PXI Serial Interfaces
See Also: Serial Interfaces
-
Product
PXI / PXIe Backplanes
-
PXI (PCI eXtensions for Instrumentation) is a PC-based bus platform for measurement and automation systems. PXI uses commercial PC-based PCI bus technology while combining rugged CompactPCI modular packaging, as well as key timing and synchronization features. While derived from cPCI, PXI adds the timing and synchronization features, among other things, that were not present in cPCI.
-
Product
GSP-2B Test System Interface Probe
GSP-2B
ICT/FCT Probe
Current Rating (Amps): 5Average Probe Resistance (mOhm): 35Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 125Full Travel (mm): 3.18Recommended Travel (mil): 125Recommended Travel (mm): 3.18Overall Length (mil): 845Overall Length (mm): 21.46
-
Product
Optical Head Interface
N7749C
-
The N7749C optical head interface can control two or four 8162-C series optical power meter heads. Readout is supported over LAN and USB interfaces with a built-in web-browser GUI and the SCPI command set common to Keysight optical power meters.
-
Product
Interface for Two Dual Redundant 1760 Channels
EXC-1553ExCard/Px-1760
-
This credit card sized interface supports up to two dual redundant 1760 channels and is compatible with all common variations of MIL-STD-1760 providing a wide range of features normally found only on full size testers.Multi FunctionEach channel of the EXC-1553ExCard/Px-1760 operates simultaneously as a Bus controller and/or multiple (up to 32) Remote Terminals, or as a Triggerable Bus Monitor. The card supports error injection and detection. The card’s small size and compatibility with notebook computers make it the perfect solution for performing system simulation of the MIL-STD-1760 bus, in the lab and in the field. Single Function Each channel of the EXC-1553ExCard/PxS-1760 operates either as a Bus Controller, Remote Terminal, or Bus Monitor.The EXC-1553ExCard/Px-1760 and EXC-1553ExCard/PxS-1760 cards are supplied with C drivers, including source code, Merlin+ Windows software and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application.Note: Some laptops do not supply the average and peak power voltages required by the ExpressCard specification. The EXC-1553ExCard/Px-1760 may not function properly in these laptops.
-
Product
Microphone Pre-Amp Audio Interfaces
-
Analog Devices mic pre-amp audio interfaces provide a high fidelity, high performance solution for audio products. Specifications for this family include ultralow 1.5 dB noise figures, 140 dB gain range, and high gain capability. Operating in an extended industrial temperature range of –40°C to +85°C, this portfolio of mic pre-amp audio interfaces supports many applications, including precision instrumentation, active filters, low noise amplifier front ends, surveillance systems, computerized voice recognition, and a variety of other industrial and consumer products. As the first choice for serious audio engineers, Analog Devices mic pre-amp audio interfaces can give your applications the performance needed to meet the most demanding specifications.
-
Product
PCI 16 Isolated Input Digital Interface (10-30V)
8006H
-
Optimized for sensing up to 24V inputs, the 8006H PCI digital I/O interface provides 16 optically isolated inputs for connection to devices including sensors, switches, push buttons, and other user inputs.
-
Product
3U CompactPCI® RS-232/422/485 Serial Communication Card
MIC-3955
-
The MIC-3955 is a low power 4-port or 8-port RS232/RS422/RS485 serial board with 3U CPCI form factor and is based on the EXAR PCI controller. MIC-3955 is PICMG 2.0 Rev. 3.0 compatible. Rear board module are named MIC-3527XX. The MIC-3955 supports front IO or rear IO with 4-port and 8-port, and every channel is independent.
-
Product
PXI Breadboard Module, 2-Slot, No Connector
40-220A-102
Signal Module
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
Product
Nano Interface Unit
NIU2A
-
NAI’s NIU2A contains an integrated power supply, two function module slots and an optional ARM® Cortex®-A9 processor. This small, low-power unit is ideally suited for rugged military, industrial, and commercial applications. It delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems — in less time, with NO NRE.
-
Product
4-TAP PXI Express JTAG Controller
PXIe-1149.1/4E
Controller
The PXIe-1149.1/4E is a highperformance, multi-feature boundaryscan controller for multi-TAP and concurrent JTAG test and in-system programming. Featuring a high-speed PXI Express (PXIe) interface with four independent and configurable Test Access Ports (TAPs) along with direct serial programming capability, the PXIe- 1149.1/4E enables of boundary-scan integration with PXIe systems.
-
Product
SparkFun USB UART Serial Breakout
CY7C65213
-
The CY7C65213 USB to UART serial breakout is designed to provide users with a means to access all available I/O pins on the IC, and to provide a 6-pin UART header that is compatible with other SparkFun breakout boards. This breakout has a microUSB connector and other support circuitry to get the IC quickly up and running.
-
Product
Serial Communications Card
104-ICOM-2S
-
The Model 104-ICOM-2S Serial Communications Card can be installed in a PC/104 stack and provide effective communication on long lines in noisy environments. Data lines are opto-isolated from the computer and from each other to assure communication even when large common mode voltages and noise are imposed.
-
Product
3U CompactPCI Serial 7-slot SSR w/ RTM w/ Ethernet
1CPCIS-307-R110
-
3U CompactPCI Serial Backplane with 7 CompactPCI S.0 slots, system slot right, with rear IO: 1x CompactPCI S.0 CPU slot, 6x CompactPCI S.0 peripheral slots, with connectors for RTMs, Ethernet single star from system slot to all peripheral slots.
-
Product
PXI 15W Programmable Resistor Module
40-254-110
Programmable Resistor Module
The 40-254-110 (PXI) and 42-254-110 (PXIe) are programmable resistor modules with 1 channel which can be set between 1Ω and 31Ω with 0.125Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
Product
PXI 2A Multiplexer, 4-Bank, 4-Channel, 8-Pole
40-614B-009
Multiplexer Module
This 4-bank, 4-channel, 8-pole version is part of the 40-614B High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
Interface And Signal Processing Units
-
The interface and signal processing units extend the field of application of Micro-Epsilon sensors. The interface modules are used to convert sensor signals into digital or bus-compatible interfaces. This enables interfaces such as USB, RS422, Ethernet/IP, Profinet and EtherCAT for numerous sensors. The signal processing units are also used to record several sensor signals, to calculate and output them together. This is necessary, for example, for planarity measurement or thickness measurement.
-
Product
Fibre Channel XMC Interface Module
XMC-FC4
-
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Supports DMA for high speed streaming of data to/from the board - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
Product
Nano Interface Unit
NIU1A
-
NAI's NIU1A is a nano unit with an integrated power supply, one function module slot, and an optional ARM Cortex-A9 processor. This small, low-power unit is ideally suited for rugged military, industrial, and commercial applications, and delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in less time, with NO NRE.
-
Product
PXI RS232 Interface Galvanic Isolation
PXI‑8432/4 - OTP2-Modul-Nr196
-
The PXI‑8432/4 module is a high-performance, dielectric-proof interface for high-speed communication with RS-232 devices. The module offers data transfers via the high-speed DMA interface, multithreading and multiprocessor support. NI serial ports appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
PXI 2A Multiplexer, 4-Bank, 32-Channel 1-Pole
40-614-006
Multiplexer Module
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
Product
Universal PCI, RS-422 Or RS-485 Serial Interface Cards
LPCI-COM422-8 and LPCI-COM485-8
-
These are eight-port, asynchronous, serial communication cards designed for use on the PCI bus. They support RS-422 or RS-485 communications. These cards offer the best combination of high-density and high-speed communications in a low profile form factor. The cards meet the MD2 Low Profile PCI Bus Specification and can be used in applications where space is at a premium, such as thin-client servers and high-density rack-mount servers. The LPCI line has been designed for use in retail, hospitality, and point of sale systems as well as the gaming and defense industries.
-
Product
Optical-Electrical Converter - PXI
O2E 1000 – 1400 Series
Optical / Electrical Converter
The O2E is a high bandwidth, broadband optical to electrical converter.Available in a range of configurations; choose from 1 or 2 channels, AC or DC coupling and various conversion gain and operating wavelength ranges.
-
Product
TSCOE4 Operator Interface Software Module
-
The TSCOE4 Operator Interface provides a graphical user interface for the operator or the implementer in a production environment. It permits selecting the test sequence and supports parametrization of the test. During the test sequence, the current measurement values are displayed in relation to the relevant limits and the pass/fail evaluations for each individual test. After completion of the test sequence, the global test result is visualized.In addition, there are online statistics available to the user, which show the measurement value distribution within the current batch.The editor which is supplied with the product makes it possible to adapt the user interface language to any new deployment location. Several languages – German, English and Chinese – have already been implemented and are available out of the box.
-
Product
PXI 13 x DPDT Power Relays
40-130-102
Relay
Pickering Interfaces 40-130 DPDT Relay Modules are suitable for applications where ordinary reed relay modules require additional current/voltage capacity. It is available in a choice of 8 and 13 relay versions and has voltage handling up to 220VDC/125VAC and current handling to 2A . Connections are made via a front panel mounted 50 or 78 pin D-Type connector.
-
Product
PXI Dual 32x4 Matrix 1-Pole Switching
40-534A-021
Matrix Switch Module
Typical applications include signal routing in Functional ATE and data acquisition systems. These PXI matrix modules are constructed using high reliability sputtered Ruthenium reed relays, offering >109 operations to give maximum switching confidence with long life and stable contact resistance. Larger matrices may be constructed by daisy chaining the common signals from multiple PXI modules.
-
Product
4- or 8-Port Serial Module
Emerald-MM-8EL
-
The Emerald-MM-8EL-XT is a family of high performance PCIe/104 "OneBank" serial I/O modules offering 4 or 8 multiprotocol serial ports with software-controlled configuration and optional opto-isolation.
-
Product
PXI Voltage Amplifier, +/-33V
41-650-001-S1
Amplifier
A 5 channel voltage amplifier ideal for increasing the output voltage from other PXI modules, enabling users to easily generate the signal voltages commonly required in applications such as automotive test.
-
Product
Simulator / Analyzer / Tester PCI BUS Interface Card
CIC301 - MIL-STD-1553
-
The CIC301 is a full-featured, high performance, Dual Redundant MIL-STD-1553 A/B serial bus Simulator Analyzer Tester designed as a plug in card for PCI backplane. The CIC301 includes full error injection and can operate in independent or simultaneous mode as a Bus Controller, multiple simulated Remote Terminals and full/selective Monitor. Its data structure can be changed on the fly without interrupting the processor for real time operation. The active monitor stores, time tag and annotates bus traffic with the message type and any detected errors. Stored words are annotated with a break down of the word error.
-
Product
PXI Optical Switching
-
Pickering's range of PXI optical switching modules include high performance multiplexers and insert/bypass switches. MEMS (Micro Electro-Mechanical Systems) switch technology offers higher performance and longer operational life compared to conventional prism based optical switching
-
Product
HS1760/MIL-STD-1760E Network Interface Controller for PCI Express
PCIe-1760-NIC-FP
-
Avionics Interface Technologies
Configuration Variants available: PCIe-HS1760-NCNT: One NC Node and One NT Node, PCIe-HS1760-NCNC: Two NC Nodes, PCIe-HS1760-NTNT: Two NT Nodes - SAE AS5653-Compliant Network Controller/Network Terminal NIC - Unsolicited data path for handling Fibre Channel link service or non‐FC-AE‐1553 traffic - Supports DMA for high speed streaming of data - 75 Ohm single‐ended or 150 Ohm Differential coax interface – TNC connectors - Each port supports 1.0625 Gbps speed - ANSI C API interface for both NC and NT - Device driver support: Windows, Linux, & VxWorks - Quad (4) port board available on request
