PD Test
partial discharge testing.
See Also: Partial Discharge, Partial Discharge Detection, Partial Discharge Monitors, PD, Partial Discharge Test
-
Product
PD free AC Hipot Test Set
FPA Series
-
FPA Series test sets perform field or factory testing on larger electrical apparatus, including motors & generators, switchgear, bushings, bus duct, etc. This series offers the higher kVA ratings needed (0-6/12 kV AC @ 6 kVA), but is still packaged for portability.
-
Product
Regenerative Battery Pack Test System
17020
-
Chroma's 17020 is a high precision system specifically designed for secondary battery modules and pack tests. Accurate sources and measurements ensure the test quality that is suitable to perform repetitive and reliable tests that are crucial for battery modules / packs, for both incoming or outgoing inspections as well as capacity, performance, production and qualification testing. Chroma's 17020 system architecture offers regenerative discharge designed to recycle the electric energy sourced by the battery module ei ther back to the channel s in the sys tem performing a charging function or to the utility mains in the most energy efficient manner. This feature saves electricity, reduces the facilities thermal foot print and provides a green solution by reducing the environmental impact on our planet. Chroma's 17020 system is equipped with multiple independent channels to support dedicated charge / discharge tests, on multiple battery modules / packs, each with discrete test characteristics. The channels can easily be paralleled to support higher current requirements. This feature provides the ultimate flexibility between high channel count and high current testing.
-
Product
PCIe 2.0 Test Platform
PXP-100B
-
The Teledyne LeCroy PXP-100B Test Platform provides a convenient means for testing PCIe 2.0 add-in cards with a self-contained portable and powered passive backplane. The PXP-100B provides power required for both cards under test, and an interposer can be used for connection to a protocol analyzer. As an alternative to an interposer, the PXP-100B includes two mid-bus probe footprints to allow connection to an analyzer via a mid-bus probe.
-
Product
In-line High-Density ICT System Series 7i
E9988GL
-
The E9988GL Keysight i3070 Series 7i Inline High-Density In-Circuit Test (ICT) system brings industry-leading ICT technologies into your automated manufacturing line, saving resources and optimizing your automated test strategy.
-
Product
Digital Test Instrumentation
EDigital-Series™
-
Teradyne’s eDigital IVI driver controls all parallel digital functional test parameters, including per-pin timing, data formats, pattern data, and timing alignment on 64 channels (32 static + 32 dynamic or 32 differential)—each with an 8M pattern depth and results memory.
-
Product
VR/AR/MR Calibration Platform
-
AR, VR and MR device calibration is critical for product performance. Leverage Averna’s standardized alignment platform to efficiently calibrate cameras and Inertial Measurement Unit (IMU) modules with supreme accuracy. Easily customize or upgrade the base platform into the automated quality solution to best fit your manufacturing requirements.
-
Product
PCI Express 3.0 Test Platform with SMBus Support
-
The Summit Z3-16 Test Platform with SMBus Support allows the Summit Z3-16 to act as a host emulator, and provides a general purpose test backplane and interposer for testing Gen3, Gen2 or Gen1 hosts and devices. In addition, it supports the Summit Z3-16 with SMBus Support by providing SMBus tapping connectivity.
-
Product
200 Vdc External Voltage Bias Fixture
16065A
-
Measure a DUT with up to +/-200 V DC bias and also measure axial/radial lead components
-
Product
EMI Test System
TS9975
-
The R&S®TS9975 is the base system for conducted and radiated EMI measurements. Due to its modular design, it covers a wide range of applications and can be very easily adapted to the measurement task at hand. Any configuration is possible – from conducted measurements and the small precompliance system with a compact test cell to the accredited test system for large equipment under test. Combinations of different applications or incremental expansion are easily possible.
-
Product
Imperial Test Executive
ITE
-
The Imperial Test Executive (iTE) is a UI shell that sits on top of National Instruments TestStand. It provides a simple but elegant interface to execute your NI TestStand sequences. The iTE software was designed to allow general operators to execute ATE testing software without requiring any knowledge of NI TestStand. Training an operator to use this system typically takes less then 5-minutes.
-
Product
PDS Jet Dredge Software
-
Teledyne PDS for jet dredges is designed to the requirements of the dredge operator to carry out their job more efficiently. The operator has a real time overview of the dredger with the top and side views displaying the vessel outline and tube along with the surveyed depths, design, and dredged depth.
-
Product
Functional Test Fixtures
-
Forwessun’s Functional Test Fixtures are tailored to validate the performance of your electronic assemblies, ensuring each product meets critical quality and functional standards. With customisable designs and precision engineering, these fixtures support a range of testing needs—from checking connectivity and function to confirming performance under real-world conditions. Built to handle rigorous demands, Forwessun's solutions are ideal for industries requiring reliable and repeatable results. Whether for high-volume production or specialised testing, our fixtures provide robust, adaptable support to maintain efficiency and accuracy throughout the testing process. We also create, and work with Ingun to create fixtures using the Ingun kit.
-
Product
PD Calibrator
-
PDCAL has excellent pulse-with stability; scale calibration factors are permanently stored inside its flash memory. Thanks to on board photo coupler PDCAL output pulse can be synchronized with the actual line frequency through external surrounding electrical light source systems.
-
Product
Component Test Fixture For N1413 With B2980 Series
N1428A
-
The N1428A is designed to operate specifically with the B2985B / 87B electrometer / high resistance meter. It is provided with two component modules, which are used to hold SMD, lead, and various types of devices. Electrical noise effects are reduced by the employment of a shielded case. A built-in interlock circuit enables safe high-voltage measurements. The N1413A high resistance meter fixture adapter is also required to connect the N1428A to the B2985B / 87B.
-
Product
PDS Rock Dumping and Placement Software
-
Teledyne PDS Rockdump provides the functionality tailored to rock dumping operations to carry out the job more efficiently. The operator has an instant overview of the rock dump vessel with the top views displaying the vessel outline and the slides. Information about the vessel, the design model, surveyed area and/or pipeline is shown in various views that are updated as soon as new data is available and during the rock dump.
-
Product
Faraday Chamber for RF w/Exchangeable Cassettes 340x350mm RCV 9025 for 6TL36
AN133
-
The Faraday Chamber is an add-on for the 6TL36 test handler. This kit is installed into the 6TL36 in the same way a normal test fixture would be installed, being the only difference the fact that different products to be tested will, from that moment on, only need an additional exchangeable cassettes to be tested.
-
Product
Live PD Emulation for the PSL-3424A/L
-
Flexibly Mimic Class 0 to Class 8 Powered Device Per PSL-3424 Test Port. Configure up to 96 IEEE 802.3 PD’s on Any Combination of 2-Pair and 4-Pair PSE Ports with Loading up to 100W on Every Port. Emulated PD’s Automatically Handle PSE Power Demotions (Assigned Class). User-Defined Powered Device Load with Optional Cable Loss Modeling. Emulate 802.3at and 802.3bt PoE-LLDP* Negotiations and Power Adjustments (PSL-3424L). Monitor Multi-Port Live Emulation Status.
-
Product
CDMA2k Analysis Using NI PXI RF Test Instruments
NI-RFmx CDMA2k
-
NI-RFmx CDMA2k is completely interoperable with all NI-RFmx APIs. It provides simple access to the most advanced optimization techniques such as multi-measurement parallelism and multi-DUT measurements. The result is extremely fast and high-quality measurements with minimal software development effort.
-
Product
ESS Performance Test System
-
The Energy Storage System (ESS) Performance Test System is used to evaluate, test, and certify the performance of energy storage systems up to 2MW. The system is a configurable platform with over 200 channels of simultaneously measured AC and DC voltages and currents, environmental temperatures, airflow, and communications. Intuitive software provides real-time monitoring and analysis of power, energy and efficiency to adhere with industry standards. The test system interfaces hardware such as load banks, and controls the ESS to simulate utility applications such as peak shaving and frequency regulation.
-
-
Product
OTP-Based Test System
-
Power electronics assemblies often cannot be tested using conventional technology for their electrical performance. Due to the adaptability of the instrumentation, the OTP concept offers an ideal platform even beyond the space requirements of several control cabinets. In order to achieve high test flexibility with different assemblies, the system was equipped with three-phase AC sources and AC loads as well as a precise three-phase power meter. DC sources and loads with different current and voltage ranges cover the test of frequent DUT operating parameters. Time-dependent voltage or current signals can be stimulated by an arbitrary generator with power amplifier. General measurements such as current, voltage, frequency, resistance can be carried out flexibly at various test points using the matrix concept. An oscilloscope with RF multiplexer is available for high-frequency measurements such as residual ripple, switching processes, etc.
-
Product
Test System Optimized for High Throughput, Low Cost of Test for Single Site, Multi-site and Index Parallel Applications
ETS-88RF
-
Targeting the needs of power amplifier (PA) and front-end-module (FEM) semiconductor manufacturers, the ETS-88RF test system is aligned with the test challenges associated with these direct RF radio wave interface components. The precision with which the ETS-88RF can measure high-gain, wideband frequency performance, adjacent channel leakage and power supply efficiency makes this test system the most cost-effective alternative to bench set-ups. Teradyne routinely provides timely updates to a substantial library of RF Standards (such as 802.11xx and 3GPP) targeted for PA and FEM test.
-
Product
PDS Bar Sweep Survey Software
-
Teledyne PDS Bar Sweep supports different ways to monitor your leveling operation. Teledyne RESON provides the software as well as the sensors to accompany the system.Teledyne PDS visualizes the bar in top, profile, and 3D views indicating where the leveling has taken place. The position and depth of the bar is logged to a digital terrain model (DTM) which is color-coded for depth. It is possible to display a design depth in the profile views, indicating whether the bar has to be lowered or hoisted.
-
Product
Test Port Cable, 1 Mm
11500K
-
Connect test ports to devices, fixtures, or probe tips with this 20-cm cable featuring a return loss of 16 dB minimum
-
Product
Live PD Emulation
-
Flexibly Mimic Class 0 to 4 Powered Device Per PSA/PSL-3000 Test Port. Configure up to 192 Simultaneous IEEE 802.3 PD’s. User-Defined Class 0 - 4 Powered Device Modeling with or without Cable Loss. Emulate 802.3at PoE-LLDP Negotiations and Power Adjustments. Monitor Multi-Port Live Emulation Status. Available to PSA-3000 and PSL-3000 Platforms as optional license feature.
-
Product
Universal PD & EMI analyzer
Spark P3
-
Doble Spark P3 is a universal partial discharge (PD) and electromagnetic interference (EMI) analyzer that uses a software defined radio signal detector to identify characteristics of insulation system deterioration that could lead to the failure of high voltage equipment. It detects signals from suitable sensors in a frequency range between 9 kHz to 2 GHz for PD and EMI, and DC to 500k Hz for acoustic and reference voltage measurements.
-
Product
Universal Test System
LEON System
-
A universal ICT, FCT, ISP and Boundary Scan platform.Based on the ABex platform, which directly integrates Konrad analog bus technology and PXI/PXIe in one chassis, the LEON platform can be configured to solve various test challenges. Due to this architecture only one system provides the complete test flow combining ICT, ISP, Boundary Scan and FCT.Various form factors and configurations allow a perfect combination between cost, speed and test coverage. The modular architecture provides the possibility to reconfigure or upgrade the systems based on your test needs.The LEON System software provides a powerful development and test execution environment which directly supports NI TestStand. All systems and components could be integrated into third party software using supplied APIs.
-
Product
PDS Cutter Dredger Monitoring Software
-
TELEDYNE PDS for Cutter Dredges is designed to the requirements of the dredge operator to carry out their job more efficiently. The operator has a real time overview of the dredger with the top and side views displaying the vessel outline, ladder, and cutter head along with the surveyed depths, design, and dredged depth.
-
Product
VITA 62, 3U Test Fixture
TF-3U-7B041-1
-
This Power Supply test fixture is being proposed as a tool for checking Injector / Ejector operation, proper alignment of the VITA 62 connector and proper alignment of both keys on a Single slot, 3U, VITA 62/SOSA power supply.
-
Product
PDS Wire Crane Monitoring System
-
It shows a real time overview of the wire crane in navigation, profile, and 3D views; displaying the clamshell, pontoon/vessel, design depths and color-coded digital terrain model (DTM). The navigation view highlights the high and low spots and is updated in real time, registering the progress of the dredging work. The registration follows the shape of the clamshell, bucket or orange peel bucket and is visible immediately in all views. The system also shows the open/close status of the dredge tool. Up/down indicators show the operator the exact distance to the seafloor and design depth continuously. 3D design models allow the use of complex designs.
