-
Product
Solar Array Simulator
Simulator
Among other things, solar array simulators are required for testing satellite power supplies. An SAS (Solar Array Simulator), consisting of an interconnection of several Solar Array Simulator modules, maps the solar panels and displays the individual strings connected in parallel. Optionally, the individual SAS modules are monitored by a Second Level Protection, so that the test object is not damaged in case of errors with the voltage sources. Additional circuitry is implemented via project-specific test modules. The signal path to the DUT can be separated, e.g. for dynamic current measurements.The Keysight Solar Array Simulators used were specially developed for satellite applications and cover the significantly higher requirements regarding the control speed of MPP tracking compared to terrestrial applications.
-
Product
Energy Dispersive X-ray Fluorescence Spectrometer
Pharmaceutical Elemental Impurities Analysis System
-
Control of Elemental Impurities in Pharmaceuticals In the pharmaceutical industry, the analysis of elemental impurities is necessary to ensure the safety of pharmaceuticals. In December 2014, the "Guideline for Elemental Impurities" (Q3D) was issued by the International Council for Harmonisation of Technical Requirements for Pharmaceuticals for Human Use (ICH), consisting of representatives from Europe, the U.S. and Japan. In Japan, the "Guideline for Elemental Impurities in Drug Products" (PFSB/ELD Notification 0930 #4 from the Ministry of Health, Labour and Welfare) was issued, and will be applied to new drug products submitted for approval after April 1 2017. For 24 elements categorized in Class 1 to Class 3, residual quantities in pharmaceutical drug products must be controlled within permissible limits. Although ICP-AES and ICP-MS are used for precise analysis of elemental impurities, X-ray fluorescence spectrometers can be used as an alternative analysis method. This is because they can quantitatively and qualitatively analyze a variety of elements nondestructively, and without chemical pretreatment, unlike ICP-AES and ICP-MS systems. The X-ray fluorescence spectrometry has been adopted as a general method of analysis in the U.S Pharmacopeia and the European Pharmacopoeia. (USP<735>, Ph.Eur.2.2.37)
-
Product
Solar Array Simulator
SAS
-
AMETEK Programmable Power, Inc.
A spacecraft solar array is subjected to large temperature excursions, varying insolation (the amount of sunlight falling on the array), mechanical changes and aging, which substantially effect both its short and long term performance. In order to test the spacecraft's power environment, a cost-effective solution for ground based testing is to utilize a solar array simulator.
-
Product
Reach-In Solar Panel Test Chamber
-
For testing various size solar panels WIEBER designs and manufactures Solar Panel Test Chamber. The test are to be performed according to various standards of ASTM, IEC, UC etc. Solar panels need to pass environmental tests as per IEC and other standards requirements to prove their long term performance and resistance to temperature and humidity extremes. Solor Chamber also known as Solar Photovoltaic Testing Chamber and PV Module Test Chamber.
-
Product
Solar Cell Tester
-
Jiangsu Keyland Laser Technology Co., Ltd.
Features:- Up to standard IEC60904 & JISC8933- 24 hrs continuous working , over 300,000 flash- Siemens PLC system adopted- 10 Parameters display
-
Product
Laser Power And Energy Meters
-
Measure laser power and energy with ease and precision over a huge range of wavelengths, power levels, and pulse energies.
-
Product
RL78 Family of 8/16-bit Ultra-Low Energy MCUs
RL78/I1x
-
The RL78/I1x microcontrollers are part of the RL78 microcontroller family with rich analog integration and support high temperature operation. RL78/I1x is ideal for application specific solutions but also suitable for many general purpose application In the mass market with tough environment operation.
-
Product
Monitoring Solar Panel Strings, DC 30A, Φ10mm
CTF-30-10DC
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Compact, Space-saving, Low Cost DC Current Sensors.・Split-core type, easy to apply to existing circuit.・Easy to use by unipolar +5V power supply.・High speed responsibility – less than 10μsec. 0 rated primary current.・Suitable for monitoring solar panel strings.
-
Product
Energy Analyzer
EP600i
-
The EnergyPro EP600i is portable and easy to use. Perfect for single phase or three phase energy consumption analysis and basic power quality monitoring. It supports standard wiring configurations and comes with a set of 1A - 2500A WideRangeFlexCT ™. The graphics display makes setup very easy and intuitive - you can setup and record data without looking at the manual!
-
Product
Energy & Process Monitor
-
Real time monitoring and reportingComposite system with EMS and PEMSDesired reports like, Doff wise, shift wise, count wise, production, energy, UKGSpeed Vs Kw curve, trends, bar graphs, comparisonsAlerts on higher UKG, lesser production, utilization & power fluctuations.Maintenance alerts based on run hours production cost analysis - Cost Audits - Energy Audits
-
Product
Vernier Energy Sensor
VES-BTA
-
Vernier Software & Technology, LLC
The Vernier Energy Sensor offers an easy way to quantify voltage, current, power, and energy output of small wind turbines and solar panels such as those used in our KidWind Experiment Kits.
-
Product
Walk-In Solar Spectrum Test Chamber
-
WEIBER walk in Solar Spectrum Test Chambers are one of solutions to be utilized in large scale PV testing program. We offer customized as well as standard multidimensional test program for PV modules in reasonable prices. This system delivers the weathering stress representative of long term outdoor exposure.Our flexible system can be designed according to our test requirements, to suit environmental test conditions like volume, temperature, humidity solar radiation intensity and other measuring instruments. It is also called Walk in Solar Radiation Test Chamber.WEIBER solar test system are recognized for superior solar simulation environmental Testing, evaluating outdoor use product reliability, quality & safety. This technology allows for very high concentrations of UV energy without excessive heating of test samples. Custom mounting and cooling can be added depending upon specific material exposure requirements. MHGs (metal halide global lamps) are used as radiation source. Solar spectrum chamber also known as Walk in Solar Simulation Test Chamber
-
Product
Energy Meter
SME 13A
-
SHANGHAI POWOO INDUSTRY CO., LTD
The SME12(13)-A is a single-phase static electricity meter which is integrated the functions of display, sampling, processing for measuring energy. SME12(13)-A Single-Phase Static Electronic Meter is applies for measuring single phase two wire (three wire) AC active energy which frequency is 50Hz or 60Hz. The meter complies with IEC62053 standard.
-
Product
Fully Automatic Solar Cell
Module Laminator-H
-
1. Model: BSL2236OAC-H2. Effective lamination area: 2200mm × 3600mm3. Dimensions: length 17410mm × width 3665mm × height 2164mm4. Heating method: heat conduction oil heating5. Compressed air source pressure: 0.6～0.8MPa6. Working vacuum degree: 100～40Pa7. Evacuation rate: 70L/S8. Temperature control accuracy: ±1.5°C9. Temperature control range: room temperature - 180°C10. Temperature uniformity: effective lamination area≤±2℃11. Lamination chamber height: 30mm12. Evacuation time: depending on the process, it is recommended to take 5 to 8 minutes13. Upper cover stroke: 300mm
-
Product
Solar Cables And Connectors
-
All of our Solar Connectors are thoroughly tested and TUV 1500VDC and UL1000VDC approved. These connectors provide reliable, waterproof and anti-aging features, and are proven to withstand any heavy environmental conditions. Other Solar Connectors typically have a water permeability rating of 66 or 67. Our IP68 rating ensures that our Solar Connectors will hold up in the most severe environmental conditions including sand storms and water submersion up to 3 meters. Our solar connectors are compatible with any solar connectors in the industry. We have designed our connectors to complement other solar connectors as well as replace them. Whether you’re looking for solar connectors to use with your current ones or searching for solar connectors to start a project, our solar connectors will be right for you.
-
Product
Solar Panel Test Chambers
-
Shanghai Morningtest Environmental Chambers Co.,Ltd.
Morningtest customize solar panel test chambers for testing photovoltaic modules to ensure compliance with IEC 61215 and 61646, UL-1703 and other test standards.
-
Product
Energy Saving System
ECO-Vibe neo
-
ECO-Vibe neo has been designed for an eco-friendly vibration test system. The test conditions with a vibration test system depends on a unit under test. Generally, the exciting force required for performing a vibration test can be calculated by the product of mass (e.g. test article, jig, table, etc.) and test acceleration. But, when the required exciting force is smaller than the maximum rated exciting force of the vibration test system, the field power supply that the constant current has to be continuously provided to produce the DC magnetic field constitutes a large part of power consumption compared with the drive power for the moving element. ECO-Vibe neo can reduce the power consumption by choosing the exciting force in this case. In addition, you can enjoy a reduction merit of the running cost from the first year when the system is introduced because initial cost is zero.
-
Product
Long Life Seismic Energy Source
1900LLX-T
-
Output volume of 10 cubic inches to 250 cubic inches. Light weight enough for shallow draught vesselsPowerful enough for blue water seismic surveys. Available with engineered seals for more robust performance.
-
Product
Portable Test Bench for Single Phase Energy Meter
SY2100
-
Hong Kong Songyang Industrial Ltd.
The new SY2100 series Portable electricity meter test equipment, designed from new DIGITAL WAVE COMPOUND TECHNOLOGY and according to International Standard, is newly intelligent equipment for energy meters. The equipment includes voltage/current source & standard meter, operated easily through front panel to preset directly all data of meter under test and test process.
-
Product
Modular Solar Array Simulators
E4360 Series
-
The E4360 Modular Solar Array Simulators accurately simulates the I-V curve of different arrays under various environmental conditions (such as eclipse, spin, rotation, age and temperature). Its small size and high power saves valuable rack space.
-
Product
Solar simulation systems
-
Whatever your application, from an environmental chamber for small components to an extensive array for a complete automobile or aircraft test, EYE / Iwasaki has the experience to provide a solar lighting system customized for your requirements.
-
Product
Pulse energy and power measuring instrument
LEM 2410
-
A touch panel and function keys make this device comfortable and easy to handle. The preamplifiers integrated into the device and the choice of sensor sensitivity allow a wide range of sensor heads to be used. The large graphic display offers space for a variety of display and analysis choices. The digital display can be used for determining the energy, frequency and average power.
-
Product
High Energy Shock Test System
KRD13 series
-
KRD13 series high energy shock test system is specially designed to meet the requirements of military and automotive testing. The system adopts the principle of pneumatic energy storage expansion. By adjusting the inflation pressure, various high-level acceleration tests can be easily implemented in a short stroke.For the high-G classic shock test, it’s equipped with the corresponding shock amplifier to complete high-peak shock test.
-
-
Product
Solar Wafer Transfer Tool
-
Dou Yee Enterprises (S) Pte Ltd
Dou Yee Enterprises Solar Wafer Transfer Tool
-
Product
Energy Meter Calibration
GF312D1
-
Beijing GFUVE Electronics Co.,Ltd.
The instrument is a precision AC energy meter testing instrument, mainly used to test three phase energy meter error on site and measure all various of AC parameters.
-
Product
Energy Probes
RjP-600 Series
-
The RjP-600 Series energy probes integrate the detector and preamplifier in the same enclosure, thereby maximizing signal integrity between the detector and preamplifier. This permits longer cable runs between the probe and instrument, as is often necessary in production environments. Probe specific information, like calibration date and wavelength response curves, is stored in the probe for access by the instrument. Other features include interchangeable filter holders and ¼-20 mounting hole.
-
Product
Non-contact Inline P/N Checker Module For Solar Wafer
PN-100BI
-
*Principle: Photovoltaic effect with the laser diode*Suitable for production line and tranceportation system*Connect to host PC by LAN to send measurement command and data
-
Product
Solar Cell PL/EL/IV 3-in-1 Testing System
VS6841
-
Industrial Vision Technology Pte Ltd.
This luminescence Analyzer integrates a Photoluminescence (PL), Electroluminescence (EL) , and I-V Measurement Technology, has a Device’s PL image, EL image, as well Device’s I-V characteristics in One system. It is being using to quantitatively map Minority-Carrier Lifetime, and to characterize the defect of silicon wafer & solar wafer, and measure the key parameters from solar cell I-V Curve. It is also a useful tool for scientist to develop other methodology & parameters that can be used as a promising technique for online material monitoring and process control.
-
Product
Energy Management
-
Energy Management is a measurement technology to record relevant process factors.
