Audio Test
See Also: Audio Testers, Audio Test Systems
-
Product
RSE Wireless EMC Spurious Emission
TS8996
Test System
The R&S®TS8996 RSE test system is designed for EMI and radiated spurious emission testing on wireless devices in semi-anechoic or fully anechoic chambers. The modular design makes it easy to extend the system to include new communications technologies. Typical devices under test include mobile phones or radio sets along with radiated measurements of other short-range devices. Standards require a wide range of test setups and a wide and high frequency range (up to 40 GHz). ESW or FSW frequency ranges are extended up to 325 GHz with option B21 using receive units TC-RSE for 5G FR2. Dedicated RSE test routines are also covered for this frequency range.
-
Product
IOL & Power Cycling Test Systems
Test System
Our IOL & power cycling systems increase measurement quality and throughput and reduce testing costs on an open platform. The focus is on seamless monitoring and precise determination of all parameters of each DUT. In addition, the systems are equipped for the special requirements of wide-bandgap technology.
-
Product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196C
Test Fixture
The 16196C surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results - reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement - now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
Product
VLSI Test System
3380D
Test System
The 3380D/3380P/3380 test system have 4 wires HD VI source and any-pins-to-any-site high parallel test (multi-sites test) functions (256 I/O pins to test 256 ICs in parallel) that can meet the upcoming higher IC testing demands.
-
Product
Automatic Test System
Test System
Automatic Test system is the ultimate solution for power electronic testing. The system includes a wide range of hardware choice such as AC/DC Sources, Electronic Loads, DMM, Oscillate Scope, Noise Analyzer and Short /OVP Tester. This flexibility combined with its open architecture software platform-PowerPro III, gives users a flexible, powerful and cost effective test system for almost all types of power supply testing.
-
Product
Universal Test System
LEON System
Test System
A universal ICT, FCT, ISP and Boundary Scan platform.Based on the ABex platform, which directly integrates Konrad analog bus technology and PXI/PXIe in one chassis, the LEON platform can be configured to solve various test challenges. Due to this architecture only one system provides the complete test flow combining ICT, ISP, Boundary Scan and FCT.Various form factors and configurations allow a perfect combination between cost, speed and test coverage. The modular architecture provides the possibility to reconfigure or upgrade the systems based on your test needs.The LEON System software provides a powerful development and test execution environment which directly supports NI TestStand. All systems and components could be integrated into third party software using supplied APIs.
-
Product
Automated Aerospace and Defense Test
test
Obsolescence management, evolving RF requirements, and design for test (DFT) challenges every test organization in the aerospace and defense industry. Organizations are transitioning from rack-and-stack box instruments and closed-architecture automated test equipment (ATE) systems to smarter test systems built on a modular platform that scales to meet current and future needs.
-
Product
High Speed Test Bench
AT444
Test Platform
AC motor with mechanical multiplying gearbox test benches allow precise programming of all drive parameters required for accurate rotating devices test.The use of special high-speed bearings, mechanical components and parts wear resistant leads to a large life. The supply includes the electronic drive and control as well as the entire oil cooling unit.
-
Product
Standardize Production Test Software For PCBAs And Electronic Devices
test
The vast majority of test project man-hours are spent on software development, so the choices that teams make in software tools and architecture have significant impact on deployment schedules. Standardizing software across a team or organization increases both efficiency and proficiency, lowering the risk of missed deadlines and improving test quality and reliability. Test software must:
-
Product
Regenerative Battery Pack Test System
17040E
Test System
High-power testing equipment up to 1,700V/ 4800A/ 1.2MW Multiple safety protections for personnel safety risk management and control of battery testing Flexible Integration for automated battery verification solutions
-
Product
Display Driver Test System
T6391
Test System
High-resolution flat-panel displays (LCDs / OLEDs) are becoming increasingly integrated. It is common for today's display driver ICs (DDIs) to contain a multitude of logic/analog circuits to manage advanced operations including touch-sensor functions. At the same time, the rapidly growing applications of LCDs / OLEDs in mobile electronics are driving demand for DDI's with smaller sizes and greater capabilities. These factors present serious IC-testing challenges. ADVANTEST's T6391 system is designed to address these needs along with DDIs' increasing number of pins and faster interfaces.
-
Product
Audio/ Video
Audio Analyzer
Our experts/ physicist can help you in the Implementation of your algorithms including BPR, NUC , Edge Detection and movement analysis algorithms.Our development environment is based on C++ and LabVIEW libraries or tools such as Vision Builder for Automated Inspection from National Instruments.
-
Product
Wireless Device Test
test
New wireless standards, in addition to rising wireless usage, are increasing wireless device complexity while lowering price expectations. To counter rising costs, manufacturers require test systems optimized for efficiency.
-
Product
Spring Clip Fixture
16092A
Test Fixture
Use this test fixture with parallel electrodes for impedance evaluation of both lead and SMD components.
-
Product
CDMA2k Analysis Using NI PXI RF Test Instruments
NI-RFmx CDMA2k
Test Instrument
NI-RFmx CDMA2k is completely interoperable with all NI-RFmx APIs. It provides simple access to the most advanced optimization techniques such as multi-measurement parallelism and multi-DUT measurements. The result is extremely fast and high-quality measurements with minimal software development effort.
-
Product
Electronics Functional Test
Functional Test
Functional test for productive manufacturing. Manufacturers of products enabled by electronics must assure proper operation prior to shipment. Bloomy’s line of universal test systems are ideal for functional test of your PCBAs and subassemblies, from the simplest to the most complex. The UTS family of products combines high-performance test instruments, switching, power control and mass-interconnect hardware with our robust UTS software suite into a low-risk, cost-effective and powerful test solution for your device under test (DUT).
-
Product
Semiconductors Testing
test
Our Testers support the production lines of variety of products such as 40/100 GBps Mux/DeMux, LNA, WiMAX RF Transceivers, Microwave & Millimeter Wave components. This high reliability products are being used in (a) Networking & Communications (b) Consumer Electronics (c) Military & Space
-
Product
Regenerative Battery Pack Test System
17040
Test System
Conforms to international standards for battery testing: IEC, ISO, UL, and GB/T, etc.Regenerative battery energy discharge (Eff. >90%, PF >0.95, I_THD <5%)Multiple voltage and current ranges for auto ranging function to provide optimum resolutionHigh accuracy current/voltage measurement (0.05%FS/0.02%FS)2ms current slew rate (-90% ~ 90%)Dynamic (current/power) driving profile simulation tests for NEDC, FUDS, HPPCTest channel parallel functionTest data analysis functionData recovery protection (after power failure)Automatic protection for error conditionBattery simulator (option)High power testing equipment- Voltage range : 80~1000V - Current range : 0~750A - Power range : 0~300kWCustomized integration functions- Integrated temperature chamber - BMS data analysis - Multi-channel voltage/temperature recording
-
Product
Test System
BMS HIL
Test System
The BMS Hardware-in-the-Loop (HIL) Test System is a high performance platform providing all necessary input signals used for battery pack simulation. A real-time operating system executes complex cell and pack models commonly used for BMS algorithm development and firmware regression testing.
-
Product
Ethernet and Fibre Channel Test Platform
SierraNet M1288
Test Platform
The SierraNet M1288 Ethernet and Fibre Channel test platform provides best in class analysis, jamming and generation for traffic capture and manipulation for testing application and link characteristics. SierraNet M1288 is the latest in the line of industry leading test and measurement tools from Teledyne LeCroy, designed for today’s high-speed storage and communications fabrics. SierraNet M1288 supports examination and modification of Ethernet and Fibre Channel links utilizing both Pulse Amplitude Modulation 4 (PAM4) and legacy Non-Return to Zero (NRZ) technologies.
-
Product
Test System for High Volume Production Testing of Integrated Circuits
ETS-364
Test System
The ETS-364 is a general-purpose precision analog and mixed-signal test platform designed for high volume production testing of integrated circuits; optimized for high throughput applications with a fully integrated multisite software and hardware architecture.
-
Product
Benchtop Communication Test System
ATS3000A
Test System
The ATS3000A is designed using Astronics Test Systems’ proven Synthetic Instrumentation architecture. Featuring 23 instruments, and both Automated and Standalone modes to test, record, and diagnose faults, the unit provides complete RF, Analog and Digital capabilities. The ATS3000A also includes the sophisticated IF and baseband I/Q Digital Signal Processing required for modern radios. The fieldupgradeable, software-defined architecture features easy-touse graphical user interfaces and enables testing with minimal operator intervention. Test Program Sets areavailable for a full range of tactical radios, or you can create new TPSs easily using the included TestEZ® software suite.
-
Product
EOL/Functional Testing
Functional Test
Whether you are testing RF LRU modules as a defense contractor, or implementing the next power supply tester for EV charge stations, ARC can create a custom, flexible automated end of line test solution for a variety of needs, with your budget in mind.Leverage our expertise with PXI mixed signal modular instruments, RF test capabilities and switching to complete your next solutions. Shorten your test development times, improve hardware and software standardization, and control your future test development costs by partnering with ARC on your next project.
-
Product
Wireless Test Standards Software
test
Generate and analyze signals for cellular and connectivity standards with NI PXI RF instrumentationPerform advanced automated test with the easy-to-use NI-RFmx software APISave on all NI RF wireless test software under a single license
-
Product
Portable, Integrated O-Level Test Platform
Guardian™
Test Platform
Guardian is a ruggedized automated testing platform that quickly and accurately verifies the operational readiness of complex electronics systems in aircraft, ships, and vehicles.
-
Product
Environmental Control System Test Platform
Test Platform
The Airframe Environmental Control System Test Platform provides a hardware-in-the-loop (HIL) closed-loop test environment for dynamic and maintenance testing of cockpit and cabin environmental control systems for airframes. The system simulates a military or commercial airframe cabin, including sensors and actuators from the control system and the passengers. The system delivers repeatable, cost-effective testing in a fraction of the time needed with typical in-house simulation systems.
-
Product
Multiple Module Serial Bus Test Instrument
Bi4-Series
Test Instrument
The wide variety of serial buses used in defense and aerospace applications typically requires multiple single-purpose instruments. Too often, they are difficult to reconfigure in order to test a different application.The Bi4-Series provides all the capabilities needed for complete communications bus access test for up to four serial buses used in board level (SRA/SRU) and box level (WRA/LRU) equipment—all in a single VXI module.The instrument includes test applications, industry-compliant software drivers and hardware enabling straightforward integration into automatic test systems.With the configuration flexibility needed to effectively test every bus format used in defense and aerospace applications, the Bi4-Series instrument plays a key role in reducing implementation time and test system cost.
-
Product
Application Software for Electronic Test & Instrumentation
test
Application software provides configuration-based workflows for electronic test and instrumentation applications. Application software is part of the NI software portfolio.
-
Product
Mixed Signal Battery Test System
Test System
The Mixed-Signal Battery-Test System is an automated test platform designed to meet today’s advanced battery test requirements. The platform is ideal for testing a range of battery cells and packs, and can be used in applications such as research and design, quality control, and end-of-line manufacturing. Its distributed architecture provides a scalable solution with configurable system components to accommodate specific applications.
-
Product
FPD Tester Model
27014
Test Platform
Chroma 27014 Flat Panel Display Tester is a complete testing solution that meets the Liquid Crystal Module testing requirements of production line. With integrated video generator, multi-channel precision power supply and process control unit, the system allows a complete test of signal, pattern and electrical parameters of LCM through a PC or remote control box.
