-
Product
UHF/RFID Power Divider Combiner 2-Way, TNC Female, 350-1000 MHz, 30 Watts
PD2921
-
INSTOCK Wireless Components, Inc
PD2921 is a RoHS compliant, 2 way, wideband, 50 ohm, RF power divider, power combiner furnished with TNC jack female coaxial connectors. All wireless band frequencies in the range from 350 to 1000 MHz are covered with optimal RF performance. Max microwave input power levels up to 40 watts can be handled in both power splitter and power combiner applications. See 2 way power divider input rating tables for additional details.
-
Product
Analogue (1kV below) Insulation Tester
1832 IN
-
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Two continuity test on low ohms : 3Ω & 500Ω.● Compact and lightweight.● 200mA continuity short circuit current.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test.● Live warning and display or external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● BS 16 edition.
-
Product
DAS Trays/ Point-of-Interface (POI)
-
*CCI DAS Trays provide a common connection point to the DAS system for multiple BTS's*Modular design allows support for bands from 700MHz to 2700 MHz*Independent level control for each BTS for adjusting TX & RX power*Easy optimization features including separate Uplink and Downlink control*Can support both 0 dBm and +30 dBmDAS TX inputs (high and low power)*Supports NIMO and SIMO configurations
-
Product
Integrated 5G mmWave Test System
IQgig-5G
-
The IQgig-5G is a fully-integrated, non-signaling solution for testing 5G mmWave products at both the 28 GHz and 39 GHz frequency bands. All signal generation, analysis, and RF front-end routing hardware are self-contained inside a single chassis. The IQgig-5G is license-upgradeable to support the pre-5G and 3GPP standards evolution with up to 1 GHz of tester bandwidth. The IQgig-5G solution has three bi-directional source and measurement ports each with 2.92mm connector coaxial interface.
-
Product
Low Noise Super Wide Band Amplifiers
WBA Series
-
WBA series low noise amplifiers have the octave bandwidth from MHz to GHz. With super low noise figure and exceptional low VSWR, WBA series LNA achieves exceptional gain flatness accross octave or multi-octave bandwidth.
-
Product
Signal Amplifier
9200A
Amplifier
Model 9200A was designed as a general purpose, wide band and high voltage amplifier however, with specific applications in mind. It is built in a small case size to save space and cost but without compromising bandwidth and signal integrity.
-
Product
Small Device Noise Emission Test System
-
The Small Device Noise Emission Test System from VIacoustics is a turnkey solution for the measurement of noise emissions of small devices typically used in computers, consumer electronics, appliances and automobiles. The system includes all hardware and software necessary (see the components tab) for the determinations of sound power levels (1/3 octave band and A-weighted), emission sound pressure levels (normalized 1/3 OB, A-weighted and high resolution FFT) and *ISO 532B loudness. The system is designed to be operated by a technician for production level testing or to be used by an engineer in the product development process.
-
Product
Spectrum Analyzer
BB60C
-
The BB60C streams 140 MB/sec of digitized RF to your PC utilizing USB 3.0, providing an instantaneous bandwidth of 27 MHz, and sweep speeds of 24 GHz/sec. The BB60C has significantly improved performance compared to the BB60A. The BB60C has improved spurious-free dynamic range (SFDR) by 20 dB, flattened the noise floor and band transitions by more than 8 dB, and extended operating temperatures from -40ºC to +65ºC (Option 1). The BB60C also adds new functionality in the form of configurable I/Q streaming bandwidths which will be retroactively available on the BB60A.
-
Product
Single Channel USB Programmable Band-Pass Filter
USBPBP-S1
-
The USBPBP-S1 stand alone USB controllable module provides a single channel of high and low-pass filtering and high-quality instrumentation amplifier for front-end signal conditioning compatible with all popular A/D converter devices. The USBPBP-S1 is powered with 9 to 12VDC so it can be connected to a battery voltage source or the supplied 115-220VAC adapter may be used for operation with wall power anywhere in the world. When programmed from the USB port, the USBPBP-S1 will remember all of the programmed properties between power cycles. Program once and operate as a stand- alone signal conditioner without having to reprogram for every use. This is perfect for turn-key applications. It's easy to connect the USBPBP-S1 into the data collection system. Input and output signals can be routed through BNC connection or using the detachable screw terminal connectors. Optional SMA type adapters are also available.
-
Product
SOA & Raman Amplifier
-
They are designed for distributed Raman amplification in a narrow spectral range in C band.
-
Product
Analogue (1kV below) Insulation Tester
1126 IN
-
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Measures insulation(MΩ) and AC voltage.● LED indiction for testing insulation.● Highly efficiency and accurate DC-DC converter.● Battery check function.● Compact and lightweight.● AC voltage measurement can be made without depressing the test button.
-
Product
Test Antennas
-
Lumistar provides small, lightweight portable fixed antennas for Test applications. They are available in lower L thru S bands for transmit and receive applications.
-
Product
10G DPSK Demodulator
-
Optoplex’s Optical DPSK Demodulator, also known as Delay Line Interferometer (DLI), converts phase modulation to amplitude modulation over the entire C+L band in support of data transmission rates of 2.5,10 or 40 Gb/s. The DPSK demodulator is designed for phase modulated optical communication systemsutilized in commercial, defense and space exploration markets. The device plays a key role in improvingsignal quality and performance to meet the expanding demand for higher data rates and more complextransmission formats within current and next generation systems without major capital expenditure.Optoplex’s DPSK Demodulator is based on a patented free-space optical design, which is compact, athermal and polarization-independent. The measured frequency drift over temperature is only ~0.02 GHz/°C for our standard passive device. Further, this DPSK Demodulator exhibits a total polarization-dependent phase shift of less than 2 degrees over the entire operating temperature range with a high extinction ratio. Optoplex’s DPSK Demodulators can be configured to be fully tunable, colorless tunable or purely passive. Dual-Rate DPSK Demodulator is also available.
-
Product
MCB Thermal Trip Calibration Test Bench (IEC 60898 Cl 9.10.1.2, Annex I.1, IS)
-
The test system is designed and customized to carry out 2.55*Intest as per Table 7 (test c) of IEC 60898 (also mentioned for routine testing of MCBs. The test is done at dc current to exactly analyze and correct the bimetallic properties of the MCB as far as thermal tripping is concerned. The unit comes with a pneumatically operated test fixture with in-built dc stepper motor that is controlled by a micro controller / PC to calibrate the breaker into a narrow tripping band programmed by the user.
-
Product
L Band Splitter, DC Block All Ports
PD5042
-
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.4 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)50 VDC maximum on DC block portsTri Alloy Type N Female (Jack) Low PIM
-
Product
Antenna, Omni-Directional Wideband Discone
EM-6105 | 10 KHz – 2 GHz
-
The EM-6105 is a broad band collinear array allowing very wide Omni-Directional frequency coverage in a single package. Below approximately 100 MHz, the EM-6105 acts as an active vertical rod which offers 10 to 12 dB more signal handling capability than competitive antennas (overload field strength: 2 V/meter) which greatly reduces intermodulation generated signals in a typical read world RF environment. In the congested spectrum above 100 MHz the antenna is passive and contributes no intermodulation products so the overload point is determined solely by the receiving instrument. This immunity to overload can often make the difference between useful signal output and an indecipherable jumble of spurious products and is accomplished without compromising sensitivity. The antenna collapses for convenient storage and transport. The EM-6105 is supplied with an EM-6106 Battery Pack.
-
Product
Small Cell/ Outdoor DAS Antennas
-
*Omni, Quasi-omni, Trisector, Cardioid and Bi-sector formats*Pole mounted and Stadium style antenna configuration*High band, low band and dual band models available*Integrates GPS antenna available on select models
-
Product
C-Band Single Channel FGA Fixed Gain EDFA
HSA4400 (With SNMP)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HSA4400 series is a fixed gain EDFA which is designed specifically for single wavelength optic transmission system. The EDFA adopts excellent optical performance and advanced electric transient control technology, which can efficiently restrain the input optical power change that caused by amplifier, create large transient change of output optical power, so that to protect optical detector and other optical devices in high-speed network.
-
Product
Shortwave Plus 50 MHz Power Amplifier
OM2000A+
-
Thank you for purchasing this new model of the OM Power’s RF power amplifiers line for HF and 50 MHz amateur radio bands. You now own, the OM2000A+, an automatic unit with no knobs, no rotaryswitches on the front panel, just two small switches and one large touch display.Smart design, modern conception, high reliability is the result of OM Power’s development and many years of experience with overall solutions and special attention with the design of the protection circuits.This product is covered by two years of warranty on the amplifier itself and one year for the tube.We wish you will have many years of trouble-free use of this equipment, lots of fun and successful contacts in the world of amateur radio.
-
Product
DC Voltage Sensors
-
DC voltage sensors monitor input voltages ranging from 3 to 500 volts DC with a trip point accuracy of up to 1% in airborne, military and ground power applications. Using internal electronic circuits to detect, monitor and/or sense DC voltage, DARE DC voltage sensors, monitors, and voltage sensing relays can open or close a circuit when a certain pre-set over or under voltage condition exists or the DC voltage falls outside the specified voltage band window.
-
Product
23 GHz Low Noise Amplifier
HMMC-5023
Amplifier
The HMMC-5023 is a GaAs MMIC low noise amplifier designed for moderate gain and low noise from 21 GHz to over 30 GHz. Typical applications of the HMMC-5023 include digital radio communications systems that operate within the 21.2 GHz to 23.6 GHz and 24.5 GHz to 26.5 GHz frequency bands. Moderate gain and low noise temperature make it ideally suited as a front-end gain stage.
-
Product
C-Band Separate Raman Fiber Amplifier
RFA5000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
-
Product
IP67 DC Blocking L-Band Splitter
PD5021
-
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.2 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)50 VDC maximum on DC block portOutdoor Weatherproof ConstructionTri Alloy N Type Female (Jack) 50 Ohm
-
Product
Waveguide Bandpass Filters
-
More details on PE-W28F001 WR-28 band pass wave guide filter can be found on the the waveguide bandpass filter design datasheet specifications up above. WR-28 waveguide bandpass filter from Pasternack is in stock now at our Irvine, CA facility. Our waveguide bandpass filter with WR-28 flanges is part of over 40,000 components for RF, microwave and millimeter wave applications in-stock which are available to ship same day worldwide.
-
Product
Detectors
ZBD
-
VDI offers zero biased detectors (ZBD) for a variety of mmWave and THz applications. These detectors offer full band performance without bias.
-
Product
All-standard All-band Modulator For USB-3
DTU-315
-
Modulation has never been so easy and so beautiful. The DTU-315 is a portable modulator for satellite, terrestrial and cable, all in a single device.A good fit for laptop or tablet, but convenient with desktops and server PCs too.
-
Product
Evaporative Light Scattering Detector
ELSD-LTII
-
The ELSD-LTII utilizes a high-efficiency LED and enhanced digital signal treatment to minimize noise and deliver optimum sensitivity for trace analysis. An innovative cell design also reduces band broadening and allows sensitivity levels below 200 picograms. The high-performance optical detection system can also be used for combinatorial chemistry and high-throughput screening applications. The new Low Temperature Evaporative Light Scattering Detector (ELSD-LTII) is an easy-to-operate, universal detector that identifies analytes with uniform sensitivity regardless of their spectroscopic properties. It is not a spectroscopic detector. Instead, it removes the mobile phase through evaporation and then makes a light scattering measurement of the dried analyte particles.
-
Product
ALL-OUTDOOR RADIO SYSTEM
FreeMile 17/24
-
SAF FreeMile FODU - a new generation license-free 17/24GHz ISM band radio for Ethernet packet data and E1 voice transmission. The new radio system combines excellent features traditionally associated with ISM radios – interference-free operation, high availability, Carrier grade full duplex capacity with no cost of licensing and quick installation. SAF FreeMile radio also offers a user-friendly Web browser based management interface and straightforward installation process to ensure trouble-free experience for any user.
-
Product
Electrodynamic 2-Axis Switching, Simultaneous Vibration Tester
-
It is an electrodynamic 2-axis switching, 2-axis simultaneous vibration tester with a test frequency band up to 2000 Hz.
-
Product
E- And W-Band Test Assembly
StormFlex® 047EW
-
An SF047EW assembly offers test engineers, application designers, manufacturers of mmWave applications the proven durability and robustness of Storm Flex® 047 cable, optimized for coaxial connectivity at frequencies up to 110 GHz.SF047EW cable can withstand handling and flexing and while maintaining the original Insertion Loss and VSWR performance at frequencies previously addressed by waveguides.
