteries and are intrinsically safe in hazardous environments.
-
Product
PXI Strain Gauge Simulators & Pressure Transducer Simulators
-
We offer simulation modules for Strain Gauge Simulation – used in mechanical systems to measure the tension or compression of structural components. These modules may also be used to simulate Wheatstone Bridge Pressure Sensors/Transducers. Simulation requires extremely fine setting resolution with high accuracy and temperature stability.
-
Product
Thin Film Analyser
TFA
-
The TFA instrument has be designed to monitor dissolution rates with a minimal volume of developer, typically ≤ 1 ml. The design uses surface tension to hold the developer in a small gap between the sample and the detector head. The instrument allows multiple measurements on the same sample. Thickness measurement can be made in the same geometry as dissolution measurements.
-
Product
Tensile Compression Force Tester
ESM303
-
The ESM303 is a highly configurable single-column force tester for tension and compression measurement applications up to 300 lbF [1.5 kN], with a rugged design suitable for laboratory and production environments. Sample setup and fine positioning are a breeze with available FollowMeTM force-based positioning - using your hand as your guide, push and pull on the force gauge or load cell to move the crosshead at a variable rate of speed.
-
Product
Super-Safeway Three Wire Circuit Tester
1301270009
-
Super-Safeway Three Wire Circuit Tester, 3 Indicating Lights & Receptacle Tension Tester in Carrying Case
-
Product
Force Sensors
-
General purpose force sensors are offered in either stud or axial mounted configurations. They are internally pre-loaded and can be used for dynamic compression, tension, and impact force measurements. Tapped mounting holes on both ends of the radial connector style support link, platform, integrated link, and free-standing installations. The axial mounted type offers protection of the electrical connector and sensor cable from potential damage during drop testing and in free-standing installations. Supplied impact caps facilitate impact and drop force measurements.
-
Product
Cable Working Equipment Products
-
DLM’s long involvement operating in and supplying to the Cable Laying Industry has led to the development of a multitude of products to support operations. From a host of Grapnels for PLGR operations, Saddleback Monitors to measure cable Tension right through to rigging and deck equipment.
-
Product
ACoustic QUantification of IncidenTs
ACQUIT
-
In regions with tensions, the cease fires agreed upon along a border line are usually fragile. The global community is often asked to send in observers trying to maintain the peace and to report on violations from both sides. There is a need for well described events in the formal reporting, when, where, what kind of weapon etc.
-
Product
High Temperature Hot Mountable Furnace Extensometers (1200 Cor 1600 C)
Model 3549
-
Jinan Testing Equipment IE Corporation
The Model 3549 is a major advancement in the design of externally mounted, furnace extensometers. This new extensometer is designed to meet the stringent requirements of strain controlled testing as prescribed in ISO 6892, while introducing many new innovative features that help improve productivity with static testing applications (tension and compression testing) and long term testing such as low cycle fatigue and creep. The overall design reduces any influence from common lab environment vibrations. This unit also incorporates a new feature that allows the user to precisely set the contact force against the test specimen. This allows for even and repeatable contact force, limiting contact force induced errors. This extensometer mounts on a slide bracket (included) that can attach to the load frame of your test system; optional load frame mounting brackets are available. The gauge length for the 3549 is automatically set prior to mounting on the test specimen, which allows for hot mounting after thermal equilibrium has been reached.
-
Product
Automatic Oil Interfacial Tension Tester
HITT
-
Hention Electrical Equipment Co., Ltd.
The HITT Automatic Interfacial Tension Tester is designed and made as per GB/T6541 “Test Methods for Interfacial Tension of Petroleum Products between Oils and Water (Ring Methods)”. It is suitable to determine interfacial tension between mineral oils and water under non-equilibrium conditions (Liquid-liquid interface). It can also be used to determine surface tension of various liquids (liquid-gas interface).
-
Product
Level Measurement
-
Displacer level gauge for liquids from KOBOLD Instruments operates on the Archimedes principle. The level gauge's displacer tube rests inside the tank and is connected to the measuring unit via a spring. As liquid level increases, the buoyant forces of the liquid act on the displacer tube to reduce spring tension, allowing the spring to expand. The spring connects to a magnetic actuator, and the motion of the actuator is picked up by a magnetically linked indicator to yield the tank level measurement. The displacer level gauge is calibrated at the factory for the user's specified liquid density. Special designs with higher pressure or temperature ratings, as well as those made of exotic materials, are always available on request.
-
Product
Digital Torque Meter Torsion Tester
HN-1E~20E
-
Shenzhen Chuangxin Instruments Co., Ltd.
Digital Torque Meter is an intelligent metrologic instrument, which is designed for various torque test and calibration. It's mainly used for electic/manual torque drive, torque screwdrivers, bolt driver, tension wrench and other testers and products which refer to tightening force. It is widely applied in these industries, such as electrical manufacturing, machine manufacturing, car light industry, professional research and tests, and so on.
-
Product
Compact Low Profile Load Cell
1000 Series
-
Compact Low Profile load cells are fully stainless steel, hermetically sealed load cells with a multi-beam internal structure, and fully integrated electronics to provide high level analog or digital outputs. This type of load cell is easy to use for measuring tension or compression loads from 200N (50lb) to 5kN (1000 lb), and is capable of rejecting side forces that would otherwise affect accuracy. This type also offers the user the ability to set the gain and offset (span and zero) electronically, to provide maximum flexibility for the user application.
-
Product
Manual Test Shell For Push And Pull Force Gauge
HST-S
-
Shenzhen Chuangxin Instruments Co., Ltd.
HST Manual Test Stand have HST-J and HST-S model, is specially designed to match all kinds of Push Pull Gauge and applied in tension, compression, insertion, withdraw and fracture test.
-
Product
Superior Electromechanical Universal Testing Machine
WDW-S Series
-
Jinan Testing Equipment IE Corporation
WDW series computer control electromechanical universal testing system for tension,compression, flexure testing is designed according to ASTM, ISO, DIN, EN standards etc.. The electromechanical universal testing system for tension,compression, flexure testing is computer-controlled and precision. Our electromechanical universal testing system for tension,compression, flexure testing is widely suitable for metallic and nonmetallic materials for tension, compression, bending, shearing and low cycle test. The electromechanical universal testing machine features high precision, high stability and high reliability. Graph, test result display, data processing and printing can be done easily by its PC system and printer. Completed with modulus for metal, spring, textile, rubber, plastic and other material test, the electromechanical universal testing system for tension,compression, flexure testing is widely used in many fields such as industry factories, research and development, test institutes and training centers etc. WDW-S series superior materials testing systems adopt robust load frames, precise load weighting system, advanced measuring and control system, and intuitive modular application software. Configured with wide range of accessories for applications, the materials testing systems can provide the best testing solutions for your individual application needs. With 20 years’ experience of materials testing industry and based on abundant application knowledge, we are completely capable of configuring the best solutions and more accurate testing systems for the manufacturers involved in load frame, core measuring and control elements, software package, grip/fixture that based on their specified test application and other requirements.
-
Product
Meters For Contact Angle And Surface Tension
SURFTENS AUTOMATIC
-
Optik Elektronik Gerätetechnik GmbH
Automatic measuring instrument for contact angle and free surface energy with motorized pump, automatic drop placement and motorized specimen table (200 x 200) mm.
-
Product
RFID Label Inspection System
Eurotech RFID FS
-
The Eurotech RFID FS RFID accurately rewinds rolls of RFID labels and validates their receptivity by running them through the Voyantic Tagsurance RFID inspection system. The unit allows stopping at a predetermined editing spot for the removal and replacement of the defective piece, as well as indicating defective labels by a mark printed by an inkjet system integrated with the machine. Adjustment of the closed loop tension control system can be made through adjusting the parameters on the software that control the servo motor control system. This gives the customer a virtual infinite range with which to wind their labels without cracking the inlay or antenna. As well accurate web adjustment and guidance is provided with a web guide system complete with an ultrasonic sensor. The Eurotech RFID FS RFID label inspection system is equipped with the Voyantic Tagsurance for testing the performance of RFID tags. This is done by verifying that the tag responds to commands on its whole operational frequency range, which means testing the tag on multiple frequencies, also outside the RFID reader frequency. Accurate power output combined with the Voyantic Snoop Pro antenna, optimized for testing tags inline at high speed, allows defining precise acceptance criteria and achieving stable quality.
-
Product
Economical Hydraulic Manual Universal Testing Machine
WEW-D Series
-
Jinan Testing Equipment IE Corporation
WEW-D series hydraulic manual UTM is suitable for testing tension, compression and other strengths of various metallic or nonmetallic materials with high strength. The hydraulic manual UTM is capable of testing the characters of materials on physical & technology properties. As a manual control & economical UTM, the hydraulic manual UTM is with reasonable and reliable configurations (load cell or pressure transducer, extensometer, photoelectric encoder, servo motor & driver, standard screws), which can satisfy ordinary testing requirements. Digital controller and computer with software can be equipped on this machine to realize the test date/curve collecting and process. The hydraulic UTM of economical type is easy to operate and is versatile in the applications of metallurgy manufacturers such as steel mills & alloy, reinforced bar etc.
-
Product
Static Load Cells (500 N to 600 kN)
2580 Series
-
The Instron 2580 Series static load cells are high-precision force transducers optimized for use with 5900 and 6800 Series universal testing systems, capable of measuring loads across a wide range (up to ±600 kN) with accuracy to 0.5 % of reading and sensitivity down to 1/1000th of full scale. Temperature-compensated and calibrated on equipment traceable to international standards, they have automatic recognition with an electronic serial number and support electronic calibration, while offering overload protection (up to 150 % without damage, 300 % without mechanical failure). The 2580’s design delivers high stiffness and reliable alignment under load—making it a robust choice for tension, compression, cyclic, and reverse stress testing in materials and components.
-
Product
Quartz ICP® Links
-
Link-style sensors measure dynamic compression and tension. They are constructed using a force ring that is under compressive pre-load between threaded mounting hardware. The threaded mounting on both ends of the sensor supports integrated link-style installations. Versions offering full-scale measurements of 10 lb to 50k lb (45 N to 220k N) compression and 30k lb (130k N) tension are available.
-
Product
Digital Strain Gauge Sensor
ZET 7110
-
The ZET 7110 module is intended for measuring the relative deformation using primary transducers based on tension gauges. These may be either assembled tension gauges (force gauges, torque gauges), or detachable tension gauges connected using half-bridge or bridge mode.
-
Product
Mechanical Testing
-
A range of processes including:Tensile and Compression Load TestingA test piece or component is subjected to tension (or compression) until either a proof load is achieved or failure occurs.Testing can be carried out on both metallic and some non-metallic materials.
-
Product
Automotive Tester
-
An automotive tester can be used to inspect one or more aspects of an automobile. For example, a borescope automotive tester is an automotive inspection camera used by auto body mechanics to see inside car, truck and other vehicle engines before removing any engine parts. Other kinds of automotive tester devices are used to adjust belt tension, test the electronic ignition starter, search for air conditioning leaks, measure the force required to press a brake pedal, determine the antifreeze concentration, or check the paint thickness over collision repairs.PCE Instruments (PCE) offers a wide variety of automotive tester products. These diagnostic support tools help professional automobile mechanics identify a number of vehicle repair needs. PCE's automotive tester products can aid in the diagnosis of many different mechanical and electrical system issues, including but not limited to locating the cause of an engine misfire, testing fuel injector resistance, pinpointing an engine coolant leak, or detecting car cylinder head problems. It's no wonder so many auto repair technicians choose to stock theirs shops and garages with PCE automotive tester products.
-
Product
Force Tensiometers
Sigma 702
-
The Sigma 702 is a standalone force tensiometer that provides accurate surface and interfacial tension measurements (Platinum Du Noüy ring, Platinum Wilhelmy Plate), manual determination of Critical Micelle Concentration (CMC) and density measurements. The open design and convenient control keyboard operations make these instruments easy to use without the need for an external computer.
-
Product
Tool Positioner Balancer
-
The Mini 31 balancer is a small, lightweight tool positioner that allows tools to be positioned over a work area for comfortable operation. The tool will remain at whatever level or position that it is left at. The operator can set the desired tension rate by simply placing a screwdriver into the slotted shaft and turning clockwise to increase tension and counterclockwise to decrease tension.
-
Product
Cable Pulling Analysis
CABLE
-
CABLE quickly solves complex three-dimensional cable pulling tension and sidewall pressure calculations, allowing you to make rapid and accurate design decisions.Don't leave installation to chance.
-
Product
High Strength Electro-hydraulic Servo Universal Testing Machine
WAW-H Series
-
Jinan Testing Equipment IE Corporation
WAW-H series Servo-Hydraulic Testing Machine Computerized is suitable for testing tension, compression, bending and shearing strength of various metallic & non-metallic materials. Equipped with the electronics, computer &software packages, it is capable of controlling the test procedures by the predetermined programs. The Servo-Hydraulic Testing Machine Computerized can also display, record, process and print the test results. The test curves can be drawn automatically in real time. The Servo-Hydraulic Testing Machine Computerized is easy to operate and is versatile in the applications of metallurgy manufacturers such as steel mills & alloy, reinforced bar, aircraft industry, research institutes, laboratories, calibration institutes etc.WAW-H series Servo-Hydraulic Testing Machine Computerized is suitable for testing tension, compression, bending and shearing strength of various metallic & non-metallic materials. Equipped with the electronics, computer &software packages, it is capable of controlling the test procedures by the predetermined programs. The Servo-Hydraulic Testing Machine Computerized can also display, record, process and print the test results. The test curves can be drawn automatically in real time. The Servo-Hydraulic Testing Machine Computerized is easy to operate and is versatile in the applications of metallurgy manufacturers such as steel mills & alloy, reinforced bar, aircraft industry, research institutes, laboratories, calibration institutes etc.
-
Product
Load Cells
-
Force Logic UK provides high-quality load cells, load indicators, and force measurement systems for a variety of industries. All our load cells are manufactured in the UK, and have passed through rigorous quality control standards for precise and accurate measurement, load monitoring systems, and industrial weighing applications. They are suitable for the measurement of static loads and dynamic forces in tension or compression, our load cells cover a wide range of mechanical forces, from 1kg to 1000 tonnes.
-
Product
Force Tensiometers
Sigma 703D
-
Sigma 703D is a simple and robust digital force tensiometer for accurate measurement of surface and interfacial tension (Platinum Du Noüy ring, Platinum Wilhelmy Plate), and density. Manual measurement of Critical Micelle Concentration (CMC) can also be conducted.
-
Product
Dynamic Mechanical Analysis
-
The DMA systems from Anton Paar perform dynamic mechanical analysis in torsion, tension, bending and compression at unprecedented precision. Whatever your DMA requirements are, the DMA systems from Anton Paar are efficiently and comfortably adapted to meet your needs. Use the systems for the dynamic mechanical analysis of solutions, melts, solid bars, films, foils, or reactive resins.
