Wafer Probers
bring the wafer in contact with the set of wafer probes.
See Also: Probers, Wafer, Flying Probes, Thermal Chucks
-
Product
Full Wafer Contact Test System
Fox 1
-
Unique cartridge technology uses full-wafer contactors combined with parallel test electronics to achieve single touch, full-wafer test
-
Product
Flying Prober Test System
QTOUCH1404C
Test System
Qmax Test Technologies Pvt. Ltd.
The Prober Test System is capable of movement in XYZ directions with fixed angle (θ) and dual probe heads (further expandable up to 4 ) . The system has in-built high resolution Vision Camera for easy monitoring of probe needle contact. The prober supports automatic fiduciary recognition. The system has built –in linear encoders to achieve higher precision.
-
Product
Wafer Bonder
AML
-
Wafer bonding has found many applications in the field of MST, MEMS and micro engineering. These include the fabrication of pressure sensors, accelerometers, micro-pumps and other fluid handling devices. The process is also used for first-order packaging of silicon microstructures to isolate package-induced stresses. The OAI AML Wafer Bonder facilitates both the alignment and bonding to be performed in-situ, in a high vacuum chamber. For anodic bonding the wafers are loaded cold and heated in the process chamber. For high accuracy alignment the wafers are aligned and brought into contact only after the process temperature has been reached, thus avoiding differential thermal expansion effects which can compromise alignment. The AML Wafer Bonder is excellent for anodic bonding, silicon direct and thermal compression bonding applications. These features enable the bonder to be used with virtually any processing tool.
-
Product
Semi-Automatic Contactless Wafer Detector
NCS-200SA
-
Semi-Automatically, non-contact measurement of wafer thickness, TTV ,bow,Point and flatness.Portable and easy to set-up, the Proforma 300/G measures all wafer materials including Silicon, Gallium-Arsenide, Indium-Phosphide and wafers mounted to sapphire or tape.the powerful software can test all the data above within several seconds,all the design according to SEMI standard and the ASTM,make sure the data can be easily unify. the system can used for several sample size,like 75 mm, 100 mm, 125 mm, 150 mm, 200 mm
-
Product
Contactless One-Point Wafer Thickness Gauge
MX 30x
-
The MX30x series are manual one-point Thickness gauges for silicon wafers.
-
Product
Wafer Defect observing instrument
HS-WDI
-
Application■Semiconductor wafer■Solar wafer■Solar Cell■Thin-film Cell
-
-
Product
Wafer Inspection System
-
JRT Photovoltaics GmbH & Co. KG
In close cooperation with well-known providers of inspection systems, we provide modular systems for quality control and classification of raw wafers.
-
Product
Contactless Wafer Gauge for Resistivity, Thickness
MX 60x
-
The MX60x series measure Resistivity or Sheet Resistance of silicon and other materials.
-
Product
Non-contact Measurement Wafer Sorting System (Belt Drive Tranceportation)
NC-6800
-
*Non-contact measurement of resistivity, thickness and conductivity (P/N)*Number of cassette station can be changed by customers request*Eddy current method for resistivity, Electric capacitance method for wafer thickness*Temperature correction for silicon wafer function
-
Product
Wafer/Dicing Frame Prober
WDF 12DP+
-
The WDF 12DP is a prober/handler capable of transporting and testing standard 300-mm wafers and dicing frames without need of a changeover kit. To support multiple tests after dicing, it has a special positioning function that differs from former types, as well as image-processing functions such as wafer level packaging.
-
Product
Bare Wafer Inspection System
LS-6700
-
Hitachi High-Technologies Corp.
High sensitivity (50nm:Bare). High accuracy for COP/CMP discrimination (85%). High throughput (80 wph @300mm).High positioning accuracy (+/-30m). Wafer Size 300mm / 200mm.
-
Product
High Resolution Wafer Thickness & Thickness Variation Gauge
MX 10x series
-
The MX10x series measure thickness and thickness variation on silicon wafers. It has a resolution of 10 nanometers and can be adapted to different thickness ranges within a few seconds.
-
Product
Wafer Test
-
WinWay’s commitment to technology, quality and service ensures our interface solutions go above and beyond to exceed your expectations. Our products and services have a proven track record of delivering customer success in semiconductor testing. The Company offers comprehensive test interface solutions ranging from wafer-level test, package-level test to thermal management.
-
Product
Wafer Analyzer
RAMANdrive
-
RAMANdrive is the specialized Raman microscope for wafer analysis equipped with our dedicated 300 mm stage. RAMANdrive gives you an ultra-fast, highest resolution analysis of the whole wafer with unique stability and accuracy
-
-
Product
Wafer ESD Tester lineup
-
Hanwa Electronic Ind. Co.,Ltd.
◆Correspond to 300mm Wafer. This tester can measure LED or the large sizes Wafer, such as a system LSI. And Zap of HBM/MM can be performed. The Automatic destructive judging by V/I measurement can also be performed after Zap.◆Waveform guarantee in Zap needles. HED-W5100D carries out the calibration before shipment in the place of Zap needles. Therefore, Correlation of the Result of a Package Device becomes clear easily.◆Correspondence to Standards This Tester corresponds to the Standard of JEITA, ESDA, and JEDEC. A Zap unit adopts the plug-in system and also has the waveform of Customer's requests.◆Connection with TLP This Tester is the best for TLP Testing with deep relation of ESD. The protection circuit of a device with an ESD problem is investigated.
-
Product
Wafer Analysis Systems
Tropel®
-
Corning Specialty Materials has a long heritage of providing solutions to semiconductor equipment manufacturers. The Tropel line of wafer analysis equipment enables measurement of wafer substrates from 2” to 450mm regardless of material type and surface finish.
-
Product
Automated Semiconductor Wafer Optical Inspection and Metrology
SITEview Software
-
Microtronic SITEview Software is designed from the end-user operator’s perspective and is easy to use, fully featured, and modular. Applications include visual wafer inspection, OCR sorting, wafer defect review, second optical inspection, image storage and retrieval, laser marking, microscope interface, and GEM/SECS II communication and seamlessly integrates with EAGLEview, MicroINSPECT and MicroSORT.
-
Product
Inline Wafer Electrical quality Inspection
ILS-W2
-
the Ultimate Wafer Electrical Quality Inspection Unit for Wafer Inspection Systems
-
Product
Wafer Demounting And Cleaning Machines
-
Demounting and cleaning to high throughput fully automatic ingot after cutting in the slicing machine and wire saw.
-
Product
Wafer Inspection System
AutoWafer Pro™
-
AutoWafer pro is our most advanced ultrasonic equipment for detecting defects in bonded wafers in a production environment, providing fast, high-resolution scanning of 200mm and 300mm bonded wafers.
-
Product
Wafer Back Side Cooling System
GR-300 Series
-
The GR-300 Series can control gases used to cool the back side of wafers that are fixed in position by an electrostatic chuck system.The stability and accuracy of the GR-300 makes it ideal for controlling the flow of Helium and Argon in wafer cooling systems.
-
Product
Fully Automatic 4 Point Probe System for Silicon Wafer
WS-8800
-
*Measurement of resistivity, thickness, conductivity(P/N) and temperature*Tester self-test function, wide measuring range*Thickness, measurement position and temperature correction function for silicon resistivity*Number of cassette station can be changed by customers request*Host (CIM) communication and SMIF or FOUP compatible
-
Product
WDXRF Wafer Analyzer
2830 ZT
-
The 2830 ZT wavelength dispersive X-ray fluorescence (WDXRF) wafer analyzer offers the ultimate capability for measuring film thickness and composition. Designed specifically for the semiconductor and data storage industry, the 2830 ZT Wafer Analyzer enables the determination of layer composition, thickness, dopant levels and surface uniformity for a wide range of wafers up to 300 mm.
-
Product
2D/3D Wafer Metrology System
7980
-
Chroma 7980 provides accurate and reliable profile information. 7980 adopts new BLiS technology and specially designed platform to achieve 2D/3D nanoscale measurement.
-
Product
Wafer Inspection System
INSPECTRA® Series
-
INSPECTRA® series meet the requests of 100% automatic inspection with high speed and high specifications from front-end to back-end of semiconductor processing. INSPECTRA® series are wafer inspection systems with high speed and high sensitivity. Our original "Die-to-Statistical-Image" comparison method achieves the target defects detection controlling process variation and overkill.
-
Product
Photonics Wafer Probing Test System
58635
Test System
The advancement of the photonics device technology continues to enable broader and more demanding applications in the industry.
