-
product
Power Conditioner
ACT2500 Series
Acumentrics continues to provide innovative, rugged, reliable power solutions with the introduction of the ACT2500 Power Conditioner. This durable and versatile power conditioning system contains advanced double on-line conversion to provide power conditioning for electronic devices, meeting the rigorous needs of soldiers operating around the world. The ACT2500 "Vetronics" ready design makes it perfect for combat vehicles including the JLVT, FMTV and HMMWV along with any other application that relies on 28VDC as a source of power.
-
product
Panel-mounted Voltage Power Amplifier
PAV120Bi
PAV120Bi is specially designed for R&D of power system simulation. It is adapt to various capacitive and inductive load. It is with 6 channels voltage outputs, each channel with 120V/60VA maximum output.
-
product
PXI Solid State Multiplexer Module, Dual 3-Channel, 10 A, Hardware Interlock
40-666B-011-HI
The 40-666B-011-HI is a dual 3-channel 10A MUX with hardware interlock and is part of our range of high current multiplexers occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation.
-
product
Power Supplies
Encore Electronics offers the following line of power supplies, ranging from 5 watts to 500 watts. Many of these supplies have been specifically designed to mechanically and electrically replace existing units from other vendors that no longer offer linear-regulated power supplies.
-
product
Power Dividers
Teledyne Microwave Solutions (TMS) offers several In-Phase Two-Way Power Dividers with high isolation, low insertion loss, excellent phase and amplitude balance in a small size for a variety of communications applications.
-
product
PXI 8 Slot BRIC Matrix, Solid State, 256x8, 1-Pole (8 sub-cards)
40-563B-121-256X8
The 40-563B-121-256x8 is an ultra high density 8-slot matrix module with 1-pole switching and is part of our range PXI BRIC matrices. They are available in 2, 4 or 8-slot sizes to suit high performance PXI switching requirements and are constructed using solid state switches.
-
product
Components - Low Noise Amplifiers (FLNA)
FLNA series
Farran's FLNA series low noise amplifiers are constructed with discrete or MMIC pHEMT devices that operate over the frequency range 18 to 110 GHz. These amplifiers are specifically designed for low noise applications.The amplifiers are offered in two categories: standard and custom-built. The custom-built amplifiers are offered in various RF interfaces, including standard waveguide or coaxial connectors, for convenient system integration.
-
product
Power Amplifiers
RF Range
The RF power amplifier range from Laplace is specifically designed for EMC Immunity testing. These are compact units with characteristics matched to the requirements of IEC standards.
-
product
Low Noise Amplifier
R&K’s Low Noise Amplifier (LNA) series products are a type of small signal amplifiers but with excellent noise figure. LNA is designed to significantly minimize additional noise to be introduced inside the product, and capable to amplify the input RF signal to the required level with minimal impact from noise on output RF signal.
-
product
Charge Amplifier
ZET 440
Charge amplifier ZET 440 for piezoelectric detectors is intended for:*amplification and conversion of output signals of primary piezoelectric transducers with charge output;*amplification and conversion of output signals of primary transducers with the IEPE type in-built electronics to voltage;*gain ratios: 1, 10, 100;*LPF: 0.1, 1, 10 Hz
-
product
Power Sensors
N8480 Series
N8480 thermocouple power sensors, integrated with EEPROM capability, are the latest RF sensor applications with excellent measurement accuracy, repeatability, and linearity.
-
-
product
Regenerative Power System, 20 V, ±400 A, 5 KW, 200/208 VAC
RP7931A
The Keysight RP7931A regenerative power system is a single output, bi-directional, regenerative DC power supply with highly integrated safety features that protect both your people and your device under test.
-
product
8.75 (222.25) 19" Solid Panel
P-0819
Special grade .125” sheet aluminum (5052-H32 EPS). Each side, edge and corner is carefully de-burred and chamfered to provide a flawless finish, resulting in a superior quality panel. Finish is textured unless otherwise specified.
-
product
Power Meters
Chroma Systems Solutions, Inc.
Chroma’s Digital Power Meters are designed for both single-phase and multiple phase measurements of AC power signals and related parameters common to most electronic products. Instead of traditional analog measurement circuits the 66200 Digital Power Meter uses state-of-the-art DSP digitizing technology. The internal 16 bits analog/digital converters with sampling rates of up to 200KHz provide both high speed and high accuracy measurements which is unprecedented within the industry for this class of power meters current on the market.
-
product
Power Supplies
Our short-circuit-proof, single or triple-phase power supplies for automation are approved according to CE/TÜV, UL and CCC. Different voltages of 12 V, 24 V and 48 V can be selected. The most important features: top-hat rail assembly, status display, regulatable output voltage, parallel connection, ready and alarm output. Output power of 18 to 960 W. Protection class IP20.
-
product
Power Supplies
Fujian Lilliput Optoelectronics Technology Co., Ltd.
We are one of the leading and professional power supplies manufacturers and suppliers in China. Thanks to our highly qualified experts and advanced technology, we are also one of the world's leading brands. Welcome to buy the quality, cheap and durable desktop power supply, power supply digital in stock from us. Check the quotation with us now.
-
product
Load Cell DIN Rail Signal Amplifier
LCD20
Our intelligent strain gauge bridge amplifier is a compact, stackable microprocessor based unit specifically designed to control and monitor process applications. Flexible connection to most load cells, pressure or strain gauges over a wide range of sensitivities. The unit provides isolated current 4-20mA and voltage 0-10V analogue outputs and two digital inputs. Two set point relays can be configured to set thresholds such as net, gross, peak and valley. Powered from a wide ranging DC supply, the DIN rail amplifier is supplied with 2 part screw connectors for ease of installation.
-
product
RF High Power Amplifier Modules
Analog Devices MMIC-based GaN and GaAs power amplifiers cover the low hundred MHz frequency range up through and including components in the Ka-band (29 GHz to 31 GHz). Our portfolio also includes GaN-based power amplifier modules with output power exceeding 8 kW. Designed for excellent linearity at high output power, our power amplifiers maintain good heat dissipation and high reliability at elevated temperatures for the wide variety of test, radar, and aerospace and defense applications that they are used in.
-
product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J0
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
product
Power Probes
RkT Thermopile Series
The RkT Series thermopile power probes are ideal for measuring Nd:YAG, CO2, and other mid-power lasers. The probes are designed to withstand average power densities up to 20kW/cm2 (15MW/cm2 peak pulse power density). The flat UV to far-IR spectral response allows the probes to measure broadband sources as well. Measure the power of cw sources or the average power of sources pulsed at 5Hz or greater.
-
product
Power Supply
Model 62-4PS
FEATURES: Supports All 62 Series Converters; Internally Regulated +12, - 12 & +5 Volts; 110 & 220 Units. The Model 62-4PS is a small wall mount that is used to supply power to any of the Series 62 Interface Converters. The 62-4PS contains internal regulators to provide +12, -12 and +5 Volts. Note that the 220 Volt unit is not a wall mount.
-
-
product
Analog Control Variable Gain Amplifiers (VGAs)
Analog Devices voltage controlled variable gain amplifiers provide continuous gain control over a wide dynamic range for a variety of audio and optical frequency bands. Our VGAs improve the dynamic range of a circuit by allowing users to adjust a signal’s amplitude in real time, which is invaluable for ultrasound, speech analysis, radar, wireless communications, and instrumentation-related applications.
-
product
Power Supplies
VP SERIES
Crafted for quality, performance and incredible value. This entry-level solution gives you everything you need in a power supply. No twinkly lights or glittery paint jobs - a 120 mm fan for effective and quiet cooling, dual +12V rails for amazingly stable power and heavy-duty protection circuitry for peace of mind, no matter how demanding your system. And it comes with all the assurance of Antec's AQ2 Antec Quality 2 year limited warranty. All the features, none of the waste: for builders that are strictly business, the VP550F is strictly power.
-
product
GHZ-Wideband Amplifiers
Ultra-wide bandwidth from 10 kHz up to 2.5 GHzGain up to 60 dB (x 1,000)Transimpedance gain with photodetectors up to 50,000 V/AVery low input noise down to 310 pV/√Hz (6.2 pA/√Hz)Integrated DC-current path for biased photodetector applicationsTwo identical signal outputs (HSA-Y series)DC-monitor output (HSA-Y series)
-
product
Amplifiers
Amplifiers are used to amplify the energy output of photodetectors as well as convert their electrical signal for a number of illumination measurement or spectroscopy applications. Amplifiers are digital systems that amplify the low electrical current transmitted by photodetectors to easily detectable levels. Amplifiers also convert photodetectors' electrical current into voltage so that their signal may be read by other digital devices. Amplifiers are indispensable for nearly any light measurement applications by greatly increasing the usability of a detector system.
-
product
Power Dividers
Corech Microwave’s Power Dividers also called power splitters, frequency ranges from DC -67 GHz, featured with ultra wideband, multi ways and high power options. 2/3/4/5/6/8/10/12/16 ways designs are available, low insertion loss and high isolation.
-
product
Amplifiers
Amplifier is designed to be used in conjunction with optional modules and can be confiugured for up to 8 inputs and 8 outputs. 9000 series modules as well as existing 900 series input modules can be used. The more appropriate modules can be selected depending on applications. Since it comes with two 60W power amplifiers, it can individually perform multi-origin braodcasts. It is equipped with singnal processing and control functions necessary for sound reinforcement, permitting all parameters to be set at the mixer. Settings data can be stored inside the unit and called up using the keys on the front panel.
-
product
C-Band Separate Raman Fiber Amplifier
RFA5000
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
