Rf Power Amplifiers
See Also: RF Power, RF Amplifiers, RF Power Meters, RF Power Sensors
-
product
RF Signal Generators
Value for money RF signal generators with frequency capability from 1.0GHz up to 6.0GHz.
-
product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J0
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
product
Power Probes
RkT Thermopile Series
The RkT Series thermopile power probes are ideal for measuring Nd:YAG, CO2, and other mid-power lasers. The probes are designed to withstand average power densities up to 20kW/cm2 (15MW/cm2 peak pulse power density). The flat UV to far-IR spectral response allows the probes to measure broadband sources as well. Measure the power of cw sources or the average power of sources pulsed at 5Hz or greater.
-
product
RF Directional Coupler
ZDC9-20C1-40G-1661
Frequency 1000~40000MHz, Coupling 20dB, 20W, Connector 2.92 Female
-
product
Power Supply
Model 62-4PS
FEATURES: Supports All 62 Series Converters; Internally Regulated +12, - 12 & +5 Volts; 110 & 220 Units. The Model 62-4PS is a small wall mount that is used to supply power to any of the Series 62 Interface Converters. The 62-4PS contains internal regulators to provide +12, -12 and +5 Volts. Note that the 220 Volt unit is not a wall mount.
-
-
product
Analog Control Variable Gain Amplifiers (VGAs)
Analog Devices voltage controlled variable gain amplifiers provide continuous gain control over a wide dynamic range for a variety of audio and optical frequency bands. Our VGAs improve the dynamic range of a circuit by allowing users to adjust a signal’s amplitude in real time, which is invaluable for ultrasound, speech analysis, radar, wireless communications, and instrumentation-related applications.
-
product
Power Supplies
VP SERIES
Crafted for quality, performance and incredible value. This entry-level solution gives you everything you need in a power supply. No twinkly lights or glittery paint jobs - a 120 mm fan for effective and quiet cooling, dual +12V rails for amazingly stable power and heavy-duty protection circuitry for peace of mind, no matter how demanding your system. And it comes with all the assurance of Antec's AQ2 Antec Quality 2 year limited warranty. All the features, none of the waste: for builders that are strictly business, the VP550F is strictly power.
-
product
GHZ-Wideband Amplifiers
Ultra-wide bandwidth from 10 kHz up to 2.5 GHzGain up to 60 dB (x 1,000)Transimpedance gain with photodetectors up to 50,000 V/AVery low input noise down to 310 pV/√Hz (6.2 pA/√Hz)Integrated DC-current path for biased photodetector applicationsTwo identical signal outputs (HSA-Y series)DC-monitor output (HSA-Y series)
-
product
Amplifiers
Amplifiers are used to amplify the energy output of photodetectors as well as convert their electrical signal for a number of illumination measurement or spectroscopy applications. Amplifiers are digital systems that amplify the low electrical current transmitted by photodetectors to easily detectable levels. Amplifiers also convert photodetectors' electrical current into voltage so that their signal may be read by other digital devices. Amplifiers are indispensable for nearly any light measurement applications by greatly increasing the usability of a detector system.
-
product
Power Dividers
Corech Microwave’s Power Dividers also called power splitters, frequency ranges from DC -67 GHz, featured with ultra wideband, multi ways and high power options. 2/3/4/5/6/8/10/12/16 ways designs are available, low insertion loss and high isolation.
-
product
Amplifiers
Amplifier is designed to be used in conjunction with optional modules and can be confiugured for up to 8 inputs and 8 outputs. 9000 series modules as well as existing 900 series input modules can be used. The more appropriate modules can be selected depending on applications. Since it comes with two 60W power amplifiers, it can individually perform multi-origin braodcasts. It is equipped with singnal processing and control functions necessary for sound reinforcement, permitting all parameters to be set at the mixer. Settings data can be stored inside the unit and called up using the keys on the front panel.
-
product
RF Safety Monitoring
MVG EME Guard Plus
The EME Guard Plus is designed to record EMF exposure near antennas while continuously monitoring potential over-exposure. Lighter than the previous model, the EME Gaurd Plus makes it easier for workers to wear on the job. The longer battery life and extended memory capacity enable more measurements to be recorded.
-
product
C-Band Separate Raman Fiber Amplifier
RFA5000
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
-
product
DC Blocking L-Band Splitters, RF Power Dividers
INSTOCK Wireless Components, Inc
INSTOCK Wireless offers DC-blocking power divider / combiners optimized for L-band power splitting applications. Standard configuration includes DC pass on one port to power a remotely located active antenna. Additional models available blocking DC to all ports. All models pass the 10 MHz reference signal through all ports.
-
product
RF Voltmeter
9240
The 9240 series is the latest addition to Boonton’s popular 9200 series of RF voltmeters. It combines accuracy, smart probes, and operator features that have never before been available in its price range. It is simple to use on the bench, and comprehensive enough to integrate into an ATE system.
-
product
Amplifier Module
LNAM-LPA
We offer an evaluation board and case for the LNAM-B and LNAM-FBX modules. This Laboratory PreAmplifier (LPA) solution is powered by a switch-mode power supply and gives access to the LNAM in- and outputs via BNC sockets.
-
product
RF Terminators
Typically placed at the end of a transmission line and is designed to match the cable's AC impedance.
-
product
Power Transducer
Beijing GFUVE Electronics Co.,Ltd.
Devices capable of transforming or converting a certain type of input energy into another different from the output, they serve to obtain information from physical and chemical environments to obtain electrical signals or impulses and vice versa.
-
product
Power Supply
Rishabh Instruments Pvt. Ltd.,
1Phase, 115-230Vac I/P& 24Vdc 384 to 480 W O/p, Adjustable o/p voltage range 22 – 27 Vdc. High efficiency ≥92% & compact size (w-h-d) 85x120x140 mm & DIN Rail Mountable
-
product
Digital Quad-Phase "DSP" Lock-In Amplifier -
eLockIn203
The eLockIn203 can be used as spectrum analyser, as oscilloscope, as sinus generator or as measurement control system.
-
product
Millimeter Wave Amplifiers
Ducommun offers Low Noise (ALN), High Power (AHP), Full Waveguide Band (AFB) and General Purpose (AGP) amplifiers to cover the frequency range from 18 to 96 GHz. These amplifiers utilize thin-film and microelectronics manufacturing techniques and are discrete and/or MMIC PHEMT devices based. These amplifiers feature low noise, high output power, single DC power supply and wide operation temperature range. The amplifiers are offered in two categories, standard and custom-built. Both standard and custom-built amplifiers are equipped with various RF interface, including standard waveguide or coaxial connector for convenient system integration. The optional input and output integrated isolators are available as an option to further improve the port return loss.
-
product
Isolation Amplifier Digital Output
This coupler is an optically coupled isolation amplifier that uses an IC with a high-accuracy sigma-delta A/D converter and a GaAIAs light-emitting diode with high-speed response and high luminance efficiency on the input side, and an IC with a digital signal (MDAT, MCLK) output function on the output side. This coupler is designed specifically for high common mode transient immunity (CMTI) and high linearity (nonlinearity) applications, making it ideal for current sensing in motor drives.
-
product
RF Reference Source
96040A Series
The 96040A RF Reference Source enables you to simplify your RF calibration system by replacing many of the instruments and accessories that make up your current system.
-
product
Bluetooth RF Test System
FRVS
FRVS is recognized by the Bluetooth SIG as a validated test system for qualification testing of products to Bluetooth BR/EDR and low energy RF test specifications.
-
product
Shortwave Power Amplifier
OM2501A (OM3501A)
The OM Power model OM2501A and OM3501A are designed for all short wave amateur bands from 1.8 to 29.7 MHz (including WARC bands) and all modes. OM2501A is equipped with a FU728F or GU84B ceramic tetrode and OM3501A is with GU78b ceramic tetrode.
-
product
Distribution Amplifier
AVLINK TECHNIC TAIWAN CO., LTD.
Is a device that accepts a single input signal and provides this same signal to multiple isolated outputs.These devices are important because they allow a signal to be distributed to multiple destinations without ground loops or signal degradation. They are used for a number of common engineering tasks, including multiple amplification, cable television, splitting monitor and front of house mixes, and "tapping" a signal prior to sending it through effects units to preserve a "dry" signal for later experimentation.
-
product
Power Transformer
Transformer turn ratio meter is special designed for power transformer (single phase & three phases) and instrument transformer testing, suitable for testing in substation, transformer manufacturer, meter manufacturer. It helps to detect faulty transformer winding and tap changer position. It’s fully automatic device, can recognizes winding connection and vector group number of transformer winding. The user only need connect measuring cable and press start button and come out the test result.
-
product
Low Voltage DC / Battery Powered High Voltage Amplifiers
WMA-005 And WMA-005LF
The Falco Systems WMA-005 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-005LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
product
Amplified Photodetectors
Hinds Instruments' photodetector modules are specifically designed for use with high frequency optical signals including those generated in Photoelastic Modulator (PEM) applications.
