Filter Results By:
Products
Applications
Manufacturers
-
product
Digital Delay / Pulse Generator
DG535
Stanford Research Systems, Inc.
The DG535 Digital Delay and Pulse Generator provides four precisely-timed logic transitions or two independent pulse outputs. The delay resolution on all channels is 5 ps, and the channel-to-channel jitter is less than 50 ps.
-
product
One Wire Communication Board
MS 1727
- Digital serial bus communication with low speed data over a single line, Both signaling and driving power over a same single signal.- Protocol used in small inexpensive devices. Such as digital thermometer, weather instruments, laptop sub module, authenticate system and some cell phone battery packs.- Always master only initiates the communication and in overall in charge of the network.- Bus communicates with master and slave at a low data rate of 12kbps.- All terminals in the network are communicating by half-duplex mode.- Maximum of 255 nodes in each 1-wire network- Each data transaction will start with 480micro second low RESET pulse.
-
product
Detectors
Teledyne RF & Microwave offers all types of detectors with both analog & threshold designs operating from 10MHz to 26GHz, with excellent power temperature stability.With over 50 ITAR-Free designs, many packaging options and with up to 10nS pulse response, Teledyne is able to offer the right detector for your particular application.
-
product
Signal Generators
SSG3000X Series
SIGLENT’S SSG3000X series of signal generators have a frequency range of 9 kHz to 2.1 GHz/3.2 GHz. They provide normal analog modulation such as AM, FM, and PM. They also provide pulse modulation and pulse train generator. In addition, when used with baseband generator such as SDG6000X, They can generate IQ modulated signals. With their high accuracy and pure outputs, the SSG3000X series is the right choice for R&D, education, and manufacturing.
-
product
Precision Picoprobe™ Micropositioner Probe Holder Kit
PHD-3001A
High Power Pulse Instruments GmbH
*Pulse force and pulse sense fixed pitch and flexible pitch RF probing solution for TLP/VF-TLP/HMM on-wafer measurements using Picoprobe™ Model 10*High peak current capability 80 A (100 ns)*DC – typ. 7 GHz bandwidth*Isolated probe-head ground shield for high pulse sense common mode signal rejection*Including fixed pitch replacement probe tip 50 Ω, right, 100 µm pad pitch*Including fixed pitch replacement probe tip 5 kΩ, left, 100 µm pad pitch*Including flexible pitch clamps plus 10-5k(0502)-125-W-1 and 10-50/30-125-W-1 replacement probe tips*True coaxial high-resolution 80:1 rotary probe-head for accurate probe tip adjustment
-
product
Industrial Tech Laser
Lumentum offers OEM customers the widest variety of laser modules, engines, and components. These diverse lasers deliver a full range of performance with diverse features such as extreme operational performance, proprietary SESAM technology, direct-process fiber connect processes, high pulse-to-pulse stability, the highest stability and reliability, and low noise with excellent beam quality. Our lasers consistently set industry standards for reliability and longevity.
-
product
Short Pulse High-Frequency Laser Marker
LP-RV SERIES
Panasonic Industrial Devices Sales Company of America
The LP-RV Series FAYb Laser Marker features:- Short Pulse 20W Fiber Laser Offers Excellent Mark Contrast On Difficult To Mark Plastics And Various Other Materials- Optional EtherNET/IP Or ProfiNET Interface Adaptor Card- Modular Laser Oscillator System Makes Servicing In The Field Possible - Direct Connection To Panasonic PV230 Vision System For Mark Verification, Auto-Targeting, And Other Machine Vision Functions- Compact IP64-Rated Marking Head For Use In Harsh Environments- Compliant With FDA Regulations, GB Standard, KC Mark, Machinery Directive (Declaration of Incorporation), EMC Directive, RoHS Directive
-
product
0.1Hz-5MHz Functional Generator
MFG-3005
*Frequency range: 0.1Hz~5MHz*Output waveforms: Sine ,triangle, square, positive and negative pulse, positive and negative ramp*Output impedance: 50Ω±10%*Output Amplitude: Not less than 20Vp-p(open circuit)*DC voltage: 0~±10V continuously adjustable*Symmetry range: 90:10—10:90*Rising edge of square: Less than 100ns
-
product
Inductive Proximity Sensors (Square)
SP2
Easy installation, high-speed pulse generator, high-speed rotation control, and more. A wealth of models ideal for limit control, counting control, and other applications. Sensing distance from 1~2/2 ~ 6/ 5~ 12/10~15mm. Housing by PBT with strong structure and acid resisting available.
-
product
Instrument Mainframe
PI-11006
The PI-11006 Instrument Chassis was designed to accommodate the power and noise requirements of some of Pulse Instruments analog instrument cards. These instrument cards, such as the PI-41401, PI-41702 and others supply signal outputs that require more current from the -12 V supply than available in a standard chassis. Therefore this chassis has a larger -12 V power supply that provides 2.5 Amps.
-
product
High Voltage 50 Ω Pulse Generator for CMTI
CMTI-8010A
High Power Pulse Instruments GmbH
The CMTI-8010A is a high voltage 50 Ω pulse generator for static and dynamic common mode transfer interference (CMTI) evaluations of digital isolators according IEC-60747-5-5 and IEC-60747-17.
-
product
Counter DAQ Cards
Counter card series include pulse output, event counting, PWM measurement/output and encoder reading functions.
-
product
WAVEFORM GENERATOR
WFG 600
The multichannel, high voltage, computer controlled Waveform Generator WFG600 is an exceptional instrument designed primarily for experiments on addressing liquid crystal devices and is most suitable for all applications where synchronized trains of pulses with variable width and amplitude are required.
-
product
ATA-500/1000 Auto-Temperatured LED Opto-Electronic
Hangzhou Everfine Photo-E-Info Co., LTD
ATA-500/1000 controls the temperature of the LED, and the photochromatic-electric performance of the LED under different junction temperatures can be measured and analyzed in pulse mode or DC mode on patented software.
-
product
Data Diver
MT-8006B
LCD display for dialing number, Caller ID, Clock and other informationIndicator for determining the Line service and speedHigh impedance monitor for data safe operation without disrupting existing traffic.Smart power saving enables battery life up to 6 months12 phone number memory for speed dialing16 dialing number memoriesTone (DTMF) and pulse operationUp to 32 digits phone number memory for speed dialing keyPre-dialing and last number redial functionPBX pause key, insert a PBX pause in stored numbersTelephone line polarity indicatorsLow battery indicationBacklight functionRJ-11 port for easy test leads changeRinger and voltage LED indicationAngled bed of nails and RJ-11 plug
-
product
Non-contact Conductivity Type (P/N) Checker For Quick Check
PN-50α
*Principle: Photovoltaic effect by light pulse irradiation*No damage and no stain by Non-contact method*Possible to check even oxidized film on wafer surface*Instantly discrimination by optical pulse illuminate
-
product
8-Channel, 100 MHz Counter/Timer/Frequency Meter Function Card
ProDAQ 3808
The ProDAQ 3808 function card, an enhanced version of the ProDAQ 3806 counter/timer function card, is designed to operate in one of three modes: pulse counter, frequency meter, or time interval counter. In the pulse counter and frequency measurement modes, users can process incoming signals of up to 25 MHz on each of the six channels. A time interval counter range is divided into six sub-ranges, covering times from 40 ns to 20000 s with a maximum resolution of 10 ns. For pulse-width measurements, the same ranges apply.
-
product
Pulse generator
9355-1
Solar Model 9355-1 Pulse Generator is designed to provide impulse excitation by means of an injection probe placed around interconnecting cables or power wires. The unit uses a charged transmission line (50 ohms) to generate a pulse with less than 2 nanoseconds rise and fall time, and duration of approximately 30 nS, calibrated in a 50 ohm fixture to deliver up to 5 amperes at a rate of 30 p.p.s. for one minute as required by MIL-STD-461D/E, test method CS115.
-
product
High Precision Fuel Flow Meter
This system measures fuel consumption of an engine operated in steady state with high accuracy.•0.02 to 90L/h and 4500:1 wide range measurement (H type)•Keep the temperature change of the circulation flow passage in the device within ±0.1℃ (variation per 1 minutes) to provide stable measurement.•Pipe arrangement which minimizes air bubbles that enter the system reduced the factor error causes.•Resolution has been improved by using an encoder with 1200P/R (Ten times of number of pulses to the existing model.)
-
product
Premium Data Loggers with 1-4 Channels
Premium Data Loggers for temperature, humidity, co2, atm. Pressure, voltage, current, pulse and 2-state inputs.
-
product
Laser Distance Meters
Sends a pulse of laser light to the target and measures the time it takes for the reflection to return
-
product
Pulsed X-ray technology
Golden Engineering X-ray generators are based on Pulsed X-ray technology. Pulsed X-rays generate a high intensity X-ray burst (pulse) in a very short period of time (10 to 50 nanoseconds depending on the model). The output dose of each pulse is 3-6 mR measured 12 inches from the front of the X-ray generator. The operator varies the overall dose of each exposure by changing the pulse setting. The pulse rate varies from 10 pulses per second to 25 pulses per second depending on the model. The generators can fire up to 200 pulses before a four-minute rest period.
-
product
Pulse Oximeter Simulators
Take control of all your simulations with the next-generation SpO2 pulse oximeter simulator, OxSim Flex. The world’s smallest SpO2 tester now provides complete flexibility in selecting saturation, pulse rate and perfusion index. Users can create customized Preset Simulations for faster testing of oximeter performance and for alarm testing without having to change the monitor’s alarm settings!
-
product
VXI High Precision Timer Counter
VX2210
The VX2210 is a high precision, 9 digits, 100MHz Timer/Counter for high performance measurements. The two input channels (A and B) can be used independently and providing capabilities needed for electronic test applications. Counter functions include frequency, period, pulse width, time interval, rise and fall time and totalize measurements. An optional third channel (C) can be used for frequency measurements of up to 1.3GHz.
-
product
Programmable Low-Ohm Meter
DU5210/5211
Delta United Instrument Co., Ltd.
20m ~ 2Mtest range, 0.1% accuracy Provided Level and Pulse measurement modes, can be lower temperature influence in Pulse Mode Provided HI/LOW limit and BIN Sorting comparator function, to meet your needed 100 sets of memory, can be saved test parameter and comparator setting, easy to use. Auto Calibration Program Function, to easier your calibration procedure. (Specificity calibrator needed) Cover up free, system firmware upgrade can be update via RS-232, easy to maintenance High speed FADC, max. test speed up to 80 meas./sec, faster your automation equipment 240*64 Graphic LCD display, can be read the reading clearly and easier. User friendly programmable interface, easy to use Provided RS-232C and Handler combinatorial interface option, to meet your needed
-
product
Ultrasonic Flowmeter
F5
Gentos Measurement & Control Co.
F5 ultrasonic flowmeter uses the latest digital technology and low-voltage broadband pulse transmission. The instrument can tolerate a small amount of bubbles or suspended solids in most industrial environments.
-
product
Embedded Antennas
Pulse’s broad customizable portfolio of embedded antenna solutions will have your device connected regardless of the circumstances. Pulse embedded technologies results in robust board-mounted antenna designs making them exceptionally suitable across many solutions. Our in-house manufactured embedded antenna line; ceramic chip, patch, stamped metal, FPC, composite antennas and active GNSS antennas are some of the world’s smallest, compact and most efficient. Our embedded antenna line is manufactured for a variety of applications and frequencies such as Cellular, WiFi, BT, ISM, GPS/GNSS/Bediou and many more. You can search through our selection of catalog embedded products using the table below to find the right product for you.
-
product
Counter/Timer Board
USB-CTR-15
The USB-CTR-15 is an ideal solution for adding portable, easy-to-install, counter/timer capabilities to any PC or embedded system with a USB port. This board is packaged in a small, rugged, industrial enclosure and features 15 independent 16-bit counter/timers. The unit is a true USB 2.0 device, offering the highest speed available with the USB bus. It is fully compatible with both USB 1.1 and USB 2.0 ports. The unit is plug-and-play allowing quick connect/disconnect whenever you need additional counter/timer devices on your USB port. The USB-CTR-15 can be used for a wide variety of measurement applications including event counting, frequency measurements, position measurement, pulse counting, pulse-width modulation and pulse generation. The OEM version provides just the board without the enclosure or external screw terminal board and is ideal for a variety of embedded OEM applications.
-
product
Detectors
Teledyne Microwave Solutions (TMS) offers all types of detectors with both analog & threshold designs operating from 10MHz to 26GHz, with excellent power temperature stability. With over 50 ITAR-Free designs, many packaging options and with up to 10nS pulse response, TMS are able to offer the right detector for your particular application.
-
product
Speed Switch Sensor & System Testing Device
The SpeedMaster with Pulse Pilot provides independent, real time, and complete verification of an entire speed monitoring system to ensure that alarms and shutdowns are working as expected.
